• Journal of Bio-Environment Control
• /
• v.10 no.2
• /
• pp.80-87
• /
• 2001

This study was conducted to provide basic data for the design of shading facility of greenhouse. The proper distance between external shading screen and roof surface, transmissivity of shading materials, and shading effects of external and internal shadings were analyzed. About a distance of 10 cm between inclined external shading screen and roof surface was enough to guarantee the external shading effect in the greenhouse without roof vent. The inside temperature of greenhouse installed with 85% internal shading screen was lower the maximum of 4$^{\circ}C$ and mean of 2$^{\circ}C$ than that with 55% internal shading screen in both natural ventilation and no ventilation condition. The difference of soil temperature between shading and no shading greenhouse was great, but the difference by shading rate or shading method was small. The performance of external shading for controlling inside temperature down was superior to that of the internal shading. The externally inclined shading screen parallel to the roof surface of greenhouse was more effective than the externally horizontal shading screen in controlling inside temperature of greenhouse without roof vent.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.229-232
• /
• 2008

In rapid cycle construction, RC structure which is not cured fully can be loaded with construction load and this construction load can influence on the safety of construction and cracks on slabs. Therefore, to reduce the term of construction, the safety of construction and prevention of cracks should be assured against construction load. In the previous study, temperature load can significantly influence on the behavior of structure under construction. However, existing construction sequential analysis or design code do not consider temperature load reasonably. In the present study, through construction sequential analysis method using FE analysis, the behavior of structure under construction was analyzed according to temperature changes. According to the results of analysis, as the temperature falls, shoring load drops and the temperature rises, shoring load rises. These variations of shoring load can affect the safety of construction. Moment of slab goes up by fall in temperature. This increase of moment can cause cracks on the slab. Therefore to assure the safety on construction and prevent cracks on slabs, temperature load has to be considered reasonably in construction sequential analysis.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 2000.10b
• /
• pp.128-131
• /
• 2000

자갈축열 태양열 온실에 있어 여름철 냉방에너지의 효과적인 절감 방안을 모색하고자 축열 및 배기시스템의 작동방식을 다르게 하여 주ㆍ야간 축열과 방열시 자갈축열층의 온습도환경을 분석한 결과를 요약하면 다음과 같다. 1. 주간에 외기온이 28.5$^{\circ}C$-35.3$^{\circ}C$범위에서 변화할 때 자갈축열층내로 유입되는 공기의 온도는 30.5$^{\circ}C$-36.2$^{\circ}C$, 자갈축열층에서 온실내부로 유출되는 공기의 온도는 28.2$^{\circ}C$-30.1$^{\circ}C$, 축열층 내부온도는 27.4$^{\circ}C$-35.9$^{\circ}C$ 범위였다. 또한, 10시간 축열시 자갈축열층 내부온도는 측점에 따라 1.7$^{\circ}C$-7.$0^{\circ}C$의 온도상승이 있었으며 유입구에서 멀어질수록 축열층 온도는 낮게 나타났으며 온도상승 속도 또한 감소하는 경향으로 나타났다. 그리고, 야간에 축열시스템을 작동하지 않고 배기팬만을 작동하였을 경우, 외기온이 27.4$^{\circ}C$-34.4$^{\circ}C$범위일 때 자갈축열층 내부온도는 29.7$^{\circ}C$-34.9$^{\circ}C$(평균 31.4$^{\circ}C$)범위였으며 온실외부에 설치되어 있는 배기구와 배기팬의 영향으로 축열층 내부온도는 시간이 경과함에 따라 감소하는 경향으로 나타났으며 측점에 따라 2.2$^{\circ}C$-5.1$^{\circ}C$(평균 2.8$^{\circ}C$)의 온도하강 효과가 있는 것으로 나타났다. 2. 여름철 주간에 10시간 축열시 자갈축열층 내부습도는 측점에 따라 8.1%-26.3%의 감소현상이 있었다. 또한, 유입구에서 멀어질수록 축열층 습도는 높게 나타났으며 습도하강속도 또한 감소하는 경향으로 나타나 유입구에서 멀어질수록 외부습도의 영향을 적게 받는 것으로 분석되었다. 하지만, 야간에는 배기시스템의 영향으로 자갈축열층의 습도는 외기의 영향을 많이 받는 것으로 나타났다.

• Journal of Internet of Things and Convergence
• /
• v.10 no.2
• /
• pp.125-130
• /
• 2024

With the rapid growth of mobility technology, the industrial sector is demanding storage devices that can reliably process data from various equipment and sensors in vehicles. NAND flash memory is being utilized as a storage device in mobility environments because it has the advantages of low power and fast data processing speed as well as strong external shock resistance. However, flash memory is characterized by data corruption due to long-term exposure to high temperatures. Therefore, a dedicated system for temperature management is required in mobility environments where high temperature exposure due to weather or external heat sources such as solar radiation is frequent. This paper designs a dedicated temperature management system for managing storage device temperature in a mobility environment. The designed temperature management system is a hybrid of traditional air cooling and water cooling technologies. The cooling method is designed to operate adaptively according to the temperature of the storage device, and it is designed not to operate when the temperature step is low to improve energy efficiency. Finally, experiments were conducted to analyze the temperature difference between each cooling method and different heat dissipation materials, proving that the temperature management policy is effective in maintaining performance.

• KSBB Journal
• /
• v.15 no.6
• /
• pp.548-555
• /
• 2000

A hydrogel, poly(N-isopropylacrylamide-co-N, N-dimethylaminopropylmethacrylamide), sensitive to both pH and temperature, was synthesized and characterized at $^13∼23{\circ}C$ and pH of 10.3∼12.3. The gel was more transparent and mechanically stronger at lower preparation temperature and pH. Large pores observed in scanning electron microscope seem to be responsible for the lower biomolecular separation efficiency. The lower critical solution temperature (LCST) decreased at a higher polymerization temperature. At $25^{\circ}C$, which is lower than the LCST, the gel was swollen regardless of the solution pH. At $40^{\circ}C$, however, the gel was swollen at neutral and acidic pHs even though the temperature was higher than the LCST. The gel collapse pH, defined as the point at which the gel made its largest volume decrease per unit pH increment, increased as the gel preparation temperature increased.

• Journal of Bio-Environment Control
• /
• v.30 no.3
• /
• pp.230-236
• /
• 2021

Changes in greenhouse temperature and solar radiation due to fogging and shading were monitored during hydroponics in high temperature in summer season. Experiment 1 consists of four treatments, namely, Control, Shading, Fogging, and Fogging + Shading based on sunny days August. For Experiment 2, two melon cultivars of 'Dalgona' and 'Sopoong gaza' were cultivated in summer of 2020 using Fogging + Shading with the best result for temperature reduction effect from Experiment 1. As a result of Experiment 1, the effect of Fogging + Shading on temperature reduction was apparent where the inside was about 4℃ (as the lowest temperature) lower than the outside. Fogging + Shading showed the inside was 2-4℃ lower than the outside, and Fogging or Shading treatments had little difference, compared to the Control where the internal temperature of greenhouse was 3-4℃ higher than the external. For solar radiation changes between greenhouse inside and outside, the internal change was in a similar pattern between Fogging and Control, and between Shading and Fogging + Shading, respectively. In case of the Fogging treatment (similar with the Control) only the effect of solar radiation reduction as influenced by plastic greenhouse covering materials was examined. The Fogging + Shading had a very similar change in solar radiation to the Shading. Based on these results, Experiment 2 was conducted in summer of 2020 and resulted in a temperature reduction effect of about 3.9℃ according as the inside of air-conditioned greenhouse was kept 32.4℃ when the maximum temperature of the outside reached 36.3℃ in August during the cultivation period. In addition, the quality of melon fruit was good (1.3-1.5 kg of fruit weight, 12.6-13.3 of soluble solids content. In the case of using Fogging + Shading cooling treatment, it can bring about the effect of reducing the temperature during the high temperature in summer, and normal growth of melon and fruit harvesting were possible.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2004.10a
• /
• pp.172-177
• /
• 2004

• Journal of Korean Society of Steel Construction
• /
• v.21 no.5
• /
• pp.443-450
• /
• 2009

This paper describes the experimental study that was conducted on the temperature characteristic and bending capacity of a steel-plate-reinforced concrete-wall module (SC module). The steel plate ratio and temperature loading parameters were tested, and the influence of these parameters on the moment-curvature relationship and on the bending strength of the SC module was investigated. The fundamental-structure characteristic result of every SC module that assumed practical use was investigated. In this study, the bending and flexural characteristics of SC structures were evaluated to verify the yielding and ultimate strength of the SC beam under thermal-loading conditions.

• Ceramist
• /
• v.8 no.1
• /
• pp.50-56
• /
• 2005

압전재료의 다양한 에너지 변환특성 중 기계-전기 에너지간 변환 특성만을 이용하고자 하는 경우로 한정하고, 압전재료의 물성 및 진동모드, 재료물성 평가 사례들을 요약하여 소개하였다. 그러나 이상에서 설명한 압전특성은 매우 개략적인 개념으로서 우수한 압전 응용부품을 개발하기 위해서는 몇 가지 유의할 사항들이 있다. 압전재료는 보다 기본적으로 열에너지, 기계에너지, 전기에너지, 나아가서 Maxwell 방정식에 의해서 전기장과 연결되는 자기에너지까지도 연결시켜서 상호간에 에너지 변환작용을 일으킬 수 있는 특성을 가진다. 기계적 변형(S) = 탄성변형효과 + 역압전효과 + 열팽창효과 전기적 변위(D) = 압전효과 + 유전효과 + 초전효과 즉, 압전 응용부품이 온도변화 및 자기장이 인가되는 환경에서 순수하게 압전현상만을 이용하고자 한다면, 응용분야 및 주위환경에 따라 압전세라믹 소자가 외부 환경변화에 반응을 하지 않도록 적절한 차단 대책을 수립하여야만 한다. 그러나 압전재료의 외부 자기장의 변화에 대한 반응도는 전기장에 대한 반응도에 비해서 매우 작으므로 통상 무시해도 무방하다고 본다. 그리고 압전재료에서 전기장-기계장의 선형성이 보장되는 크기에는 뚜렷한 한계가 있고, 선형성 영역을 벗어나면 이력특성에 의해 비선형 특성 및 포화상태를 보이게 된다는 점 또한 주의하여야 할 점이다. 또한 압전특성은 Curie 온도이하에서만 존재하고, 그 이상의 온도에서는 쌍극자들의 지나친 운동성에 의해 결정 대칭성이 변하여 압전특성이 소멸되므로 사용 온도 구간에 엄격한 제한을 두어야 함도 응용에 유의하여야 한다.

• Electrical & Electronic Materials
• /
• v.3 no.3
• /
• pp.187-194
• /
• 1990

광자기 메모리용 재료인 비정질 TbFe 박막을 대상으로 열자기 기록시 박막에 분포하는 온도와 이때 만들어지는 bit의 크기간에 상호관련성을 조사하였다. 레이저 조사에 의해 가열된 박막의 온도분포는 유한요소법을 이용한 열전달 해석에 의해 계산하였다. 레이저 가열종료 직전 박막 면에 분포하는 온도 contour로 부터 bit 크기를 예측하였다. 여기서 bit 크기는 온도 상승에 따라 보자력이 약화되어 외부자계와 박막반자장의 합력이 역자구를 만들어 준다고 가정하여 이 경계가 되는 온도(Tcrit)로 이루어지는 등온선의 크기로부터 정하였다. 열자기 기록 실험으로부터 기록 bit의 크기(Dmeas.)을 측정하여 레이저조사조건별로 예측한 bit크기(Dpred.)와 비교하였다. 특히, 레이저 pulse시간 변화에 따른 여러온도의 등온선 contour 직경변화를 조사하여 실측한 bit크기와 비교 검토함으로써 bit형성에 미치는 온도분포의 영향을 조사하였다. 이 결과 레이저 pulse시간이 길어지거나 레이저 power가 상대적으로 작을때 실측한 bit크기가 예측된 bit크기보다 커지는 것으로 나타났으며 이는 Tcrit 온도구배가 완만해질수록 bit경계가 되는 온도가 낮아지는 것으로 해석된다.