• Journal of Korean Society of Steel Construction
• /
• v.26 no.4
• /
• pp.323-334
• /
• 2014

In this paper, experimental program and associated numerical study were carried out to evaluate the fire resistance of unprotected concrete-filled rectangular steel tubular (CFT) columns subjected to the standard fire. The key testing parameters included the length effect, the load ratio, and the sectional dimensions of the CFT columns. Temperature distribution and axial deformation of the CFT column specimens were measured and analyzed. Rather early local buckling of steel tubes was observed in all the specimens. This caused subsequent load transfer from steel tube to concrete, and eventually triggered concrete crushing, or complete loss of the load bearing capacity of the column. This implies that the limit state of local buckling as well as overall flexural buckling should be incorporated in fire design procedure. As expected, the fire resistance time of specimen with higher load ratio consistently lessened. The prediction of fire resistance time of unprotected CFT columns based on the limiting steel temperature in current design codes or the formula proposed by previous studies is slightly conservative compared to the fire test results available. To establish the finite element analysis model that can be used to predict the thermal and structural behaviour of unprotected CFT columns in fire, the fully coupled thermal-stress analysis was also tried by using the commercial code ABAQUS. The numerical results showed a reasonable global correlation with the experimental results.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.232-233
• /
• 2004

강구조물 제작 시 용접프로세스에 의해 용접부 근방에 불균일한 온도분포가 발생하여 용접변형이 발생된다. 이러한 용접변형은 좌굴강도와 피로강도를 저하시킬 뿐 아니라 구조물의 크기와 형상을 변화시켜 이를 교정하거나 수정하기 위해 추가작업을 실시해야함으로 생산성을 저하시키는 주요한 요인이 되고 있다. (중략)

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.7 s.94
• /
• pp.1686-1699
• /
• 1993

In this paper, the thermal buckling of thick composite angle-ply laminates subject to uniform temperature distribution is studied. For the plates of 4-edges simply supported condition and those of 4-edges clamped condition, the critical buckling temperatue is derived, using tile finite element method based on the shear deformation theory. The effects of lamination angle, layer number, laminate thickness, plate aspect ratio and boundary constraints upon the critical buckling temperature are presented.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.7 s.250
• /
• pp.809-815
• /
• 2006

The temperature and loading-rate dependence on the mechanical behavior of single-walled carbon nanotubes under axial compression and torsion is examined with classical molecular dynamics simulation. The critical buckling is found to depend on the temperature and loading-rate. The yielding under torsion is also found to depend on the temperature and loading-rate. But it is shown that the compression and torsional stiffness are independent of the varied temperatures and loading-rates.

• Proceedings of the KSR Conference
• /
• 2002.05a
• /
• pp.207-212
• /
• 2002

The actual buckling of the railroad track structure is suspected to be a complex interaction between the vertical, lateral and torsional modes. To make the analysis tractable, however, most studies restrict themselves to either the vertical or the horizontal plane. Based on a comprehensive and realistic three-dimensional track model developed in the previous study, three dimensional buckling analysis of CWR track subjected to temperature load was performed. Using the study on buckling temperature and mode, sensitivity of track components such as tie spacing, ballast resistance, stiffness of pad-fastening system and rail size were investigated.

• Proceedings of the KSR Conference
• /
• 2002.10a
• /
• pp.654-659
• /
• 2002

Continuous Welded rail(C.W.R.) tracks has many advantages over the conventional jointed rail track. Due to the elimination of rail joints for thermal expantion, however it many cause the track to be suddenly bucklled by thermal loads. The present study investigates the influences of Pad-fastner on the Thermal buckling behavior of C.W.R. Parametric studies are performed to evaluate the effects of the individual parameters on the upper and lower critical bucklig temperature.

• Journal of the Korean Society for Railway
• /
• v.13 no.2
• /
• pp.179-185
• /
• 2010

In order to secure safety for the buckling and fracture of continuous welded rail and improve the efficiency of maintenance work, it is very important that grasp the characteristics of rail temperature. Recently, the maximum air temperature in summer season rises gradually and the minimum air temperature in winter season is decreasing gradually due to the climate change. Therefore, these phenomenon influences in the change amount of yearly rail temperature and can cause change of laying and maintenance temperature. In this study, actual measurement of rail temperature including climatic factors is carried out by constructing the temperature and climate measurement system as realistic as possible. Through the intensive investigation of actual data, it is founded that the existing prediction formulas for rail temperature may be used only in certain climatic conditions (certain combination of climatic factors). It may be more reasonable that the rail temperature considering actual climatic factors in site is predicted on probabilistic approach.

• Journal of the Korean Society for Railway
• /
• v.3 no.1
• /
• pp.19-26
• /
• 2000

The rail temperature is important to preserve the joint gap for standard length of rail and to determine the installation temperature which has direct influence on the rail buckling and failure in welded part for continuous welded rail(CWR), Therefore, we have measured and investigated various characteristics of rail temperature for each kind of rail. As the results of this, the correlation between the atmosphere temperature and the rail temperature which is commonly used by Korean Railway should be reconsidered. Also, the daily highest '||'&'||' lowest rail temperature was occurred when each temperature is higher and when it's lower. For the light rail, the rail temperature by the sun-light increases quickly and decreases late. But the time where the highest temperature is attained is same. There are some differences between the shade and sunny place about 3.0∼4.0$\^{C}$. The temperature of rail web is almost close to the conversion rail temperature for rail expansion. The wind of 1 m/s has an influence on the rail temperature around 5$\^{C}$.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.952-958
• /
• 1988

To analyze the nonflatness and residual stress in accelerated cooled plate, a numerical analysis model has been developed. Two factors, i.e. temperature and phase transformation, are considered in calculating the stress distribution that develops during cooling. The plastic strain and plate-buckling, which are often shown in accelerated cooled plate, were determined from this stress. Mean temperature in through thickness direction and temperature difference in width direction are considered in the model to simplify the calculation. The temperature and stress distribution changes caused by phase transformation are involved in terms of the effective specific heat and the effective thermal expansion coefficient. With the model, accelerated cooling of 10mm(t) $^{*}$3000mm(w) plate was simulated. The condition of accelerated cooling was .deg. C/sec from just after hot rolling to 500.deg. C. The initial temperature-difference ratio, .DELTA.Tr, in width direction is an important factor in evaluating the stress distribution. When .DELTA.Tr is 0.08, buckling occurs during cooling and 7kgf/m $m^{2}$ of residual stress develops at the edge of plate. To secure the flatness, .DELTA.Tr should be less than 0.07. Small scaled cooling test was conducted to verify the exactness of the model and the results proved the usefulness of this numerical analysis model.l.

• Proceedings of the KSR Conference
• /
• 1998.05a
• /
• pp.580-587
• /
• 1998

For many decades, the railway was constructed using tracks with jointed rails of relatively short lengths in accordance with rolling and handling technology. The joints cause many drawbacks in the track and lead to significant maintenance cost. So, railroad engineers became interested in eliminating joints to increase service loads and speeds by improving rolling, welding, and fastening technology, Continuous welded rail(CWR) track has many advantages over the conventional jointed-rail track. But in the case of the elimination of rail joints, it may cause the track to be suddenly buckled laterally by thermal and vehicle loads. Thermal loads are caused by an increase in the temperature of railway track. In this paper, CWR track model and CWRB program are developed for linear buckling analysis using finite element method(FEM). The finite element discretization is used with a total of 14 degrees of freedom for each rail element. The stiffness of the fastener, tie, and ballast bed are included by a set of spring elements. The investigation on the buckling modes and temperature of CWR track is presented in the paper.