• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.97-97
• /
• 2015

전 세계적으로 화석연료의 고갈 및 환경오염 문제를 해결하기 위해 신재생에너지에 대한 관심이 급증하고 있다. 이러한 신재생에너지에는 수소 에너지, 자연 에너지(태양열, 지열 등), 바이오 매스 에너지 등이 포함된다. 이 중 수소 에너지는 지구상에 풍부하게 존재하고 있는 물과 탄화수소로부터 얻어지며, 연소 시에도 다시 물을 형성하여 오염 물질을 배출하지 않는 차세대 무공해 에너지원으로써 주목을 받고 있다. 수소 제조를 위한 공정에는 수증기 개질 공정(steam reforming), 부분 산화(partial oxidation) 및 자열개질(autothermal reforming) 등이 있으며 실제로 생산되는 대부분의 수소는 탄소/수소비(1:4)가 높은 메탄($CH_4$) 가스를 이용한 메탄 수증기 개질 공정(steam methane reforming)을 통하여 제조된다. 이 때 수소 제조의 고효율화 및 저비용화를 위해서는 반응물에 대한 높은 선택도, 고활성도 및 높은 안정성을 갖는 촉매가 반드시 필요하며, 대표적으로 Ni, Pt, Ru 등이 보고되고 있다. 이러한 촉매들은 대부분 세라믹 pellet 형태로 제작되어 왔으나 열전도도가 낮고 물리적 충격에 취약하다는 단점이 존재한다. 따라서 우리는 이러한 단점을 극복하고, 촉매의 활성을 높이기 위하여 다공성 금속 합금 폼을 촉매 지지체로 도입하였다. 또한, 다공성 금속 합금 폼 표면에 촉매의 분산 및 안정성을 향상시키기 위해 지지체와 촉매 사이에 원자층 증착법을 이용하여 inter-layer를 도입하였다. 이들의 구조, 형태, 및 표면의 화학적 상태는 주사전자현미경, EDS (energy dispersive spectroscopy)가 탑재된 주사전자현미경, X-선 회절, 및 X-선 광전자 분광법을 이용하여 규명하였다. 더하여 정전압-전류 측정법 및 유도 결합 플라즈마 분광 분석기을 이용하여 전기 화학 반응을 유도하고, 반응 후 전해질의 성분분석을 통해 촉매와 지지체 간의 안정성을 평가하였다. 따라서 본 결과들은 한국진공학회 하계정기학술대회를 통해 좀 더 자세히 논의될 것이다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.135-136
• /
• 2009

The etching characteristics of Zinc Oxide (ZnO) and etch selectivity of ZnO to $SiO_2$ in $BCl_3/Ar/Cl_2$ plasma were investigated. It was found that ZnO etch rate shows a non-monotonic behavior with increasing both Ar fraction in $BCl_3$ plasma, RF power, and gas pressure. The maximum ZnO etch rate of 53 nm/min was obtained for $BCl_3$(16 sccm)/Ar(4 sccm)/$Cl_2$(3 sccm) gas mixture. The chemical state of etched surfaces was investigated with X-ray photoelectron spectroscopy (XPS). From these data, the suggestions on the ZnO etch mechanism were made.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.74-74
• /
• 2009

Titanium nitride has been used as hardmask for semiconductor process, capacitor of MIM type and diffusion barrier of DRAM, due to it's low resistivity, thermodynamic stability and diffusion coefficient. Characteristics of the TiN film are high intensity and chemical stability. The TiN film also has compatibility with high-k material. This study is an experimental test for better condition of TiN film etching process. The etch rate of TiN film was investigated about etching in $BCl_3/Ar/O_2$ plasma using the inductively coupled plasma (ICP) etching system. The base condition were 4 sccm $BCl_3$ /16 sccm Ar mixed gas and 500 W the RF power, -50 V the DC bias voltage, 10 mTorr the chamber pressure and $40\;^{\circ}C$ the substrate temperature. We added $O_2$ gas to give affect etch rate because $O_2$ reacts with photoresist easily. We had changed $O_2$ gas flow rate from 2 sccm to 8 sccm, the RF power from 500 W to 800 W, the DC bias voltage from -50 V to -200 V, the chamber pressure from 5 mTorr to 20 mTorr and the substrate temperature from $20\;^{\circ}C$ to $80\;^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.10 no.3
• /
• pp.179-183
• /
• 2000

The reactive ion etching process of GaN using $BCI_3/H_2/Ar$ high density inductively coupled plasma was investigated. Results showed that both of the etch rate and the sidewall verticality significantly increased as the ICP power, bias voltage, and the $BCI_3$ ratio were increased whereas effects of the other variables were minimal. The maximum etch rate of about 175nm/min was obtained at the condition of ICP power 900W, bias voltage 400V, 4mTorr, and 60% $BCI_3$, which resulted in reasonably smooth etched surface. Etch residues were observed in the case of samples etched at the low bias conditions, which were proposed to be as the $GaCI_x$ compounds.

• Korean Journal of Materials Research
• /
• v.24 no.12
• /
• pp.694-699
• /
• 2014

We report the chemical vapor deposition growth characteristics of graphene on various catalytic metal substrates such as Ni, Fe, Ag, Au, and Pt. 50-nm-thick metal films were deposited on $SiO_2/Si$ substrates using dc magnetron sputtering. Graphene was synthesized on the metal/$SiO_2$/Si substrates with $CH_4$ gas (1 SCCM) diluted in mixed gases of 10% $H_2$ and 90 % Ar (99 SCCM) using inductively-coupled plasma chemical vapor deposition (ICP-CVD). The highest quality of graphene film was achieved on Ni and Fe substrates at $900^{\circ}C$ and 500 W of ICP power. Ni substrate seemed to be the best catalytic material among the tested materials for graphene growth because it required the lowest growth temperature ($600^{\circ}C$) as well as showing a low ICP power of 200W. Graphene films were successfully grown on Ag, Au, and Pt substrates as well. Graphene was formed on Pt substrate within 2 sec, while graphene film was achieved on Ni substrate over a period of 5 min of growth. These results can be understood as showing the direct CVD growth of graphene with a highly efficient catalytic reaction on the Pt surface.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.88-88
• /
• 2003

Optical Emission Spectroscopy(OES) is a very important technology for real-time monitoring of plasma in a reactor during dry etching process. OES technology is non-invasive to the plasma process. It can be used to collect information on excitation and recombination between electrons and ions in the plasma. It also helps easily diagnose plasma intensity and monitor end-point during plasma etch processing. We studied high density planar inductively coupled BCl$_3$ and BCl$_3$/Ar plasma with an OES as a function of processing pressure, RIE chuck power, ICP source power and gas composition. The scan range of wavelength used was from 400 nm to 1000 nm. It was found that OES peak Intensity was a strong function of ICP source power and processing pressure, while it was almost independent on RIE chuck power in BCl$_3$-based planar ICP processes. It was also worthwhile to note that increase of processing pressure reduced negatively self-induced dc bias. The case was reverse for RIE chuck power. ICP power and gas composition hardly had influence on do bias. We will report OES results of high density planar inductively coupled BCl$_3$ and BCl$_3$/Ar Plasma in detail in this presentation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.10
• /
• pp.785-791
• /
• 2001

High dielectric (Ba, Sr) TiO$_3$ thin films were etched in an inductively coupled plasma (ICP) as a function of Cl$_2$/Ar mixing ration. Under Cl$_2$(20)/Ar(80), the maximum etch rate of the BST films was 400 $\AA$/mim and selectivities of BST to Pt and PR were obtained 0.4 and 0.2, respectively. Etching products were redeposited on the surface of BST and resulted in varying the nature of crystallinity. Therefore, we investigated the etched surface of BST by x-ray photoelectron spectroscopy (XPS) atomic force microscopy (AFM) and x-ray diffraction (XRD). From the result of XPS analysis, we found that residues of Ba-Cl and Ti-Cl bonds remained on the surface of the etched BST for high boiling point. The morphology of the etched surfact was analyzed by AFM. A smoothsurface(roughness ~2.8nm) ws observed under Cl$_2$(20)/Ar(80), rf power of 600 W, dc bias voltage of -250 V and pressure of 10 mTorr. This changed the nature of the crystallinity of BST. From the result of XRD analysis, the crystallinities of the etched BST film under Ar only and Cl$_2$(20)/Ar(80) were maintained as similar to as-deposited BST. However, intensity of BST(100) orientation under Cl$_2$ only plasma was abruptly decreased. This indicated that CI compounds were redeposited on the etched BST surface and resulted in changed of the crystallinity of BST during the etch process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.2
• /
• pp.93-98
• /
• 2001

YMnO$_3$ films are excellent gate dielectric materials of ferroelectric random access memories (FRAMs) with MFSFET (metal -ferroelectric-semiconductor field effect transistor) structure because YMnO$_3$ films can be deposited directly on Si substrate and have a relatively low permittivity. Although the patterning of YMnO$_3$ thin films is the requisite for the fabrication of FRAMs, the etch mechanism of YMnO$_3$ thin films has not been reported. In this study, YMnO$_3$thin films were etched with Cl$_2$/Ar gas chemistries in inductively coupled plasma (ICP). The maximum etch rate of YMnO$_3$ film is 285$\AA$/min under Cl$_2$/(Cl$_2$+Ar) of 1.0, RF power of 600 W, dc-bias voltage of -200V, chamber pressure of 15 mTorr and substrate temperature of $25^{\circ}C$. The selectivities of YMnO$_3$ over CeO$_2$ and $Y_2$O$_3$ are 2.85, 1.72, respectively. The selectivities of YMnO$_3$ over PR and Pt are quite low. Chemical reaction in surface of the etched YMnO$_3$ thin films was investigated with X-ray photoelectron spectroscopy (XPS) surface of the selected YMnO$_3$ thin films was investigated with X-ray photoelectron spectroscopy(XPS) and secondary ion mass spectrometry (SIMS). The etch profile was also investigated by scaning electron microscopy(SEM)

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.4
• /
• pp.56-62
• /
• 1999

In this study, (Ba, Sr)$TiO_3$ thin films were etched with $Cl_2$/Ar gas mixing ratio in an inductively coupled plasma (ICP) by varying the etching parameter such as rf power, dc bias voltage, and chamber pressure. The etch rate was 56 nm/min under $Cl_2$/($Cl_2$+Ar) gas mixing ratio of 0.2, rf power of 600 W, dc bias voltage of 250 V, and chamber pressure of 5 mTorr. At this time, the selectivity of BST to Pt, $SiO_2$ was respectively 0.52, 0.43. The surface reaction of the etched (Ba, Sr)$TiO_3$ thin films was investigated with X-ray photoelectron spectroscopy (XPS). Ba is removed by chemical reaction between Sr and Cl to remove Sr. Ti is removed by chemical reaction such as $TiCl_4$ with ease. The results of secondary ion mass spectrometer (SIMS) analysis compared with the results of XPS analysis and the results were the same.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.5
• /
• pp.335-340
• /
• 2013

In this study, the plasma etching of the TaN thin film with $CH_4/BCl_3/Ar$ gas chemistries was investigated. The etch rate of the TaN thin film and the etch selectivity of TaN to $SiO_2$ was studied as a function of the process parameters, including the amount of $CH_4$. X-ray photoelectron spectroscopy (XPS) and Field-emission scanning electron microscopy (FE-SEM) was used to investigate the chemical states of the surface of the TaN thin film.