• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.8
• /
• pp.403-409
• /
• 2018

Inconel 713C which of a commercial Ni super alloy have the composition of 70 % Ni, 12 % Cr, 6 % Al and 4 % Mo. Mo is very expensive and have some economic value to recover in the alloy. In this study, liquid-liquid exraction(solvent extraction and stripping) has been performed to separate Mo from the synthetic leaching solution of spent Inconel 713C alloy and prepare to Mo powder by dying, evaporation and heat treatment. The experiments were conducted by using synthetic leaching solution which was prepared $NaMoO_4$ $2H_2O$ by dissolved in distilled water. Alamine336 and Cyanex272 dissolved in kerosene were used as extractants. The extraction percentage of Mo by Alamine336 is 99 % in the condition of the range of pH 1 to 4 and 1 % of concentration of Alamine336. The stripping solutions are used by HCl, $H_2SO_4$ and $HNO_3$ solutions and the concentrations were controlled by distilled water. The concentrations of HCl, $H_2SO_4$ and $HNO_3$ as stripping solutions are increased, the stripping percentages of Mo are increased and the stripping percentage of Mo by $HNO_3$ is higher than other stripping solutions. After liquid-liquid extraction and heat treatment, $MoO_3$ powder which of the purity of 97.5 % was prepared.

• KSBB Journal
• /
• v.22 no.5
• /
• pp.328-335
• /
• 2007

In this work ursolic acid (UA), a poorly water-soluble compound, was inclusion complexed with 2-hydroxypropyl-$\beta$-cyclodextrin (HP-$\beta$-CD) by various methods such as kneading, solvent evaporation and two types of supercritical fluid processes. The solubility and characteristics of these UA/HP-$\beta$-CD complexes were investigated by scanning electron microscopy, x-ray diffraction and HPLC. The water solubilities of the two complexes obtained from solvent evaporation and ASES processes were observed to increase up to 6$\sim$240 folds and 12$\sim$56 folds, respectively, compared with that of unprocessed UA. The stability of UA/HP-$\beta$-CD complex samples in cosmetic formulations was examined at various temperatures for one month. The UA/HP-$\beta$-CD complex prepared by solvent evaporation was found to be most stable among all the cosmetic formulations tested in our experiments.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2006.05a
• /
• pp.90-94
• /
• 2006

The waste solution discharged from the LCD manufacturing process contains acids like nitric, acetic and phosphoric acid and metal ions such as Al, Mo and other impurities. It is important to removal of impurities to tess than 1ppm in phosphoric acid to reuse as an etchant because the residual impurities even in sub-ppm concentration in semiconductor materials play a major role on the electronic properties. In this study, we have been clearly established that a mixed system of solvent extraction, diffusion dialysis and ion-exchange technique, which made individually the most of characteristics is developed to commercialize in an efficient system for recovering the high-purity phosphoric acid. By applying vacuum evaporation, the yield of the process are almost 99% removal of nitric acid and acetic acid was achieved. And by applying the solvent extraction method with tri-octyl phosphate(TOP) as an extractant, the removal of acetic and nitric acid from the acid mixture was achieved effectively at the ratio O/A=1/3 with four stages and the stripping of nitric acid from organic phase is attained at a ration of O/A=1 with six stages by distilled water. About 97% and 76% removal of Al and Mo were achieved by diffusion dialysis. Essentially complete less than 1ppm removal of Al, Mo by using ion exchange ion resin and purification of the phosphoric acid was obtain.

• Polymer(Korea)
• /
• v.37 no.6
• /
• pp.702-710
• /
• 2013

Zaltoprofen loaded polyoxalate (POX) microspheres were prepared by an emulsion solvent-evaporation/extraction method like oil-in-water (O/W) for sustained release of zaltoprofen. The influence of several preparation parameters such as fabrication temperature, stirring speed, intensity of the sonication, initial drug ratio, molecular weight ($M_w$) of POX, concentration of POX and concentration of emulsifier has been investigated on the zaltoprofen release profiles. Physicochemical properties and morphology of zaltoprofen loaded POX microspheres were investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), differential scanning calorimeter (DSC) and Fourier transform infrared (FTIR). Through the analyzed results, it was demonstrated that the characteristics of the microspheres greatly affected by the prepared condition. The releases behavior of zaltoprofen was investigated for 10 days in vitro. It was confirmed that the release behavior of zaltoprofen can be controlled by the manufacturing factor of solvent-evaporation/extraction method.

• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.473-477
• /
• 2022

In this study, candidate technologies for lithium recovery from the process waste liquid generated in the waste battery recycling process were reviewed, and technologies applicable to the process from the commercialization point of view were reviewed from a qualitative point of view. The evaporation method is difficult to apply because it requires a large-scale land and shows a low recovery rate due to the loss of Li during the concentration process. In the case of precipitation, a commercially available technology shows a high recovery rate due to the high Li/Na selectivity of phosphoric acid, but there are disadvantages in that the process is complicated due to the use of expensive phosphoric acid, requiring a recovery step, and continuous operation is impossible because solids are handled in the Li concentration process. In the case of solvent extraction, if we find an inexpensive extractant with high Li/Na selectivity, continuous operation is possible with the method used in extraction of other metals in the previous step, and when Li is concentrated, continuous operation is possible because it is in a liquid state. If it shows a similar recovery rate compared to precipitation technology, commercialization will be the most likely.

• Membrane Journal
• /
• v.17 no.3
• /
• pp.184-190
• /
• 2007

This study reports on the pervaporation separation of a volatile organic compound(VOC), dichloromethane(DCM) from water using fluorinated copolysiloxaneimide membranes. The copolysiloxaneimide membranes were prepared from 4,4'-(hexafluoroisopropylidene)diphthalic anhydride(6FDA) and two diamines(polysiloxane diamine(SIDA), 2-(perfluorohexyl)ethyl-3,5-diaminobenzene(PFDAB)). By varying the ratio of flexible polysiloxane diamine(SIDA)/rigid fluorinated aromatic diamine(PFDAB) from 0/100 to 100/0 mol%, five copolysiloxaneimide membranes were prepared success- fully. The pervaporation properties of DCM/water were examined in terms of two diamine monomer ratio at room temperature and the feed composition of 0.05 wt% in water. It was found that the increase in SIDA content led to high permeation flux and pervaporation selectivity towards DCM by the enhanced sorption/sorption selectivity and diffusion coefficient/diffusion selectivity due to the increased hydrophobicity and fractional free volume.

• Korean Chemical Engineering Research
• /
• v.44 no.3
• /
• pp.277-283
• /
• 2006

Aqueous solution of sodium glycinate was checked as a suitable $CO_2$ absorbent from the flu gas in the thermal power plant. For this purpose, solubility, vapor pressure, latent heat of vaporization and thermal conductivity were determined for pure and aqueous solution of sodium glycinate. The solubility of sodium glycinate in the solvent, 25 g of $H_2O$, was increased with increasing the temperature and their relation was represented as a first order equation of y = 0.3471x + 20.993. The vapor pressure for 10 wt％ to 60 wt％ of aqueous sodium glycinate solution were determined and the latent heat of vaporization of each aqueous solution was calculated from measured vapor pressure using Clausius-Clapeyron equation. Besides, thermal conductivity of sodium glycinate powder was also determined and it was $1.0933kcal/m{\cdot}hr{\cdot}^{\circ}C$.

• Membrane Journal
• /
• v.10 no.3
• /
• pp.130-138
• /
• 2000

Polyethersulfone (PES) asymmetric membranes for gas separation were prepared by dry/wet phase inversion method and their separation properties for CO$_2$ and N$_2$ gases were investigated. The effects of important variables such as composition of casting solution and evaporation time in preparation of asymmetric gas membrane on membrane morphology and the separation properties were analyzed and the optimum condition of membrane preparation was established. To compensate the defects like pinholes existed on skin layer of the membrane prepared, the membranes were coated with silicone resin. By comparing separation properties after coating with those before coating, we found that the coating of silicone resin was effective to enhance the separation properties. The casting solution mainly used in this study consisted of PES, N-methyl-2-pyrrolidone, acetone, ethanol and distilled water was used as coagulation agent. It was shown that the selectivity for CO$_2$/N$_2$ was getting higher but the permeability decreases, as the contents of PES and volatile organic solvent and evaporation time increased. The selectivity for CO$_2$/N$_2$ and permeability of CO$_2$ of the membrane prepared under the optimum condition were found to be 61 and 21 GPU, respectively.

• Elastomers and Composites
• /
• v.34 no.1
• /
• pp.45-52
• /
• 1999

This paper describes how the gold particles self assemble on the specific phase on the microphase separated block copolymer thin film and form a well ordered patterns. For this study, polystyrene-polybutadiene-polystyrene (PS-PB-PS) triblock copolymer (30wt % PS) thin films (${\sim}100nm$) having a cylindrical morphology were cast from 0.1wt% toluene solution to be used as polymer thin film templates. The films having either vertical PS cylinders or in-plane PS cylinders in PB matrix from each different solvent evaporation condition were obtained. Cross-sectional transmission electron microscopy(TEM) was used to study the surface and bulk morphologies of block copolymer thin films. Small amount of gold particles was evaporated on a block copolymer thin film template to obtain a nano-scale pattern. When an as-cast thin film template was used, gold particles preferentially self assemble on the low surface tension PB phase and a relatively well ordered pattern in nano-scale was produced. However, after the formation of a low surface energy PB rich layer upon annealing, a gold self-assembled pattern was not observed.

• Membrane Journal
• /
• v.29 no.1
• /
• pp.61-65
• /
• 2019

Anisotropic particles have been issued in various fields due to their unique physical properties. Herein, a novel dynamic phase separation method (DPS) is introduced to fabricate anisotropic acorn-like nanoparticles. DPS consists of two dynamic conditions; solvent evaporation and nonsolvent induced precipitation. The bottom layer is controlled by feeding the water as a non-solvent diluent, and the phase separation of the upper layer relies on the diffusion and evaporation of a volatile good solvent. At this condition, the acorn-like particles were fabricated. Under a closed box filled with water (spontaneous phase separation), monodisperse polystyrene (PS) particles were synthesized. At the coexistence between DPS and spontaneous phase separation, the sizes of cap and particle were changed. Also, the volume of PS solutions influences on the particle shape. Since the unique structures could be utilized into various applications, if advanced techniques such as membrane-based controlled water feeding is developed, monodisperse acorn-like particles could be tuned.