• Journal of the Korean Magnetics Society
• /
• v.8 no.5
• /
• pp.261-269
• /
• 1998

Induced anisotropy with the energy of $6{\times}10^4\; J/m^3$ is obtained in amorphous Sm-Fe based thin films which are fabricated by rf magnetron sputtering under a magnetic field of 500~600 Oe. Compared with conventional thin films, the anisotropic thin films exhibit a similar "saturation" magnetostriction, but show a very large anisotropy in magnetorstiction which is of significant practical importance due to increased strain at a particular direction. It is shown from a systematic investigation over a wide composition range for binary Sm-Fe alloys that anisotropy is also induced, though small, during a normal sputtering procedure due to the stray field, and the largest anisotropy is observed in the composition range of 25~30 at.% Sm. Furthermore, induced anisotropy is also found to be formed by magnetic annealing, but the anisotropy energy is much smaller than that by magnetic sputtering. This may be because the volume diffusion by which atoms move during magnetic annealing to from induced anisotropy is much slower than the surface diffusion which is expected to be a dominant factor during magnetic sputtering.puttering.

• Journal of the Korean Magnetics Society
• /
• v.12 no.2
• /
• pp.46-50
• /
• 2002

Soft magnetic Mumetal thin film was fabricated under magnetic field at various substrate temperatures. High vacuum annealing was carried out at 200$\^{C}$ during 1 hr. The in-plane anisotropy of Mumetal thin film was determined from hysteresis loops measured by VSM when the sample axis varied from the field direction from 0°to 180°. As the substrate temperature increases, the coercivity in easy direction decreases, but uniaxial anisotropy deviates from the field direction. After vacuum annealing at 200$\^{C}$ for 1 hr, the uniaxial anisotropy is improved irrespective of substrate temperature. When the substrate temperature was 50$\^{C}$, the anisotropy field is 4.3 Oe. As the substrate temperature increases anisotropy field decreases. Uniaxial anisotropy of Mumetal thin film was formed best at 50$\^{C}$ before and after annealing.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.3
• /
• pp.151-156
• /
• 1998

코발트계 비정질 합금을 여러 온도 구간 및 시간에 대해서 열처리하며 표면 결정화 현상이 자기 이방성에 미치는 영향을 탐구하였다. 자기 이방성은 비정질 표면의 결정 구조에 민감한 변화를 보였는데 면심입방점 코발트에 많은 결함이 존재할 경우 자기이방성이 최대치를 나타내였다.

• Proceedings of the Korean Magnestics Society Conference
• /
• 1999.04a
• /
• pp.80-81
• /
• 1999

• Journal of the Korean Magnetics Society
• /
• v.15 no.1
• /
• pp.25-29
• /
• 2005

Magnetic properties of YIG films grown by solid phase epitaxy (SPE) was measured as a function of temperature with focus on magneto-crystalline and perpendicular magnetic anisotropy. Perpendicular magnetic anisotropy was not induced in the SPE YIG films annealed at low temperature by relaxing residual stress through formation of dislocation. On the contrary the films annealed at high temperature showed perpendicular magnetic anisotropy which shows very low density of dislocation. Perpendicular magnetic anisotropy field decreased linearly up to a high temperature of $230^{\circ}C$ above which magneto-crystalline anisotropy disappeared. Coercivity also decreased linearly with temperature up 세 $230^{\circ}C$. Magneto-crystalline anisotropy of perpendicular anisotropy induced epitaxial (111) YIG films can be measured using $H_k=4K_1/3M_s$. Temperature behavior of initial susceptibility can be successfully explained by Hopkinson effects. Curie temperature of YIG films grown on GGG substrate with high paramagnetic susceptibility can be easily measured using the results.

• Journal of the Korean Magnetics Society
• /
• v.1 no.2
• /
• pp.42-48
• /
• 1991

The basic soft magnetic characteristics of a typical Fe based amorphous $Fe_{80}B_{15}Si_{5}$ alloy were measured with pulse metheod. Quantitative relations between magnetostriction, anisotropy energy, reluctivity were investigated. The relative contribution factor of magnetostrictive and uniaxial anisotropy energy to the reluctivity were calculated. The internal stress and induced anisotropy were estimated. A tension applied to the long axis of the sample greatly enhanced induced anisotropy.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.2
• /
• pp.1-6
• /
• 2007

This study investigated the magnetic properties of $Ni_{80}Fe_{20}/SiO_2$ laminates with shape-induced magnetic anisotropy. The multilayer films were deposited on Si or upilex substrates, from separate $Ni_{80}Fe_{20}$ and $SiO_2$ (at %) alloy targets using a rf diode sputtering system. $Ni_{80}Fe_{20}/SiO_2$ laminates with a various number of bilayers (N) were prepared. The laminates with ellipse array patterns were prepared using photolithographic technique. The magnetic properties were measured at room temperature using a B-H hysteresisgraph and a high frequency permeameter. The several steps during domain wall reversal were observed in multilayer films, attributing to inter-magnetic layer coupling. Intrinsic uniaxial anisotropy field increases with N. The experimental values of the total anisotropy field are found to be in good agreement with the calculated values. This study utilized the shape anisotropy of the laminated film objects with small ellipse array patterns to induce a larger uniaxial anisotropy so as to maximize their operating frequency.

• Journal of the Korean Magnetics Society
• /
• v.6 no.5
• /
• pp.323-328
• /
• 1996

NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$) trilayers were formed on the $4^{\circ}$ tilt-cut Si(111) substrate by rf magnetron sputtering method. With a Cu($50\;{\AA}$) underlayer, NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$) trilayers developed in-plane magnebc anisotropy and in-plane perpendicular alignment of easy axes in two magnetic components of NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$) trilayers has been found. The easy axis of Co layer consisbng of NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$) trilayers turned out to be along $4^{\circ}$ tilt Si <112> direcbon and that of NiFe layer along Si <110> direction. [NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$)]/Cu($50\;{\AA}$)/Si(111, $4^{\circ}$ tiIt-cut) trilayers showed about 2.2 % MR ratio at room temperature and large plateau in MR curves, which are more improved MR characteristics than those in [NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$)]/Cu($50\;{\AA}$)/glass trilayers with no appreciable magnetic anisotropy.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2014.11a
• /
• pp.122-123
• /
• 2014

• Proceedings of the Korean Magnestics Society Conference
• /
• 1998.05a
• /
• pp.110-111
• /
• 1998