• Journal of Energy Engineering
• /
• v.8 no.1
• /
• pp.23-33
• /
• 1999

용융탄산염 연료전지의 대형화에 관한 기본 기술을 확립하기 위하여 전극의 유효면적이 625 $\textrm{cm}^2$인 단위전지를 20단 적층한 내부 분배형 용융탄산염 연료전지 스택을 제작하고 그 성능을 살펴보았다. 연료로 72% H2/18% CO2/10% H2O를 , 산화제로는 70% air/30% CO2의 혼합 기체를 사용하여 운전한 결과 전류밀도가 150 mA/$\textrm{cm}^2$이고 연료 및 산화제의 이용율이 0.4일 때, 스택 전압이 16.62 V로 1.56 kW의 높은 초기출력을 나타내었다. 스택 내 분리판에서의 온도 분포는 가스 흐름 방향으로 온도가 증가하였으며 스택출력이 높아질수록 가스 배출 부분의 온도가 상승하였다. 스택 내 각 단위전지간의 성능 분포는 균일하지 않았으며, 가스이용율에 따라 그 편차가 증가하였다. 연속 운전 300시간 후부터 스택의 성능이 감소하였으며, 그 원인을 분석한 겨로가 탄소 석출과 부식 생성물에 의한 전기 단락 때문으로 밝혀졌다. 본 연구를 통하여 anode 출구에서의 가스 조성을 분석함으로써 전기 단락에 의한 전압 손실량을 계산하는 기법을 확립하였다. 또한 본 연구에서 얻은 결과를 통하여 향후 스택의 대형화와 장수명화에 대한 대책을 제시하였다.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.3
• /
• pp.203-210
• /
• 2010

NiO is commonly used as the cathode for the molten carbonate fuel cell due to its stability and high electrical conductivity in molten carbonates and oxygen atmosphere. However, long-term operation of MCFC has a serious problem which is the degradation of cathode material, the so-called Ni dissolution. In the present study, we have attempted to synthesize a new alternative cathode material as Co/Nb-coated NiO cathode. The results obtained in this study suggest that the Co/Nb-coated NiO cathode can be utilized as having lower dissolution and higher cell performance than those of the pure NiO cathode.

• Korean Journal of Materials Research
• /
• v.8 no.8
• /
• pp.685-692
• /
• 1998

Since a wet-seal area of Molten Carbonate Fuel Cell (MCFC) operated at $650^{\circ}C$ is exposed to severe environment, a life-time of MCFC is influenced by the corrosion resistance of separator. In order to improve corrosion resistance of 316L stainless steel used as separator material, AI- base alloy such as NiAI has been widely used as coat¬ing material on the wet-seal area. The purpose of this work is to develope a more protective coating material by adding yttrium on NiAI alloy. An immersion test and a polarization test were performed in molten carbonate salt at $650^{\circ}C$ to estimate corrosion resistance of the NiAI alloy and the NiAl/Y alloys with up to L5at% yttrium. NiAl/Y alloys showed better corrosion resistance than NiAI alloy. We found that more than 0.7 at% yttrium was required to improve the corrosion resistance of NiAI alloy in molten carbonate salt at $650^{\circ}C$.

• The Journal of the Petrological Society of Korea
• /
• v.10 no.1
• /
• pp.1-12
• /
• 2001

A small of carbonate rocks and spatially-associated ultramafic rocks uniquely occur in the ulsan iron-serpentine mine of the sourtheastern Kyungsang basin. The study of field geology, core drilling data and stable isotope analysis suggest that the carbonate rocks are carbonatite formed from the melt reflecting intrusive natures. Based on this study, the geology of the Ulsan iron-serpentinite mining area consists of Cretaceous sedimentary, volcanic, granitic ultramafic and carbonate rocks in ascending order. The carbonate and ultramafic rocks show concentric and ellipsoidal shapes at the outcrop and a funnel shape in the cross sectional view. Carbon and oxygen stable isotope analysis show a bimodal pattern rather than a typical mantle pattern, which may indicate that the melt was a secondary melt generated within the crus not in the mantle directly. The uprising of ultramafic melts would have melted lime-contained rocks forming a secondary carbonate melt in the upper crus. Then, the intrusion of the ultramafic melts would have melted lime-contained rocks forming a secondary carbonate melt in the upper crust. Then, the intrusion of the ultramafic melt was followed by the intrusion of the carbonate melt along deep-seated fractures. Well-developed major fractures in this area, fluid inclusion characteristics of the carbonate rocks, the spatial relation between the ultramafic and carbonate rocks and stable isotope data support interpreting the Ulsan carbonate rocks as carbonatite.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.3
• /
• pp.136-140
• /
• 2000

A stainless steel separator for a molten carbonate fuel cell is usually coated with aluminum diffusive layer to protect its surface against corrosion by the molten carbonate at high temperatures. In this study, a relatively simple method was devised to form the aluminum diffusive layer on a stainless steel substrate. Slurry coating of aluminum on the substrate followed by heat treatment under reducing atmosphere at $650\~800^{\circ}C$ produced the aluminum diffusive layer of $25\~80{\mu}m$ thickness. The thickness of aluminum diffusive layer increased with increasing the temperature or duration of the heat-treatment. The corrosion resistance against molten carbonate under oxidizing atmosphere was significantly improved by aluminum diffusive layer formed by the sluny painting and heat treatment method. Moreover, the sample prepared in this study showed corrosion behavior similar to the sample with aluminum diffusive layer prepared by ion vapor deposition and heat treatment.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.146-151
• /
• 2001

Several design parameters for a 100 kW molten carbonate fuel cell stack was described. Approximately 170 cells are required to generate 100 kW at a current density of $125\;mA/cm^{2}$ with $6000\;cm^{2}$ cells. An overall heat balance was calculated to predict exit temperature. In order to limit the stack temperature in the range of $600-700^{\circ}C$, current load cannot exceed $75\;mA/cm^{2}$ at atmospheric operation. The 100 kW power is expected only under pressurization. Recycle of cathode gas by more than 50% is recommended to run the stack at $125\;mA/cm^{2}$ and 3 atm. Manifolds should be designed based on gas flow rates for the suggested operating condition.

• Journal of Hydrogen and New Energy
• /
• v.26 no.2
• /
• pp.156-163
• /
• 2015

The fuel cells have been investigated in the applications of marine as the high efficient and eco-friendly power generating systems. In this study, modeling of IR Type molten carbonate fuel cell (Internal Reforming Type molten carbonate fuel cell) has been developed to analyze the feasibility of thermal energy utilization. The model is developed under Aspen plus and used for the study of system performances over regarding fuel types. The simulation results show that the efficiency of MCFC system based on NG fuel is the highest. Also, it is also verified that the steam reforming is suitable as pre-reforming for diesel fuel.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1999.05a
• /
• pp.225-228
• /
• 1999

MCFC의 장수명화를 위해 기존의 Li$_2$CO$_3$-K$_2$CO$_3$계 전해질을 Li$_2$CO$_3$-$Na_2$CO$_3$계 용융탄산염으로 대체함으로써, 전지 수명을 단축시키는 NiO의 용출을 억제하고자하는 연구가 진행중에 있다. 이러한 대체 Li$_2$CO$_3$-$Na_2$CO$_3$ 전해질은 실제 전지에서 사용되고 있는 분리판 재료인 스테인레스강의 안정성에도 기존의 Li$_2$CO$_3$-K$_2$CO$_3$ 혼합염과는 다른 경향을 보이는 것으로 알려져 있다.(중략)

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1999.05a
• /
• pp.219-223
• /
• 1999

1993년부터 시작한 선도기술개발 사업의 1단계 사업은 용융탄산염형 연료전지(Molten Carbonate Fuel Cell ; MCFC) 기초 기술기반을 확립하기 위하여 단위전지 요소기술 제작, 소규모 스택의 운전 및 운용 등을 중심으로 연구개발이 진행되어 1996년에는 2 kW급 MCFC 시스템을 개발 3,250 시간 장기 운전평가를 실시 하므로써 소기의 목적을 달성하였다.(중략)

• Clean Technology
• /
• v.26 no.4
• /
• pp.329-335
• /
• 2020

Methanol synthesized from renewable hydrogen and captured CO2 has recently attracted great interest as a sustainable energy carrier for large-scale renewable energy storage. In this study, molten carbonate fuel cell's performance was investigated with the direct conversion of methanol into syngas inside the anode chamber of the cell. The internal reforming of methanol may significantly improve system efficiency since the heat generated from the electrochemical reaction can be used directly for the endothermic reforming reaction. The porous Ni-10 wt%Cr anode was sufficient for the methanol steam reforming reaction under the fuel cell operating condition. The direct supply of methanol into the anode chamber resulted in somewhat lower cell performance, especially at high current density. Recycling of the product gas into the anode gas inlet significantly improved the cell performance. The analysis based on material balance revealed that, with increasing current density and gas recycling ratio, the methanol steam reforming reaction rate likewise increased. A methanol conversion more significant than 90% was achieved with gas recycling. The results showed the feasibility of electricity and syngas co-production using the molten carbonate fuel cell. Further research is needed to optimize the fuel cell operating conditions for simultaneous production of electricity and syngas, considering both material and energy balances in the fuel cell.