• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.2
• /
• pp.627-635
• /
• 2014

Currently the highest speed limit on the road traffic congestion or because you can not cope with climate change to cause a traffic accident may be a factor. According to the Road Traffic Act as well as 20% to 50% in case of inclement weather, but the driver must slow speed left to the judgment of the difficulties, and to slow the vehicle and the relative velocity between the vehicle does not run longer be a big influence on the environment and safety. Thus, variable speed control for drivers on the road, specify the appropriate maximum speed limit in bad weather It keeps motorists slowed the run rate to prevent accidents or reduce the severity of accident damage is expected to be possible. The purpose of this study is the frequent traffic accidents Continuous Busan (City Freeway) around the variable speed control in the appropriate sections so that it can be done by analyzing the characteristics of traffic accidents were the severity of the accident. Highway and urban environment, the geometry of the structure because it has a lot of Curved planar point compared to wet and dry road surfaces by simulated rain wet had bom the more the speed the greater the risk of an accident was the result. Based on these results, the primary section, first urban highway tunnel, near the lamp, near Toll Plaza, near binary Outlet after considering various factors such as speed reduction is needed in the first period by conducting awareness and recognize the need for the participation of the driver and the future city installation and operation of highways in all sectors is expected to be expanded.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.2
• /
• pp.116-127
• /
• 2017

A fog on road is known as a weather factor that affects traffic flow. The method in order to solve the problem, recently, Variable Speed Limit(VSL) which provide reasonable speed limit by road and weather conditions in real time is introduced. However, if drivers do not comply with VSL, the road safety more decrease than without VSL because individual vehicle's speed deviation is larger than without VSL. Therefore, this paper aims to analyze to speed limit compliance and traffic characteristics under foggy conditions with and without VSL. A test using driving simulator divides into normal and foggy condition with visibilities are 200m, 150, 50~100m. The test results showed that 70 subjects's average speed mostly obeyed speed limit, but speed deviation generally declined with VSL. Especially, the speed deviation more reduced under foggy conditions. According to this study, compliance of VSL clearly rose in low visibility and VSL helped improve road safety due to reduction of speed deviation. The results of this study are expected to make use of reasonable speed limit for reference.

• Clinical and Experimental Pediatrics
• /
• v.53 no.2
• /
• pp.248-252
• /
• 2010

Anomalous origins of coronary arteries are a rare type of disease among children. These anomalies can be categorized into 3 types according to the anatomical relationship of the aorta and pulmonary trunks. Among these types, the interarterial type, as observed in our case, needs early diagnosis and treatment, because it can increase the risk for the patient, causing sudden cardiac death in young individuals. Although there are controversies concerning the management of anomalous origins of the left coronary artery (LCA) in children, the result can be very beneficial, if treated accurately. Three well-known methods for correction of anomalous origins of LCA are re-implantation, coronary arterial bypass grafting (CABG), and unroofing. We report on the case of a 12-year-old girl who had chest discomfort and syncope with physical exercise and was later diagnosed with an anomalous origin of LCA by transthoracic echocardiography (TTE) and heart computed tomography (CT). She underwent a corrective operation by re-implantation, CABG, and unroofing.

• Journal of the korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.53-68
• /
• 1996

마그네슘이 자동차 경량화에 관심이 되는 이유는 근본적으로 CAFE 규제와 같이 경량화를 통한 화석연료의 소모를 크게 억제해야 한다는 사회적인 규제이나, 지난 10여년간의 기술발전으로 내식성이 나쁘다거나 취급이 위험한 금속이라는 인식이 크게 개선된 데에도 있다. 다른 경량금속에 대한 Mg 지금 가격의 비교조건이 호전되었고 향후 원소 재공급의 다변화가 추진되고 있는 것도 환경을 변화시킨 중요한 요인이다. 그간 중요한 경량화 대체 재료로 연구투자가 많았던 유기고분자 재료 및 FRP 등과 같은 복합재료는 폐기부품의 재활용이 어려움 때문에 호나경친화적인 단점이 부각되어, 이 소재의 증가가 주춤해 있다. 마그네슘의 경우에는 재활용이 가능하고, 진동흡수효과가 매우 커서 소음발생을 크게 줄일 뿐만 아니라, 주행 및 내구성시험에서 치수안정성이 좋고 많은 종류의 전자기기 사용에 의한 전자파 차폐효과도 큰 장점을 가지고 있다. 본 고에서는 Mg 다이캐스팅으로 자동차부품의 경량화 현황과 선진국에서 보는 전망을 미국을 중심으로 정리하고, 이와 관련한 Mg 다이캐스팅으로 자동차부품의 경량화 현황과 선진국에서 보는 전망을 미국을 중심으로 정리하고, 이와 관련한 Mg 기술적인 이슈와 시장전망도 서술하였다. 그리고 현재 우리나라의 연구계와 부품업계에서 추진하고 있는 연구개발 동향을 자동차 업계에 소개하는 의미도 있다. 이처럼 우리나라의 현황을 정리해 보는 것은 국내 자동차 산업이 국제적인 경쟁을 하고 있고 Mg기술과 원료확보에서 일본의 견제를 받고 있는 우리의 현실에서도 필요한 작업으로 생각된다.값들로 구성되는 형상을 내구 성능, 성형성등을 고려하여 최종 형상으로 결정한다. 내구성능의 예측은 금속부품의 내구수명 예측에 널리 이용되고 있는 방법이 방진 고무부품의 경우에도 적용 가능한지를 검토하고, 방진 고무부품에도 일반적으로 적용될수 있는 내구수명 예측방안의 개발 가능성을 타진해 보았다. 본 연구의 목표는 시제품을 제작하기 이전에 설계된 부품에 대한 스프링 상수 및 내구특성을 체계적으로 규명하여 제품 시험의 횟수를 줄이고, 보다 정밀한 제품을 제작할 수 있도록 하기 위한 것이다.세포수는 초기 배반포기배에서 팽윤 배반포기배로 진행됨에 따라 두배에서 세배 정도 증가되었음을 알 수 있었다. 또한, differential labelling과 bisbenzimide기법에서 얻어진 각각의 총세포수를 비교하였을 때 총세포수는 발달의 진행 정도에 따라 증가되며 그와 동시에 동일한 군 간의 세포수도 거의 유사함을 알 수 있었다. 따라서, ICM과 TE를 differential labelling하는 기법은 수정란의 quality를 평가하는데 매우 유용한 기법으로서 착상전 embryo 발달을 연구하는데 효과적으로 이용될 수 있다는 것을 시사한다. 고도의 유의차를 나타낸 반면 비수구, 초생수로구 및 Bromegrass 목초구 간에는 아무런 유의차가 인정되지 않았다. 7. 농지보전 처리구인 배수구와 초생수로구는 비처리구에 비해 낮은 침두 유출량과 낮은 토양유실량을 나타내었다.구보다 14% 절감되는 것으로 나타났다.작용하는 것으로 사료된다.된다.정량 분석한 결과이다. 시편의 조성은 33.6 at%

• Journal of Korean Society of Transportation
• /
• v.30 no.2
• /
• pp.43-52
• /
• 2012

A lane departure warning system (LDWS) is an effective technology-based countermeasure for preventing traffic crashes as it provides warning information to drivers. Understanding the characteristics of perception and satisfaction levels on LDWS is fundamental for deriving better performance and functionality enhancements of the system. The purpose of this study is to evaluate the user satisfaction of LDWS. A survey to collect user perception and user preference data was conducted. Both cross-tabulation analysis and binary logistic regression technique were adopted to identify the factors affecting user satisfaction for LDWS. The results revealed that the accuracy and timeliness of warning information was significant for evaluating the effectiveness of LDWS. In particular, the warning accuracy at a curve segment on the road was the most dominant factor affecting user satisfaction. The outcome of this study would be valuable in evaluating and designing LDWS functionalities.

• Journal of Korean Society of Transportation
• /
• v.23 no.2
• /
• pp.95-106
• /
• 2005

Road accidents are considered as the result of a complex interplay between road, vehicle, environments, and human factors. Little study, however, has been carried out on the attributes of human factor compared to the road geometric conditions and traffic conditions. The previous researches focused on mainly both traffic and geometric conditions on specific location. Therefore, it's hard to explain phenomenon of the high traffic accident rates where road and traffic conditions are good. Because of these reasons, accident analysis has contributed on geometric improvement and has not contributed on traffic management such as selection of attention section, driver napping alert, etc. The freeway incident management is also associated with reliable prediction of incident occurrences on freeway sections. This paper presents a method for estimating the effect of trip length on freeway accident rate. A PAR (Potential Accident Ratio), the new concept of accident analysis, considering TLFDs (Trip Length Frequency Distributions) is suggested in this paper. This approach can help to strengthen freeway management and to reduce the likelihood of accidents.

• Journal of the Korean Society for Railway
• /
• v.19 no.4
• /
• pp.480-488
• /
• 2016

For the development of areas around railway lines, subsurface construction using the non-open cut method under the railway has recently been increased. However, when a structure under a railway is constructed, the stress release of the ground is not considered an important factor in the design. In this study, laboratory tests were conducted to determine a zone of stress relaxation. Field tests using an inclinometer were performed to measure the horizontal displacement of the ground during non-open cut construction. The stress release zone and the subgrade stiffness were investigated by numerical analysis. The results of the laboratory tests indicated that the failure zone in the ground was similar to a Rankine's active earth pressure zone. The measured data from the inclinometer in the field tests showed that displacements started when a steel pipe was pushed into the ground. The results of numerical analysis show that lateral earth pressure was also close to Rankine's active earth pressure. The roadbed support stiffness of the soil around the structure decreased to 40% of the original value. The ground around the subsurface structure constructed using nonopen cut methods should be reinforced to maintain the running stability of train.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.604-613
• /
• 2018

In recent years, numerous train derailment accidents caused by deterioration and high speed technology of railways have increased. Guardrails or barriers of railway bridges are installed to restrain and prevent the derailment of the train body level. On the other hand, it can result in a high casualties and secondary damage. Therefore, a Derailment Containment Provision (DCP) within the track at the wheel/bogie level was developed. DCP is designed for rapid installation because it reduces the impact load on the barrier and inertia force on the steep curve to minimize turnover, fall, and trespass on the other side track of the bridge. In this paper, DCP was analyzed using LS-Dyna with a parameter study as the impact loading location and interface contact condition. The contact conditions were analyzed using the Tiebreak contact simulating breakage of material properties and Perfect bond contact assuming fully attached. As a result, the Tiebreak contact behaved similarly with the actual behavior. In addition, the maximum displacement and flexural failure was generated on the interface and DCP center, respectively. The impact analysis was carried out in advance to confirm the DCP design due to the difficulties of performing the actual impact test, and it could change the DCP anchor design as the analysis results.

• Applied Chemistry for Engineering
• /
• v.32 no.4
• /
• pp.361-370
• /
• 2021

Carbon fiber reinforced polymer (CFRP) is one of the composite materials, which has a unique property that is lightweight but strong. The CFRPs are widely used in various industries where their unique characteristics are required. In particular, electric and unmanned aerial vehicles critically need lightweight parts and bodies with sufficient mechanical strengths. Vehicles using the battery as a power source should simultaneously meet two requirements that the battery has to be safely protected. The vehicle should be light of increasing the mileage. The CFRP has considered as the one that satisfies the requirements and is widely used as battery housing and other vehicle parts. On the other hand, in the battery area, carbon fibers are intensively tested as battery components such as electrodes and/or current collectors. Furthermore, using carbon fibers as both structure reinforcements and battery components to build a structural battery is intensively investigated in Sweden and the USA. This mini-review encompasses recent research trends that cover the classification of structural batteries in terms of functionality of carbon fibers and issues and efforts in the battery and discusses the prospect of structural batteries.

• Tunnel and Underground Space
• /
• v.32 no.5
• /
• pp.298-311
• /
• 2022

Some problems, such as aging workers, a decreased population due to a low birth rate, and shortage of skilled workers, are rising in construction sites. Therefore research for smart construction technology that can be improved for productivity, safety, and quality has been recently developed with government support by replacing traditional construction technology with advanced digital technology. In particular, the motor grader that mainly performs road surface flattening is a construction machine that requires the application of automation technology for repetitive construction. It is predicted that the construction period will be shortened if the construction automation technology such as trajectory tracking, automation work, and remote control technology is applied. In this study, we introduce the hardware and software architecture of the smart motor grader to apply unmanned and automation technology and then analyze the traditional earthwork method of the motor grader. We suggested the application plans for the path pattern and blade control method of the smart motor grader based on this. In addition, we verified the performance of waypoint-based path-following depending on scenarios and the blade control's performance through tests.