• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.85.1-85.1
• /
• 2005

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.341-344
• /
• 2009

본 연구에서는 허브 대 팁의 비가 큰 원심형 압축기의 성능시험을 수행하였으며, 이를 수치해석 결과와 비교하였다. 압력비의 경우 작동 회전수에서 성능시험과 수치해석의 결과의 경향이 일치하는 것을 확인하였다. 성능시험에서 임펠러의 성능은 매우 높게 나타났으나, 1단 및 2단 디퓨져에서 손실이 발생하여 전체적인 압력비 및 효율이 떨어지는 것을 확인하였다. 수치해석을 통해 내부 유동장을 확인한 결과 1단 디퓨져 및 2단 디스월러에서 격렬한 2차 유동으로 인한 유로차폐효과가 주 손실원인임을 확인하였다.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.2
• /
• pp.83-94
• /
• 2003

Preliminary aerodynamic design of a compressor is carried out to meet the design requirements which are pressure ratio of 13, air mass flow rate of 4 ㎏/s and rotational speed of 45,000 rpm. The compressor type is chosen as an axial-centrifugal compressor from the design requirements which is suitable for a medium power class turboprop or turboshaft engine. Its overall isentropic efficiency is estimated to be 0.796 and its surge margin to be 20% exceeding the design requirement. This paper summarizes the aerodynamic design details including the design procedures and the results of the axial -centrifugal compressor.

• The KSFM Journal of Fluid Machinery
• /
• v.5 no.3 s.16
• /
• pp.46-53
• /
• 2002

This paper reports an experimental investigation on a centrifugal compressor with the adjustable inlet guide vane. The compression system is composed of a radial impeller, a vaneless diffuser, and an IGV. The results have shown that surge line on the performance map is affected by the amount of prewhirl and the prewhirl has an effect on transient region between rotating stall and surge. The surge lines have been shifted toward the lower flow region with the increased positive prewhirl and the higher flow region with the increased negative prewhirl. During the unsteady performance test, it was also found that the transient region was reduced with the increased negative prewhirl, and weak signals of rotating stall were detected just before surge as the positive prewhirl was increased.

• The KSFM Journal of Fluid Machinery
• /
• v.7 no.3 s.24
• /
• pp.23-31
• /
• 2004

An experimental study on the performance and instability development characteristics of a centrifugal compressor equipped with an adjustable inlet guide vane has been performed with varying guide vane angles. The test was conducted at the design speed of 20,800 rpm for 6 guide vane angles : $-30^{\circ},\;-20^{\circ},\;10^{\circ},\;0^{\circ},\;10^{\circ},\;20^{\circ},\;30^{\circ}$. Unsteady pressures were measured using high-frequency pressure transducers at the inducer to investigate the instability phenomena such as rotating stall and surge inside the compressor. From the unsteady measurements, it is found that the transient process from rotating stall to surge was mainly affected by inlet guide vane angles. The results of the present study can be applied to the instability control of the centrifugal compressors using a adjustable inlet guide vane.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.2
• /
• pp.11-16
• /
• 2011

This paper presents a numerical study of casing treatments on a centrifugal compressor stage to improve stability and the surge margin. High efficiency, a high pressure ratio, and a wide operating range are required for a high performance centrifugal compressor. In the present study, a ring groove arrangement was applied to the transonic centrifugal compressor. According to the numerical analysis using a commercial code ANSYS-CFX, the unstable phenomena limiting the range of the centrifugal compressors were compared with and without a ring groove. Although the ring groove decreased the efficiency, but increased the operating range by suppressing a flow separation at the leading-edge of the impeller especially near shroud part. Newly designed ring groove arrangement improved the compressor performance and increased the operating range of the compressor.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.11a
• /
• pp.23-23
• /
• 1997

다목적으로 활용할 수 있는 분리축 방식의 터보축 엔진 개발을 위한 정상상태 해석 프로그램의 개발과 함께 동일 형식의 가스터빈엔진 시험장치를 이용한 실험을 통해 프로그램의 해석결과와 비교, 그 타당성을 입증하였다. 실험에 이용된 시험장치는 1단 원심형 압축기, Can형 연소기, 1단 Radial형 압축기 터빈 및 동력터빈으로 구성되어 있으며 출력은 3상 교류발전기를 통해 획득된다. 해석에 사용된 주요 구성품의 성능곡선은 시험장치 제작자로부터 획득된 자료를 이용하였으며, 경우에 따라 시험장치를 이용한 실험을 통하여 보정하였다. 시험장치를 이용한 실험결과를 프로그램 해석결과와 비교한 결과, 시험장치의 운용제한에 의해 실제 자동영역이 제한되기는 했으나, 압력비, 출력 등 주요 변수들에서 10% 미만의 오차를 보였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.2
• /
• pp.15-23
• /
• 2008

A numerical method based on the prediction of total pressure loss of major components of the engine has been developed for prediction of the windmilling start performance of micro-turbojet engine. The start performance in on/off design region has been analysed by applying this method to predict windmilling start-able regions of the centrifugal-type engine. The results of this analysis have been validated by comparing with the test data. The effect of each design parameters on windmilling start performance has been analysed for the enlargement of start-able regions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.2
• /
• pp.84-90
• /
• 1997

The turboshaft engine with the free power turbine has been used for various purposes, for instance electric power generator, emergency power source, helicopter powerplant and so on. Steady-state simulation program was developed and experimental tests was carried out for comparing with computer simulation results. The test unit was composed of 1-stage centrifugal compressor, the can type combustor chamber, 1-stage radial type compressor turbine, and radial type free power turbine, and its output power is obtained from 3-phase AC generator. Main component characteristics which was used for the steady state simulation program, were obtained from the manufacturer of the test unit, and modified from experimental results of test unit. In comparison between computer simulation and experimental test results even though the test unit has the operational limit, deviation of component performance characteristics in simulation were within 6％ range of experimental results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.319-322
• /
• 2007

A numerical method for prediction of the Windmilling start performance of micro-turbojet engine has been developed. The method incorporates the available loss correlations and analyses for the estimation of the performance of the major engine components. It has been applied to the micro turbojet engine with the mixed type compressor. The starting performance characteristics on the on/off-design regions have been analysed. Additionally, the sensitivity of each design parameter which has an effect on Windmilling start performance has been analysed.