• 제목/요약/키워드: 원심 압축기

검색결과 192건 처리시간 0.04초

지열 히트 펌프시스템용 터보 압축기 개발 (Development of the Turbo Compressor for a Geothermal Heat-Pump System)

  • 박준영;박무룡;최상규;윤의수;황순찬
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2004년도 추계학술대회
    • /
    • pp.1395-1400
    • /
    • 2004
  • A centrifugal compressor for geothermal heat pump system using R134a as working fluid has been developed. The centrifugal compressor consists of an impeller with splitters, two vaneless diffuser, a low solidity vaned diffuser and a volute. In this compressor, diffuser blade angles are controlled to satisfy both heating and cooling conditions. A aerodynamic design was done by applying the repeating design procedure including a meanline design, a 3D geometry generation and fluid dynamic calculation. In this paper, design and performance prediction results of the compressor are presented.

  • PDF

차량용 가변용량 압축기의 사판 거동에 관한 연구 (A Study on the Swash Plate Behavior of Variable Displacement Compressor for Automotive Air Conditioning System)

  • 이태진;이건호
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2004년도 추계학술대회
    • /
    • pp.1335-1340
    • /
    • 2004
  • Due to the distinct advantages of comfort, drive ability and fuel economy standard, the variable displacement swash plate type compressor which can control the compressor displacement by increasing or reducing the swash plate angle has been developed for automotive air-conditioning system. That can be obtained constant temperature of car room on the variation cooling capacities or engine speeds. This paper was carried out the analysis of swash plate behavior to obtain the forces and moments applied to the swash plate and to get the variable controlability on the variation of compressor speeds and swash plate chamber pressures. The results of simuation agree very well with the experimental data.

  • PDF

서지 마진 증가를 고려한 원심 압축기 설계 최적화 (A Study on Centrifugal Compressor Design Optimization for Increasing Surge Margin)

  • 최재호
    • 한국유체기계학회 논문집
    • /
    • 제11권2호
    • /
    • pp.38-45
    • /
    • 2008
  • This study presents a numerical procedure to optimize the compressor design to increase the surge margin of compressor with response surface method (RSM). The Box-Behnken design method is used to reduce the number of calculation for fitting the second-order response surface. In order to consider the increase of surge margin during numerical optimization without any calculation at the surge point, the slope of compressor characteristic curve at the design point is suggested as an objective function in the present optimization problem. Mean line performance analysis method is used to get the design and off-design characteristic curves of centrifugal compressor. The impeller exit angle, impeller exit height and impeller radius are chosen as design variables. The optimum shapes show the increase of surge margin for the surge margin optimization and increase of efficiency for the efficiency optimization in comparison with an initial shape.

자동차용 터보차저의 오버헝 압축기 볼류트의 두 형태에 대한 유동장 특성 (Flow Characteristics of Two Types of Overhung Compressor Volute for Automobile Turbocharger)

  • ;이근식
    • 대한기계학회논문집B
    • /
    • 제38권1호
    • /
    • pp.25-30
    • /
    • 2014
  • 자동차용 터보차저 원심압축기의 오버헝 볼류트의 두 가지 타입에 대한 유동장 특성이 수치적으로 연구되었다. 볼류트의 성능을 높이기 위해서는 높은 압력회복계수와 낮은 손실계수를 갖도록 함이 필요하다. 본 연구에서는 디퓨저 입구각을 $24^{\circ}$, 질량유량을 0.055 kg/s 로 유지하고 두 가지 타입의 오버헝 볼류트에 대한 유동장 특성을 조사하였다. 하나는 1 개의 원호로 이루어진 볼류트 단면(타입 1)이며, 다른 하나는 3 개의 원호로 이루어진 볼류트 단면(타입 2)이다. 타입 2 볼류트가 타입 1 볼류트 보다 원주방향 전체를 통틀어 높은 압력회복계수와 낮은 손실계수를 보여주었다.

분리축방식 터보축 엔진의 정상상태 모사 및 실험연구 (A Steady-State Simulation and Experimental Study of Turboshaft Engine with Free Power Turbine)

  • 공창덕;기자영;고광웅
    • 한국추진공학회지
    • /
    • 제1권2호
    • /
    • pp.84-90
    • /
    • 1997
  • 다목적으로 활용할 수 있는 분리축방식의 터보축 엔진 개발을 위한 정상상태 해석 프로그램의 개발과 함께 동일한 형식의 가스터빈엔진 시험장치를 이용한 실험을 통해 프로그램의 해석결과와 비교, 그 타당성을 입증하였다. 실험에 이용된 시험장치는 1단 원심형 압축기, 인통형 연소기, 1단 원심형 압축기 터어빈 및 동력 터어빈으로 구성되어 있으며 출력은 3상 교류발전기를 통해 획득된다. 해석에 사용된 주요 구성품의 성능곡선은 시험장치 제작자로부터 획득된 자료를 이용하였으며, 경우에 따라 시험장치를 이용한 실험을 통하여 보정하였다. 시험장치를 이용한 실험결과를 프로그램 해석결과와 비교한 결과, 시험장치의 운용제한에 의해 실제 작동영역이 제한되기는 했으나, 압력비, 출력 등 주요 변수들에서 6% 미만의 오차를 보였다.

  • PDF

터보 압축기 성능시험을 위한 계측기기 선정 (Instrumentation for Performance Test of Turbo Compressor)

  • 박태춘;강영석;양수석
    • 항공우주기술
    • /
    • 제7권2호
    • /
    • pp.46-52
    • /
    • 2008
  • 5MW급 발전용 가스터빈의 주요 구성품 중 압축기에서의 성능시험 및 해석을 위해 측정 파라미터와 그 파라미터를 계측하기 위한 센서류를 선정하고자 한다. 축류압축기의 경우 각 단의 케이싱에서 정압 분포를 평균하여 계측하고, 내부 유동장에서 Kiel 온도관을 이용하여 전압 및 전온도 분포를 계측한다. 원심압축기의 경우 임펠러 출구의 허브면과 팁면에서의 정압 분포는 일반적으로 상당한 차이가 존재하므로 각 면에서 정압을 측정하여 평균하고, 디퓨저 내부와 디스월러 내부에서의 정압 분포를 계측하기 위해 한 피치에서 5개의 유선을 따라 10 곳에서 정압을 측정하고자 한다. 또한 압축기 내 유동특성과 동익-정익간의 상호작용을 고찰하기 위해 5공 피토관을 이용하여 내부 상세유동을 계측한다.

  • PDF

재순환케이싱처리 높이변화가 터보차저 압축기의 성능에 미치는 영향 (Effect of Height Variation of Recirculating Casing Treatment on the Performance of a Turbocharger Compressor)

  • ;;이근식
    • 대한기계학회논문집B
    • /
    • 제39권8호
    • /
    • pp.669-675
    • /
    • 2015
  • 자동차용 터보차저 원심압축기의 재순환케이싱처리(RCT)부의 높이변화가 압축기의 성능에 미치는 영향이 조사되었다. 연구대상 RCT 부의 높이는 1.2mm, 1.5mm, 1.8mm 의 세가지이며, 회전수 범위는 90,000 - 150,000 rpm, 유량 범위는 0.015 kg/s - 0.08 kg/s 이다. 전압력비와 등엔트로피 효율 비교 결과, 본 수치계산은 실제압축기의 성능 제원과 최대오차 0.7%의 범위 내에서 잘 일치하였다. 해석결과, RCT 부 높이 1.2mm, 1.8mm, 1.5mm 순서로 균일 압력분포, 높은 압력비, 넓은 작동범위를 얻었다. 이들 세가지 경우 모두, 회전수가 증가할수록 이들의 압력비는 높아지나 운전범위는 좁아지는 전형적인 압축기 맵의 특성을 보여주었다.

원심 압축기 볼루트 성능 해석 (Numerical Study on Performance of Centrifugal Compressor Volute)

  • 김우준;오창훈;조경석
    • 유체기계공업학회:학술대회논문집
    • /
    • 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
    • /
    • pp.539-542
    • /
    • 2006
  • A volute (or scroll) of a centrifugal compressor collects the flows from impeller or diffuser, and passes it to a pipe at the exit. This flow still contains some kinetic energy which is not converted into pressure at diffuser, thus volute designer must concern the way to minimize losses. This study defines some variables which determine the shape of volute, and carry out computational analysis based on Design of Experiment to optimize the performance of volute.

  • PDF

벌류트 압축기내의 난류유동 수치해석 (Numerical Analysis of Turbulent Flows in the Scroll Volute of Centrifugal Compressor)

  • 곽승현
    • Journal of Advanced Marine Engineering and Technology
    • /
    • 제31권6호
    • /
    • pp.681-686
    • /
    • 2007
  • The flow analysis was made by applying the turbulent models in the scroll volume of centrifugal compressor. The $k-{\varepsilon}.\;k-{\omega}$, Spalart-Allmaras and reynolds stress models are used in which the hybrid grid is applied for the simulation. The velocity vector the Pressure contour. the change of residual along the iteration number. and the dynamic head are simulated by solving the Navier-Stokes equations for the comparison of four example cases.