• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.442-442
• /
• 2011

우리나라는 홍수조절이나 통제를 목적으로 10개의 다목적댐을 통한 홍수방재시스템을 운영하고 있다. 다목적댐 또한 방류능력과 저류능력에 한계가 있기 때문에 안정적인 홍수조절을 위해서는 유입량과 유출량을 미리 예측할 수 있어야 한다. 하지만, 강수량은 그 변동이 심하여 정확한 예측이 어렵기 때문에 합리적인 하천 구조물의 설계와 홍수예측기술의 발전을 위해서는 강우-유출 해석뿐만 아니라 과거의 수문자료를 사용한 통계적인 분석이 요구된다. 최근 기후변화로 인해 과거에 겪지 않았던 이상 기후현상이 빈번하게 나타나고 있다. 기상청발표에 따르면 최근 10년간(1996~2005) 15개 지점의 평균 연강수량은 1,458.7 m로 약 10 �時貂� 하였고, 특히 여름철은 18 %로 증가폭이 가장 크며 호우일수는 30년 평균이 2일인데 비하여 2.8일로 0.8일 증가하였다. 이러한 강수량 및 호우일수 증가는 여름철 심각한 수해를 초래할 수 있다. 본 연구는 기후변화로 인한 수해를 대비하여 홍수기중 저수지 제한수위운영의 안정성을 검토하였다. 연구 대상 지역은 광교저수지로 수원천 상류부인 경기도 수원시 장안구 연무동에 위치한다. 유역면적은 10.98 km, 유효저수량은 250.0 만$m3$이며, 현재 예비취수원으로 사용되고 있다. 기후변화에 따른 하류지역의 예상치 못한 홍수피해를 사전에 예방하기 위해 광교저수지 유역의 설계 강수량과 설계 홍수량을 산정하였다. 제한수위의 시나리오는 현재 시행중인 제한수위와 만수위를 포함하여 5개로 설정하였다. 설계 홍수량이 광교저수지로 유입될 때 시나리오에 따른 월류량은 웨어공식을 이용하여 산정하였으며 결론은 다음과 같다. 1. 39년간의 최다 일 강수량 자료를 사용하여 100년 빈도의 설계 강수량을 Gumbel 분포법으로 산정한 결과 344.4 mm임을 알 수 있었다. 2. 광교저수지 유역의 설계 홍수량을 SCS 방법을 이용하여 산정한 결과 $216.2\;m^3/s$/s로 나타났으며, 총 유입량은 $301.0\;m^3$/day로 파악되었다. 3. 광교저수지로 설계홍수량이 유입될 때 제한수위 시나리오에 따른 최대 방류량은 EL. 87 m의 경우 $23.1\;m^3/s$, EL. 89 m의 경우$27.5\;m^3/s$ EL. 91.36 m의 경우 $79.6\;m^3/s$, EL. 93 m의 경우 $121.1\;m^3/s$ EL. 95.2 m의 경우 $137.`\;m^3/s$이다. 광교저수지 하류부분의 하천정비기본계획상의 설계 홍수량은 $114\;m^3/s$로 홍수기중 저수지의 제한수위는 EL. 91.36 m이하로 설정하는 것이 바람직한 것으로 판단된다.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.44 no.5
• /
• pp.739-745
• /
• 2015

To maintain quality of Delaware grapes during storage, grape samples were treated with 0.1% chitosan dissolved in 0.5% acetic acid, packaged with low density polyethylene film, and stored at 4 or $20^{\circ}C$ for 12 days. Chitosan treatment reduced initial populations of yeast and molds in grapes by 1.86 log CFU/g compared to that of the control. During storage, oxygen contents in packages of samples decreased, whereas carbon dioxide contents increased. In addition, regardless of storage temperature, changes in oxygen and carbon dioxide concentrations of grapes treated with chitosan were lower than those of the control. Hardness of samples decreased, and Hunter L, a, and b values were not significantly different among treatments. Regarding pH and total soluble content, grapes stored at $4^{\circ}C$ maintained pH and had greater total soluble content than those stored at $20^{\circ}C$. These results suggest that chitosan treatment and low temperature storage can be useful for maintaining microbiological safety and quality of Delaware grapes during storage.

• Journal of Plant Biotechnology
• /
• v.37 no.1
• /
• pp.25-46
• /
• 2010

The demand for fuel and energy resources continues to grow due to increased consumption and emerging economies in all parts of the world. With this increase in demand, crude oil prices in the international market has jumped dramatically. Global warming, which is a consequence of increasing greenhouse gas (GHG) emissions, has become scientific, social, and political concerns. To cope with global warming and energy crisis, cost-competitive biofuels are urgently needed. In addition, development of an infrastructure, which supplies energy stably and diversifies energy resources, as well as new cost-saving technologies should be developed to reduce the costs of producing biofuels. Due to high oleic acid content, rapeseed (Brassica napus L.) is currently the potential feedstock for biodiesel production in temperate zone region and the production and use of rapeseed oil is already commercialized in Europe. In Korea double-cropping (rice and rapeseed) became more prevalent because it reduces competitions from land constraints. Production of rapeseed as a biodiesel feedstock may reduce the influence of rising oil prices and nation's dependence on imported petroleum and increase job opportunities and farm incomes.

• Journal of Korea Water Resources Association
• /
• v.49 no.8
• /
• pp.657-671
• /
• 2016

It is expected that water resources will be changed spatially and temporally due to the global climate change. The quantitative assessment of change in water availability and appropriate water resources management measures are needed for corresponding adaptation. However, there are large uncertainties in climate change impact assessment on water resources. For this reason, development of technology to evaluate the uncertainties quantitatively is required. The objectives of this study are to develop the climate change uncertainty assessment method and to apply it. The 5 RCMs (HadGEM3-RA, RegCM4, MM5, WRF, and RSM), 5 statistical post-processing methods (SPP) and 2 hydrological models (HYM) were applied for evaluation. The results of the uncertainty analysis showed that the RCM was the largest sources of uncertainty in Spring, Summer, Autumn (29.3~68.9%), the hydrological model was the largest source of uncertainty in Winter (46.5%). This method can be possible to analyze the changes in the total uncertainty according to the specific RCM, SPP, HYM model. And then it is expected to provide the method to reduce the total uncertainty.

• Journal of the Korea Institute of Building Construction
• /
• v.11 no.4
• /
• pp.333-344
• /
• 2011

The recent expansion in the number of housing construction projects has been accompanied by substantial improvements in construction quality, which can be attributed to the development of new construction technologies and materials. In apartment complex construction projects, numerous mechanization technologies have been adopted as part of the floor plastering process to counter increasing difficulties in securing labor and the pressing need to reduce lead time, but these have also triggered setbacks such as additional costs or loss of time to fix cracks in or loosening of floor. Cracks developing in the floor of an apartment housing unit, in terms of materials in use, are the products of a complex combination of material makeup, construction workmanship, concrete curing and the protection method. Controlling such elements from the perspective of materials in use may ensure partial success in reducing cracks, but fall short of eliminating them completely. Any attempt to prevent cracks from developing in the first place requires systematic analysis as to their potential causes and viable solutions to reduce them. On this backdrop, this paper aims to provide an analysis of potential causes of cracks found in floor plastering, and consider the mechanism of a crack stop-bar as a fundamental safeguard against them.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.2
• /
• pp.267-274
• /
• 2018

A variety of appendages are attached to coastal and offshore fishing boats to improve stability during navigation or fishing operations (stability performance and roll reduction). These appendages are generally classified into three types, which are shown in Fig. 1. The numerical calculations were conducted for the following eight cases: one case of a bare hull, three cases where a single appendage attached, three cases of a pair of appendages attached, and one case where all three appendages were attached. Table 1 presents the main dimensions of the bare hull and Table 2 describes the main dimensions of the three appendages. The fluid dynamic performance with regard to the three hull appendages was evaluated via CFD for the following cases: each of the appendages attached independently, a pair of appendages attached, and all three appendages attached simultaneously. The No. 1 appendage showed that pressure resistance was proportionally greater than friction resistances. Both Nos. 2 and 3 appendages showed comparable levels of pressure and friction resistances. The correlation between appendages was minimal in the case of pairs and Comparing the cases of the No. 2 appendage attached and all appendages attached, at 11 kn, the EHP showed an difference of 9 %.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.1
• /
• pp.123-136
• /
• 2018

The objective of this study is to propose a new methodology to fabricate a reliable engineering-scale buffer block, which shows homogeneous and uniform distribution in buffer block density, for in-situ experiments. In this study, for the first time in Korea, floating die press and CIP (Cold Isostatic Press) are applied for the manufacture of an engineering-scale bentonite buffer. The optimized condition and field applicability are also evaluated with respect to the method of manufacturing the buffer blocks. It is found that the standard deviation of the densities obtained decreases noticeably and that the average dry density increases slightly. In addition, buffer size is reduced by about 5% at the same time. Through the test production, it is indicated that the stress release phenomenon decreases after the application of the CIP method, which leads to a reduction in crack generation on the surface of the buffer blocks over time. Therefore, it is confirmed that the production of homogeneous buffer blocks on industrial scale is possible using the method suggested in this study, and that the produced blocks also meet the design conditions for dry density of buffer blocks in the AKRS (Advanced Korea Reference Disposal System of HLW).

• Resources Recycling
• /
• v.18 no.3
• /
• pp.55-61
• /
• 2009

Dewatering process to remove water from pigment sludge was important in the diverse aspects of the improvement of product quality, curtailment of the drying cost and the transportation. It was difficult to dewater pigment particles with the mechanical forces because the size was fine under $5{\mu}m$. Thermal filter press dewatering equipment composed of squeezing plate and a fixed heating plate was developed to improve the dewaterability of pigment the sludge as supplying the heat from the fixed heating plate to the cake. Several tests that estimate the dewaterability for pigment sludge as with or without squeezing process and the difference of dewatering time was conducted with this equipment. Dewaterability of thermal dewatering under squeezing process was increased about 20% compared with non squeezing process. Under squeezing process, thermal dewatering tests changing dewatering time with 70 and 80 minute were conducted respectively. The water content of cake was more reduced at dewatering time of 80 minute compared with 70 minute, and dewatering velocity was also decreased, which caused the productivity of thermal filter press to drop. It was observed that clogging of filter cloth didn't almost occur because the liquid was discharged from cake layer easily. In this research, it was resulted that the squeezing process and long dewatering time were effective to improve the dewaterability of pigment sludge. So, this thermal filter press equipment was useful for dewatering the fine particle sludge like pigment.

• Proceedings of the Safety Management and Science Conference
• /
• 1999.11a
• /
• pp.343-343
• /
• 1999

아크용접은 산업전반에 걸쳐 그 생산기반에 없어서는 안될 필수기술로써 자동차 및 조선, 항공우주산업에 이르기까지 경제기반에 미치는 파급효과가 매우 크다. 그러나 이 아크용접을 하게 되면 각종 가스와 미세입자로 이루어진 흄이 발생하게 되는데 이들은 작업자들의 건강에 많은 영향을 미치는 것으로 보고되어 있다. 용접흄에는 용접재료 및 용접공정에 따라 다양한 유해원소가 포함되어 있고 그 종류에 따라 인체에 미치는 잠재적 독성효과도 매우 광범위하다. 최근 국내에서는 용접사들 중에 용접흄에 포함된 중금속 중 Mn중독에 의한 파킨스씨병 환자들과 Cr중독에 의하여 콧속 연골에 구멍이 뚫리는 비중격천공(鼻中隔穿孔) 환자들이 직업병으로 판정 받아 산재요양이 승인된 사례가 있다. 이러한 계기로 인하여 용접사들의 용접기피 현상이 심화되고 작업환경에 대한 법적규제는 선진 외국뿐만 아니라 국내에서도 한층 엄격하게 강화되고 있는 실정이다. 따라서 이제는 작업자와 사용자 모두 용접흄에 대한 인식의 전환이 요구되는 때이며 여러 분야에서 이러한 용접흄에 대한 연구가 활발히 진행되어야 한다. 해외에서는 이미 용접흄에 대한 연구가 활발히 진행되어 왔으나 국내의 경우는 매우 미비한 상태이며 용접산업의 미래 영향력이나 필요성을 고려할 때 국내에서도 적극적인 관심을 가져야 할 부분으로 판단된다. 본 연구에서는 아크용접공정에서 발생하는 흄의 특정 중금속 성분이 인체에 치명적인 악영향을 미치는 것에 착안하여 여러 종류의 용접재료에서 발생되는 용접흄의 중금속 분포를 조사하여 비교하였다. 이것은 향후 용접재료별 및 용접공정별 발생되는 흄의 유해원소를 저감시킬 수 있고 또한 각종 유해원소의 노출기준 및 평가기준을 마련할 수 있는 기초data로써 도움이 되리라 사료된다.동, 공정중재고가 줄어드는 결과를 보였고, 가동률 수준이 높을수록 ORR 방법간의 차이가 크게 나타났다. 그리고 부하평준화 기능은 Order Release 정책의 유효성에 별 영향을 주지 않는 것으로 나타났다. 결론적으로, Order Release 방법은 우선순위규칙간의 성능차이를 줄이거나, 대체할 수 통제 기법이라기보다는 우선순위규칙을 보완하여 공정중재고와 작업현장에서의 리드타임, 리드타임의 편차를 줄여주는 역할을 한다고 볼 수 있다. 그리고, 계획시스템이 존재하여 계획오더가 일정기간간격으로 이송되는 환경에서 특히 유용하다는 결론을 얻었다. 알 수 있었다. 것인데, 제조업에서의 심각한 고비용, 저효율 문제 를 해결하기 위해 필수적으로 도입해야만 하는 실정이다. 또한 소비자의 다양한 요구로 인 하여 제품의 종류와 사양면에서 심한 변동을 보이는 시장 수요에, 신속한 정보처리로 대응 하는데도 크게 기여하고 있다. 이에 본 연구에서는, 자동차 Job Shop의 동기화 생산방식을 지원하는 동기화 생산시스템의 구축 모델을 제시하고자 한다.과로 여겨지며, 또한 혈청중의 ALT, ALP 및 LDH활성을 유의성있게 감소시키므로서 감잎 phenolic compounds가 에탄올에 의한 간세포 손상에 대한 해독 및 보호작용이 있는 것으로 사료된다.반적으로 홍삼 제조시 내공의 발생은 제조공정에서 나타나는 경우가 많으며, 내백의 경우는 홍삼으로 가공되면서 발생하는 경우가 있고, 인삼이 성장될 때 부분적인 영양상태의 불충분이나 기후 등에 따른 영향을 받을 수 있기 때문에 앞으로 이에 대한 많은 연구가 이루어져야할 것으로 판단된다.태에도 불구하고 [-wh]의미의 겹의문사는 병렬적 관계의 합성어가 아니라 내부구조를 지니지 않은 단순한 단어(min

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.3
• /
• pp.96-106
• /
• 2014

Necessarily traffic policies have been biased in car than pedestrian, so pedestrian's environment is getting worse. Result of this situation our accident rate is high as 36.4%, compared to OECD member countries with average rate of 17.8%(in 2009). Increasing interest for pedestrians environment improvement, and it make an effort to build environment to guarantee walk and safety of pedestrians. Analysis on the binary logistic regression(BLR) was used. The dependent variable is occurring from the road width of less than 9m accident, and independent variable extracted can be obtained from the traffic accident data. Traffic accident on roads having width of less than 9 meters affecting variables is when the driver is straight, when the driver is female, when the pedestrian is walk driveway, and so on. To prevent it, efforts is demanded to protect handicapped, to build safe pedestrians environment using C-ITS and to decrease speed of going straight vehicle on roads having width of less than 9 meters.