• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1302-1306
• /
• 2007

여름철의 강우시 저수지에 주로 유입되는 고탁수층은 저수지내의 수체에 대하여 밀도차와 유속차를 가지며, 난류혼합을 일으키면서 주변수를 유입하며 하류방향으로 이송 확산되어 간다. 임하댐과 같은 대형 저수지는 수심이 30 m가 넘는 관계로 여름철에 2개의 수온약층이 존재한다. 따라서 댐체에 도달한 고탁수층은 저수지내의 밀도성층으로 인하여 주로 중층에 분포하게 되며, 가을철에 발생하는 수평확산과 전도현상으로 인해 저수지 전역에 분포하게 되어 탁질입자의 분포에 따라 탁수현상의 장기화를 유발하기도 한다. 이와 같은 탁수문제의 저수지내 대책으로는 홍수기에 고탁수층을 우선적으로 취수하는 방법이 있다. 고탁수층은 이와같이 수온약층과 밀접한 관계를 가지며, 취수탑 주변의 선택취수 결과에 영향을 받는다. 형성된 탁수층을 효율적으로 선택배제하기 위해서는 취수시설에 접근하는 성층흐름을 정확하게 이해해야 한다. 본 연구에서는 3차원 CFD를 사용하여 밀도성층에 따른 취수탑 주변의 접근흐름을 수치해석하여 방류수심, 방류유속 및 밀도성층구조의 선택배제에 대한 영향을 분석하였다. 임하댐 취수설비에 적용한 결과에 의하면 상층, 중층, 하층에서 취수탑 문비를 개도하였을 경우, 취수탑 주변에서만 유속이 증가하였을 뿐 저수지 내에서는 유속이 크게 증가되지 않은 것으로 나타났다. 하지만 문비 개도구간의 변화에 따라 수심별 유속분포는 크게 변화하는 것을 확인할 수 있다. 따라서 문비를 조절하는 것은 저수지 전체의 유동을 깨뜨리지 않으면서 취수탑 인근에서 선택취수가 가능하다는 것을 확인할 수 있었다. 또한 본 연구에서는 정밀한 현장조사를 수행하여 저수지와 방류수의 탁도변화를 모니터링하였으며, 취수탑 개구부 주변의 연직 유속분포를 측정하였다. 3차원 수치모의 결과와 현장에서 관측한 유속장을 비교함으로써 본 연구에서 제시한 실제 탁수배제능력을 검증하였다.를 구축하였다는데 의의가 있다.로와 접하는 건물의 경우 모서리부 광고 효과가 지배적이며 대부분 곡선돌출형이 사용되고 있었다. 그러므로 모서리 저층부를 필로티로 계획하여 보행흐름을 원활하게 하고 대신 입면을 투명하게 하여 간접광고(내부전시) 효과를 유도하는 것이 좋다. 특히 원형모서리는 건물 특화 성격이 강하므로 불가피할 경우 소형 액센트 광고 위치를 미리 벽면으로 할애하는 것이 경관 및 입면계획에 유리한 것으로 분석되었다. 불확실도 해석모형 등의 새로운 기능을 추가하여 제시하였다. 모든 입출력자료는 프로젝트 단위별로 운영되어 data의 관리가 손쉽도록 하였으며 결과를 DB에 저장하여 다른 모형에서도 적용할 수 있도록 하였다. 그리고 HyGIS-HMS 및 HyGIS-RAS 모형에서 강우-유출-하도 수리해석-범람해석 등이 일괄되게 하나의 시스템 내에서 구현될 수 있도록 하였다. 따라서 HyGIS와 통합된 수리, 수문모형은 국내 하천 및 유역에 적합한 시스템으로서 향후 HydroInformatics 구현을 염두에 둔 특화된 국내 수자원 분야 소프트웨어의 개발에 기본 토대를 제공할 것으로 판단된다.았다. 또한 저자들의 임상병리학적 연구결과가 다른 문헌에서 보고된 소아 신증후군의 연구결과와 큰 차이를 보이지 않음을 알 수 있었다. 자극에 차이가 있지 않나 추측되며 이에 관한 추후 연구가 요망된다. 총대장통과시간의 단축은 결장 분절 모두에서 줄어들어 나타났으나 좌측결장 통과시간의 감소 및 이로 인한 이 부위의 통과시간 비율의 저하가 가장 주요하였다. 이러한 결과는 차가운 생수 섭취가 주로 결장 근위부를 자극하는 효과를 발휘하는 것이 아닌가 해석된다. 이와 같은 연구결과를 통해 생다시마를 주원료로 개발된 생다시마차와 생다시마 음료가 만성 기능성 변비 증세를 개선하는 효능이 잠재적으로 있음을 확인하였다. 그러나 생약제재의 변비약 수준으로

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.22 no.4
• /
• pp.215-223
• /
• 2010

A seasonal circulation patterns in the Chinju Bay (CB) were suggested from the observed data at two channels of the Noryang Channel (NC) and the Daebang Channel (DC) during the period from 2005 to 2008. The water circulation in the CB is mainly controlled through the NC and the DC. In winter, tidal current at the surface layer of the NC flows from the Kwangyang Bay (KB) eastward into the CB, whereas the current at the bottom layer flows from the CB westward into the KB. In summer, tidal current at the surface layer of the NC goes from the CB westward into the KB. The flow system at the NC shows the typical pattern of thermohaline circulation. In spring, tidal current at the surface layer of the eastern part of the DC flows out into southeastern open ocean. However, in summer, the current in the western part of the DC flows into the CB through the DC. Also, the velocity in the western part of DC is 50~70 cm/sec stronger than that in the eastern part. To obtain better understanding on the seasonal circulation pattern in the NC and the DC, additionally the detailed studies on the field measurements and three dimensional numerical modeling are needed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.12
• /
• pp.74-79
• /
• 2017

The fire extinguishing performance of hybrid nozzle systems is improved by injecting an extinguishing agent concentrically into the target site and, in this study, water mist is used as a water curtain to confine the droplets of the agent. In this study, we numerically investigated the effect of the foundation angle and injection pressure on the performance of a hybrid nozzle by evaluating the mean radius of the volume fractions of the agent and water mists. An experiment involving a water mist nozzle was carried out to validate the numerical method and then the droplet behaviors, e.g., stochastic collision, coalescence and breakup, were calculated with 2-way interaction Discrete Particle Modeling (DPM) in the steady state for the hybrid nozzle system. The mean radius of the water mists increased by about 40 %, whereas that of the agent decreased by about 21 %, when the injection pressure was increased from 30 bar to 60 bar. In addition, the mean radius of the agent increased by about 24 % as the foundation angle of the hybrid nozzle head increased from $30^{\circ}$ to $60^{\circ}$. As a result, it can be inferred that the injection angle and pressure are important factors for hybrid water mist designs.

• Journal of Korea Water Resources Association
• /
• v.48 no.12
• /
• pp.1023-1035
• /
• 2015

This study applies 3-D N-S solver based on PBM (Porous Body Model), LED-WASS-3D ver 2.0 to directly analyze non-linear interaction of seawater-freshwater-coastal aquifer in order to simulate the seawater infiltration into coastal aquifer. This numerical simulation is the first trial in Korea, as well as unusual and new numerical analysis abroad. Firstly, to validate the applied numerical model, the validity and effectiveness was verified for the numerical model by comparing and considering it with the result of laboratory experiment for seawater-freshwater interface in coastal aquifer. And then it simulated the seawater infiltration into coastal aquifer considering the changed levels of seawater and groundwater in order to analyze the distribution characteristics of flow field and seawater-freshwater interface of coastal aquifer as the level difference between seawater and groundwater and rate of seawater level (${\Delta}h/h$) increased. In addition, the characteristics of seawater infiltration were analyzed from the vertical salinity in the coastal aquifer by ${\Delta}h/h$, which cannot be obtained from existing non-diffusion numerical models. Finally, it analyzed the effect of ${\Delta}h/h$ on the seawater infiltration distance in coastal aquifer, which was indexed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.10
• /
• pp.1265-1273
• /
• 1999

PIV(Particle Image Velocimetry) velocity field measurements inside the snout of a1/10 scale model of the Zn plating process were carried out at the strip speed $V_s=1.5m/s$. Aluminum powder particles ($1{\mu}m$) and atomized olive oil ($3{\mu}m$) were used as seeding particles to simulate the molten Zinc flow and deoxidization gas flow, respectively. A pulsed Nd:Yag laser and a $2K{\times}2K$ high-resolution CCD camera were synchronized for the PIV velocity field measurement. From flow visualization study, it is found that the liquid flow in the Zn pot is dominantly governed by the uprising flow caused by the rotating sink roll, with its effect on the steel strip inside the snout largely diminished by installing of the snout. The deoxidization gas flow in front of the strip inside the snout can be characterized by a large-scale vortex rotating clockwise direction formed by the moving strip. In the rear side of the strip, a counter-clockwise vortex is formed and some of the flow entrained by the moving strip impinges on the free surface of molten zinc. The liquid flow in front of the strip is governed by the flow entering the snout, caused by the spinning sink roll. Just below the free surface a counter-clockwise vortex is formed near the snout wall. The moving strip affects dominantly the flow behind the strip inside the snout, and large amount of the liquid flow follows the moving strip toward the sink roll. The thickness of the flow following the strip is very thin in the front side due to the uprising flow, however thick boundary layer is formed in the rear side of the strip. Its thickness is increased as moving downstream toward the sink roll. Inside the snout, the deoxidization gas flow above the free surface is much faster than the liquid flow in the zinc pot. Due to the larger influx of the flow following the moving strip in the rear side of the strip, higher percentage of imperfection can be anticipated on the rear surface of the strip.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.14 no.3
• /
• pp.197-203
• /
• 2008

This study analyzed the characteristics of sea water transport between Busan New-port and the Nakdong River estuary. Numerical modeling was used to evaluate the characteristics of the tidal current. Numerical simulations of three different topographies were conducted. The results are summarized as follows: 1) The volume of sea water transport was reduced by $0.7{\sim}18.4%$ when water depth was decreased at Busan New-port (10 m); 2) The volume of sea water transport was increased by $3.5{\sim}21.9%$ when a channel (depth 5 m) was constructed in the direction of the Nakdong River estuary.

• Tunnel and Underground Space
• /
• v.8 no.4
• /
• pp.275-286
• /
• 1998

The effective permeability and the representative element volume(REV) of fracture network model were evaluated based on the parameters such as permeability tensor, principal permeability and the direction of principal permeability. The effective permeability ranges between the harmonic mean and the arithmetic mean of the local permeabilities of subdivided blocks. From the numerical experiments, which were for investigating the influence of model volume on the variation of flux for the cubic models, it was found that the variation of flux became reduced as the model volume approached REV. The variation of groundwater flux into the tunnel in the fracture network model was mainly dependent on the ratio of the tunnel length to model size rather than REV. And it was found that groundwater flux into the tunnel was not completely consistent between the fracture network model and the equivalent porous media model, especially when the ratio of the tunnel length to model size is small.

• The Journal of the Korea Contents Association
• /
• v.15 no.10
• /
• pp.504-516
• /
• 2015

This study addresses one of the curent issues in modern finance, which investigates financial profile on the levels of the chaebol firms' cash hoardings in the domestic capital market. Iit may be imperative to search for robust and consistent financial determinants of cash holdings as well as identifying any changes or trend of the determinants affecting the corporate cash reserves in the post-era of the global financial turmoil, considering that interest parties at the government and corporate levels, still seem to have a controversy or debate on excess cash savings. Two hypotheses were postulated and empirically tested for the chaebol firms in the study, such as any transitional changes of the relevant factors on cash holdings and unique attributes of financial factors discriminating between the different type of domestic stock markets.

• Tunnel and Underground Space
• /
• v.32 no.3
• /
• pp.219-230
• /
• 2022

The Geo-Reservoir Experimental Analogue Technology (GREAT) cell was designed to recreate the thermal-hydro-mechanical conditions of deep subsurface in the laboratory. This apparatus can generate a polyaxial stress field using lateral loading elements, which rotate around the longitudinal axis of a sample and is capable of performing a fluid flow test for samples containing fractures. In the present study, numerical simulations were carried out for triaxial compression tests using the GREAT cell and the mechanical behavior of samples under different conditions of lateral loading was investigated. We simulated an actual case, in which triaxial compression tests were conducted for a polymer sample without fractures, and compared the results between the numerical analysis and experiment. The surface strain (circumferential strain) of the sample was analyzed for equal and non-equal horizontal confining pressures. The results of the comparison showed a good consistency. Additionally, for synthetic cases with a fracture, we investigated the effect of the friction and type of fracture surface on the deformation behavior.

• Journal of Industrial Convergence
• /
• v.21 no.7
• /
• pp.83-92
• /
• 2023

The bullet shape of the plasma jet using the atmospheric-pressure dielectric barrier discharge method changes depending on the applied fluid rate and the intensity of the electric field. This changes appear as a difference in spectral distribution due to a difference in density of the DBD plasma jet. It is an important factor in utilizing the plasma device that difference between the occurrence of active species and the intensity through the analysis of the spectrum of the generated plasma jet. In this paper, a plasma jet generator of the atmospheric pressure volume DBD method using Ar gas was make a prototype in accordance with the proposed design method. The characteristics jet fluid rate analysis of Ar gas was accomplished through simulation to determine the dependence of flow rate for the generation of plasma jets, and the characteristics of plasma jets using spectrometers were analyzed in the prototype system to generate optimal plasma jet bullet shapes through MFC flow control. Through the design method of the proposed system, the method of establishing the optimal plasma jet characteristics in the device and the results of active species on the EOS were verified.