• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.250-256
• /
• 2004

For many years and primarily for economical reasons, Dissimilar Metal Welds have been used as transition joints in a variety of equipment and applications. But Dissimilar Metal Welds have several fabrication and metallurgical drawbacks that can often lead to in-service failures. In this paper, the laser weldability of STS304 stainless steel and SM45C at dissimilar metal welds using a continuous wave Nd:YAG laser are experimentally investigated. An experimental study was conducted to determine effects of welding parameters, on eliminating or reducing the extent welding zone formation at dissimilar metal welds and to optimize those parameters that have the most influence parameters such as focus length, power, beam speed, shielding gas, and wave length of laser were tested.

• 한국압력기기공학회 논문집
• /
• 제11권1호
• /
• pp.25-32
• /
• 2015

Many crack flaws have been detected at tubing seal weld zone in Steam Generator with Alloy600 material tubes. it is very difficult to discriminate the signal from parent material and that from weld zone because weld zone gives complicated ECT signal due to manufacturing processes. ECT signal analysis in the seal weld zone is very important since the tubes with crack in this area shall be out of service by plugging. The purpose of this paper is to distinguish between Parent material and Weld Zone ECT signal in the seal weld zone through the demonstration test of Steam Generator seal weld mock-up.

• 한국정밀공학회지
• /
• 제24권5호
• /
• pp.35-43
• /
• 2007

Laser welding of metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for metals with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the butt welding, the welding quality of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding quality is 1325W of the laser power, and 1.4m/min of laser welding speed.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 춘계학술발표대회 개요집
• /
• pp.241-244
• /
• 1999

The purpose of this study is to examine the characteristics of stress corrosion cracking(SCC) and acoustic emission(AE) signals for the weld HAZ of HT-60 steel under corrosion control in synthetic seawater. Corrosive environment was controlled by potentiostat, and SCC experiment was conducted using a slow strain rate test method at strain rate of 10$^{-5}$ /sec. In order to verify the miroscopic fracture behaviour of the weldment during SCC phenomena, AE test was done simultaneously. Besides, correlationship between mechanical parameters and AE ones was investigated. In case of the parent, reduction of area(ROA) at -0.5V was samller than any other applied voltage such as -0.8V and -1.1V. In addition, reduction of area for the PWHT specimens at -0.8mV was larger than that of the weldment due to the softening effect according to PWHT. In case of the weldment, a lots of events was produced because of the singularities of the weld HAZ compared with the parent.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2001년도 춘계학술발표대회 개요집
• /
• pp.318-321
• /
• 2001

클래딩은 주요 산업분야에 내마모성, 내부식성의 향상을 위해 사용되고 있다. 그러나 클래딩 공정에서는 모재와 클래딩 재료의 물리적, 화학적 특성의 차이와 여러 가지 공정 변수의 영향으로 제품의 사용에 치명적인 손상을 줄 수 있는 균열, 슬래그 개재물, 기공등의 불연속이 발생하기 쉽다. 본 연구에서는 클래딩 시에 발생되는 불연속을 실시간으로 검출하는데 아주 우수한 검출능력을 갖고 있는 비파괴 검사 방법인 음향방출시험을 적용하고 검출된 신호에 대한 주파수 분석과 2차원 위치표정을 실시하여 균열, 기공 등의 불연속을 검출하였고 이를 주사전자현미경을 통하여 확인하였다. 음향방출법에 의해 클래딩부에서 발생하는 결함에 대한 실시간 평가가 가능함을 입증하였으며, 특히 다층 클래딩이나 넓은 면적의 클래딩시에 불연속을 가장 신속하게 감지할 수 있으므로 이를 생산공정에 활용한다면 클래딩 또는 용접부 품질감시를 위한 효과적인 방법이 될 것이다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.326-328
• /
• 2005

High speed rotational arc sensing is an important method to detect the torch deviation during automatic seam tracking of arc welding. In this paper, a mathematic model of high speed rotational arc sensing is analyzed. The simulation results are consistent with the experimental results. The current waveforms at the beginning of the welding are different from those at middle of the welding because of the formation of the weld bead profile. The signal patterns for seam tracking and end-point detection are proposed. A phase shift between the rotation and the current variation is also discovered in the experiments.

• 한국정밀공학회지
• /
• 제21권8호
• /
• pp.57-64
• /
• 2004

This study deals with the prediction of defect location which can be occurred in structure. The existing methods was very difficult to be applied to predict it, because of complex numerical formula. The triangulation method proposed in this study can predict the source location easily with small amount of data. The arrival time of wave can be directly converted into the distance between sensors. For this purpose, the propagation velocity was measured by Rayleigh wave, and the propagation behavior was analyzed. The welded workpiece is adapted to investigate for the consideration of jointed part in structure, The propagation velocity of signal was measured in welded workpiece and the revised algorithm of source location was proposed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.96-101
• /
• 2004

Conventionally, SMAW process was applied to join pipes of RCL, which caused lot of loss in time and cost due to excessive heat input and defects in joining section. Recently, narrow-gap welding(NGW) process was introduced to overcome the disadvantages of SMAW. However, the application of NGW to nuclear power plant is not yet common because safety of NGW process is not proven. In present paper, the welded coupons are made of carbon steel. They are manufactured under different processes; general welding(GW), post-weld heat treatment(PWHT) after GW, repair welding after GW and PWHT with repair welding after GW in carbon steel. Performed are various mechanical tests investigation of microstructure, hardness test, tensile test at room and high temperature, bending test, impact test and J-R test. It is verified that the mechanical properties of carbon steel are greatly changed after repair welding process due to applied heat flux, and that the effect of PWHT is beneficial.

• 한국공작기계학회논문집
• /
• 제15권2호
• /
• pp.51-58
• /
• 2006

Laser welding of dissimilar metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for SM45C and STS304 with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the dissimilar welding, the welding quality of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding qualify is 1600W of the laser power, 0.85m/min of welding speed and $4{\ell}/min$ of pressure for shielding gas.

• 대한기계학회논문집A
• /
• 제28권2호
• /
• pp.165-173
• /
• 2004

Laser beam welding is increasingly being used in welding of structural steels. The laser welding process is one of the most advanced manufacturing technologies owing to its high speed and deep penetration. The thermal cycles associated with laser welding are generally much faster than those involved in conventional arc welding processes, leading to a rather small weld zone. Experiments are performed for 304 stainless steel plates changing several process parameters such as laser power, welding speed, shielding gas flow rate, presence of surface pollution, with fixed or variable gap and misalignment between the similar and dissimilar plates, etc. The following conclusions can be drawn that laser power and welding speed have a pronounced effect on size and shape of the fusion zone. Increase in welding speed resulted in an increase in weld depth/ aspect ratio and hence a decrease in the fusion zone size. The penetration depth increased with the increase in laser power.