• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.2
• /
• pp.149-159
• /
• 1999

본 연구에서는 고유진동수를 사용하여 균열의 위치와 크기를 발견하는 비파괴 균열발견모델을 유도하고 Euler-Bernoulli 보를 대상으로 이 모델의 적합성을 검증하였다. 먼저, 균열위치예측모델과 균열크기예측모델로 이루어진 균열발견체계를 제시하였는데, 균열위치예측모델은 모드민감도와 고유진동수 사이의 선형적인 관계로부터 간접적으로 유도되었으며 균열크기예측모델은 균열발생에 의한 변형에너지의 손실을 진동특성치의 변화와 비교하는 동적 파괴역학적 방법으로부터 유도되었다. 다음으로, 기존에 발표된 양단-자유보에 대한 진동모드 실험결과를 사용하여 균열위치와 균열크기를 예측하고 평가하므로 균열발견모델의 적합성과 적용성을 실험적으로 검토하였다. 대부분의 손상시나리오에서 균열위치와 균열크기 예측치는 실제값과 근사하게 일치하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1D
• /
• pp.57-65
• /
• 2008

Joint of concrete pavement contributes to improvement of pavement performance by preventing occurrence of random cracking due to drying shrinkage and temperature changes of concrete slabs at early age. However, saw-cutting operations performed prior to sufficient concrete hardening develop micro-cracking of the concrete near the joints, which may develop to long-term distresses due to repetitious traffic and environmental loadings. To reduce the distresses, the joint crack inducers with heights of 100 mm, 150 mm, and 220 mm and the joint cracking slots with various depth were installed at a test section to investigate occurrence of the joint cracks and their behaviors over 5 months. As the results, higher efficiency of the crack inducing and larger behavior of the joint cracks were observed for the taller joint crack inducer. Higher efficiency of the crack inducing and improvement of the joint performance are warranted by additional investigation and reformation of the joint crack inducer.

• Tunnel and Underground Space
• /
• v.21 no.3
• /
• pp.235-243
• /
• 2011

In this study, a control blast method, which utilizes crack guide holes, is suggested to achieve smooth fracture plane and minimize blast damage zone (BDZ) in smooth blasting. In order to verify the effectiveness of crack guide holes on the fracture plane control in blasting, fracture process analyses which consider regular smooth blasting and guide hole smooth blasting had been conducted and the fracture planes resulting from the analyses had been compared. The analyses models considered the ignition of the blast holes using detonation cords and each guide hole placed between blast holes. From the results, the smooth blasting utilizing guide holes showed lower fracture plane roughness than regular smooth blasting method in the hole spacing range between 20 to 40cm.

• The Journal of Engineering Geology
• /
• v.29 no.4
• /
• pp.405-415
• /
• 2019

The cracks induced by hydraulic rock splitting technique are formed in the direction parallel to the free plane, which is perpendicular to the minimum principal stress of the ground, or is affected by the pre-existing microcracks. In this study, the hydraulic rock splitting experiments were conducted in which the guide slot was engraved in the direction parallel to the borehole axis on the biotite granite slope, and the hydraulic pressure was injected through the double packer pressure and interval section. The test results show that the cracks along with the guide slots were induced either by the double packer pressurization or the injection of hydraulic pressure into interval section, some cracks extended across the boreholes. Therefore, the hydraulic rock splitting test is expected to control efficiently the induced cracks if the guide slots are engraved in the direction of splitting and a big flow rate is applied.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.37 no.1
• /
• pp.44-49
• /
• 2017

본고에서는 열유도 적외선 열화상 기법의 원리와 응용에 있어 기초적인 개념, 특정 상태량 및 실험적 기법에 대하여 소개하도록 한다. 유도 열화상 기법에 적용되는 유도 주파수의 범위는 1500 Hz ~ 52 MHz이며 강자성 강재 단조 부품의 표면결함 검출에 사용되어진다. 균열 검출 감도는 자분탐상기법과 유사하나 필요한 경우 유도 주파수를 낮춤으로서 강재에 숨겨진 결함을 검출할 수 있다. 탄소섬유강화폴리머(CFRP)에서는 섬유 결함을 검출하며, 실리콘 태양 전지에서는 양호한 열적 콘트라스트와 함께 균열을 검출한다. 유도 열화상 기법의 향 후 대표적인 활용분야로는 레일 및 휠과 같은 철도 구성요소에서의 결함 탐상이 있다[1].

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1552-1560
• /
• 1990

A general form of the mathematical function in the fatigue crack growth rate law for CT specimens was determined by means of the dimensional analysis at elevated temperatures. The experimental results can be rigorously described by the combination of rate theory and fracture mechanics. The rate theory approach extends the scope of fracture mechanics through the consideration of the temperature. The fatigue crack growth rates are represented by the Arrhenius type equation. This equation explains fairly well the experimental data for Cr-Mo-V rotor steel and A517-F steel in the comparatively wide temperature regions as affected with the temperature and the stress intensity factor range interaction.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.5
• /
• pp.189-196
• /
• 1997

본 연구에서는 유한요소법을 이용한 콘크리트 인장균열의 발생 및 전파양상을 모형화하기 위하여 분산균열(smeared crack) 모델의 일종인 2차원 균질화된 균열(homogenized crack)모형을 제안하였다. 제안한 모형은 인장균열면을 따라 속도 불연속계(velocity discontinuity)를 도입하고 평형방정식 빛 적합방정식을 이용하여 인장균열을 포함한 콘크리트의 구성방정식을 유도할 수 있으며 인장균열이 소성연화거동을 하는 경우. 유한요소망내에서 객관성이 유지될 수 있음을 밝히기 위하여 1차원 영역내에서 엄밀해를 유도하였다. 제안한 모형을 이용한 1차원 또는 2차원 유한요소 해석은 기존의 노치를 포함한 콘크리트 시편에 대한 실험과 상응하는 결과를 보였을 뿐만 아니라 유한요소망의 객관성이 유지되고 있음을 밝혔다. 제안한 모형은 큰 어려움없이 3차원 영역으로 확대할 수 있을 것이며 이에 대한 추가적인 연구가 계속될 것이다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.3
• /
• pp.15-22
• /
• 2003

The fatigue crack growth model is derived and the retardation model is proposed. The fatigue crack growth model considers the residual plastic stretch on the crack surface which results from the plastic deformation at the tip of fatigue crack. The fatigue crack growth rate is calculated by using the cumulative fatigue damage and plastic strain energy in the material elements at the crack tip. This model gives the crack growth rate in reasonable agreement with test data for aluminum alloy AL6061-T651 and 17-4PH casting steel. The fatigue crack growth retardation model is based on the residual plastic stretch produced from a tensile overload which reduced the plastic strain range of the following load cycles. A strip-yield model of a crack tip plasticity is used for the calculation of a plastic zone size. The proposed retardation model characterized the observed features and delayed retardation of the fatigue crack growth under tensile overload.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.701-708
• /
• 2010

The stress and displacement fields of a permeable propagating crack in orthotropic piezoelectric materials under anti-plane shear mechanical load and in-plane electric load are analyzed. The equations of motion for the propagating crack in piezoelectric materials are developed and the solution on the stress and the displacement fields through an asymptotic analysis was obtained. The influences of the piezoelectric constant and of the dielectric permittivity on the stress and displacement fields at the crack tip are explicitly clarified. Using the stress and displacement fields obtained in this study, the characteristics of stress and displacement at a propagating crack tip in piezoelectric materials are discussed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.98-105
• /
• 2018

Cracks in RC members occurred as a result of material and structural factors. The crack width and a crack location are very difficult to examine. A direct crack control method and indirect crack control method to control a crack are presented in the KHBDC (LSD) and KSCDC (2012). In the KSCDC text, cracks are controlled by steel spacing indirectly under a service load. On the other hand, in the KSCDC appendix, cracks are controlled by a crack width directly under a sustained load. In particular, the loading state considered is different. On the other hand, cracks are controlled under a combination of service load and an effective elastic modulus is used in KHBDC. Therefore, in this study, an effective elastic modulus that can reflect the ratio of the sustained load and live load was applied, and a maximum steel spacing was calculated through a design crack width. A variable interpretation was carried out, and a rational crack control method was assessed. As a result, a steel spacing through the design crack width in the KSCDC was smaller than that from the design crack width in the KHBDC, which leads to a conservative design. In addition, the maximum steel spacing suggested in this study has a consistency eliminating the difference between direct crack control and indirect crack control.