• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2009.10a
• /
• pp.132-133
• /
• 2009

부산 수영만 해상케이블카 설치예정수역에서 파랑 및 유동환경에 대한 기본 자료 조사와 아울러 대상해역에서 구조물을 설치하였을 때 주요 입사파에 대한 파랑 및 유통환경 변화 특성을 수치모텔 시뮬레이션으로 분석하여 타당성을 검토하고자 하였다. 대상해역에서 광안대교가 설치된 조건이나 이의 외해측으로 일련의 해상케이블 지지구조물을 설치함에 따라 발생할 수 있는 환경 중 해저저질의 이동 및 표사에 영향을 미치는 파랑과 유동장 해석을 대상으로 하였다. 파랑해석은 SWAN 모델을 이용하여 분석하였고, 유동장 해석은 MIKE21 HD 모듈을 이용하여 해석하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.10
• /
• pp.939-946
• /
• 2008

Euler codes or Navier-Stokes codes for compressible flows suffer severe degradation in convergence as Mach number approaches zero. The convergence problem arose from the wide disparity in characteristic speeds can be solved using preconditioning methods without large modifications. In this paper, a preconditioned RANS(Reynolds Averaged Navier-Stokes) solver is developed for analysis of low Mach number flows. In order to validate the method, computational examples are chosen and the results are compared with the experimental data and the existing computed results showing a good accuracy and convergence characteristics for steady inviscid, laminar and turbulent flows at low Mach number.

• Journal of Aerospace System Engineering
• /
• v.12 no.4
• /
• pp.81-89
• /
• 2018

In the present study, a numerical investigation was conducted to analyze the effect of the distance between the adjacent injectors on the characteristics of flow structure, fuel penetration, and air/fuel mixing. Numerical results were validated with experimental data using a single injection. Subsequently, the same injector geometry and properties were applied on a non-reacting flow simulation with multiple injectors. Total pressure loss, penetration height, and mixing efficiency were compared with the distance between the injectors. The results showed that each injected gas merged into a single stream, resulting in the 2D-like flow fields under the condition of short distance and lower mixing efficiency along with higher total pressure loss. When the distance between the injectors increased, total pressure loss reduced and mixing efficiency increased due to the weakening of interactions between the injected gases.

• Journal of Energy Engineering
• /
• v.20 no.4
• /
• pp.338-345
• /
• 2011

The swirl flow applied for high efficiency and reduction of emission such as NOx, CO in a gas turbine engine makes recirculation zone by shear layer in the combustion chamber. This recirculation zone influences a decreasing flame temperature and flame length by burned gas recirculation. Also it is able to suppress from instability in lean-premixed flame. In this study, it was found that the swirl flow field was characterized as function of swirl number using PIV measurement in dump combustor. As increasing swirl number, a change of flow field was presented and recirculation zone was shifted in the nozzle exit direction. Also turbulent intensity and turbulent length scale in combustor were decreased in combustion. It has shown reduction of eddies scale with swirl number increasing.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1292-1300
• /
• 1989

본 연구에서는 비원형관의 평판길이의 변화가 평판과 원관사이의 상호작용 으로 나타나는 온도장, 유동장, 국소 Nusselt 수 및 평균 Nusselt 수에 미치는 영향 에 대하여 고찰하였다.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.107-118
• /
• 2011

This paper performs flow analysis of ultra-high speed vehicle inside the long distance tunnel. One and three dimensional hybrid mesh was used for describing moving motion and flow analysis of an vehicle inside a long distance tunnel which over 20 km. Flow analysis and aerodynamic drag measuring were performed by three dimensional mesh: around vehicle, and pressure waves of a tunnel was measured by one dimensional mesh: the other region where rare changing of flow pattern.

• Journal of Energy Engineering
• /
• v.24 no.3
• /
• pp.122-127
• /
• 2015

We carried out three-dimensional flow analysis in a clean room. Flow field in a robot experiment system, induced from the moving robot, is numerically studied in this paper. The effects of moving robot in a clean room are investigated in order to find the section of dust accumulation. Contamination on the bottom produced from the moving robot is predicted from the analysis results from the flow fields. Results show that a large swirl flow is formed around the moving robot. Consequently, the optimal flow condition can be obtained by controlling the fluid velocity through the fixing of inlet or outlet position.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.445-450
• /
• 2011

Swirling flows inside a swirl mixing chamber are investigated for simple configuration where swirl is produced by a tangential entry type swirl generator. The flow downstream of the swirl generator has been quantified by measurements two velocity components and their corresponding mean values along axial and radial direction using Particle Image Velocimetry(PIV). The mass flow rate of the tangential entry is increased in order to study their effect on the flow field. From the measurement profile of velocity and vorticity, flow mixing characteristics in a swirl mixing chamber are evaluated.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.3
• /
• pp.31-39
• /
• 2011

The flowfield in a solid rocket motor was simulated at the wall-injection test model, which has a fin-slot grain and submerged nozzle, and visualized by a smoke-wire. The high speed CCD camera captured the visualized images around the nozzle inlet through the grain center port. The vortical tube structure and circumferential flow patterns at the nozzle throat were visualized. The radial momentum transfer caused by the shear-interactions of slot-outlet flow, fin-base flow and grain port flow from upstream worked as the source of these phenomena.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2008.05a
• /
• pp.30.2-30.2
• /
• 2008