• Journal of Bio-Environment Control
• /
• v.32 no.1
• /
• pp.48-56
• /
• 2023

High-pressure sodium (HPS) lamps have been widely used as a useful supplemental light source to emit sufficient photosynthetically active radiation and provide a radiant heat, which contribute the heat requirement in greenhouses. The objective of this study to analyze the thermal characteristics of HPS lamp and thermal behavior in supplemented greenhouse, and evaluate the performance of a horizontal leaf temperature of sweet pepper plants using computational fluid dynamics (CFD) simulation. We simulated horizontal leaf temperature on upper canopy according to three growth stage scenarios, which represented 1.0, 1.6, and 2.2 plant height, respectively. We also measured vertical leaf and air temperature accompanied by heat generation of HPS lamps. There was large leaf to air temperature differential due to non-uniformity in temperature. In our numerical calculation, thermal energy of HPS lamps contributed of 50.1% the total heat requirement on Dec. 2022. The CFD model was validated by comparing measured and simulated data at the same operating condition. Mean absolute error and root mean square error were below 0.5, which means the CFD simulation values were highly accurate. Our result about vertical leaf and air temperature can be used in decision making for efficient thermal energy management and crop growth.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.238-246
• /
• 1996

High-density SiC-AIN solid solutions were fabricated from powder mixtures of $\beta$-SiC and AIN by hot-pressing in the 1870 to $2030^{\circ}C$ temperature range. The reaction of AIN and $\beta$-SiC (3C) powder transformed to the 2 H (wurzite) structure appeared to depend on the temperature and SiC/A1N ratio and seeds present. The crystalline phases consisted of a SiC-rich solid-solution phase and an A1N-rich solid-solution phase. At $2030^{\circ}C$ for 1 h, for a composition of 50 % AIN/50 % SiC with a seeding of $\alpha$-SiC, the complete solid solution could be obtained and the microstructures are equiaxed with a relatively homogeneous grain size of 2 H phases. The variation of the seeding of $\alpha$-SiC in SIC-A1N solid solutions could be attributed to the transformation behaviour and differences in size and shape of the grains, as well as to other factors, such as grain size distributions, compositional inhomogeneity, and structural defects.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.123-123
• /
• 2010

3족 질화물계 물질은 발광다이오드와 같은 광전자소자적용에 있어서 매우 우수한물 질이다.일반적으로, GaN 에피 성장에 있어서 저온 중간층을 삽입한 2 단계 성장 방법은 낮은 결함밀도와 균일한 표면을 얻기 위해 도입된 기술이다. 특히 AlN 중간층은 GaN 중간층과 비교하였을 때 결정성뿐만 아니라 높은 온도에서의 열적안정성, GaN 기반의 자외선 검출기서의빛 흡수 감소 등의 장점을 가지고 있다. 또한 패턴 사파이어 기판위 GaN 에피 성장은 측면성장 효과를 통해 결함 밀도 감소와 광 추출 효율을 향상시키는 것으로 알려져 있다.또한 열응력으로 인한 기판의 휨 현상은 박막성장중 기판의 온도 분포를 불균일하게 만드는 원인이 되며 이는 결국 박막 조성 및 결정성의 열화를 유도하게 되고 최종적으로 소자특성을 떨어 뜨리는 원인이 되는데 AlN 중간층의 도입으로 이것을 완화시킬 수 있는 효과가 있다. 하지만, AlN 중간층이 패턴된 기판 위에 성장시킨 GaN 에피층에 미치는 영향은 명확하지 않다. 본 연구팀은 일반적인 c-plane 사파이어 기판과 플라즈마 건식 에칭을 통한 렌즈 모양의 패턴된 사파이어 기판을 이용해서 AlN 중간층과 GaN 에피층을 유기금속 화학기상증착법으로 성장하였다. 특히, 렌즈 모양의 패턴된 사파이어 기판은 패턴 모양과 패턴 밀도가 성장에 미치는 영향을 연구하기 위해 두가지 패턴의 사파이어 기판을 이용하였다. AlN 중간층 두께를 조절함으로써 최적화된 GaN 에피층을 90분까지 4단계로 시간 변화를 주어 성장 양상을 관찰한 결과, GaN 에피박막의 성장은 패턴 기판의 trench 부분에서 시작하여 기판의 패턴부분을 덮는 측면 성장을 보이고있다. 또한 TEM과 CL을 통해 GaN 에피박막의 관통 전위를 분석해 본 결과 측면 성장과정에서 성장 방향을 따라 옆으로 휘게 됨으로 표면까지 도달하는 결정결함의 수가 획기적으로 줄어드는 것을 확인함으로써 고품질의 GaN 에피층을 성장시킬 수 있었다. 그리고 패턴밀도가 높고 모양이 볼록할수록 측면 성장 효과로 인한 결정성 향상과 난반사 증가를 통한 임계각 증가로 광추출 효율이 향상 되는 것을 확인할 수 있었다. 이러한 결과를 바탕으로 최적화된 AlN 중간층을 이용하여 패턴 기판위에서 고품질의 GaN 에피층을 성장시킬 수 있었다.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.40 no.9
• /
• pp.1279-1284
• /
• 2011

Gelatinization properties of crude starches from acorns harvested in various countries (domestic (KAS), Chinese (CAS), and North Korea (NAS)) were analyzed, especially blue value, amylose contents, amylogram, particle size, and SEM (scanning electron microscope). Amylose contents of NAS, KAS, and CAS were 33.65%, 32.00%, and 30.48%, respectively, and a similar tendency was observed in blue value. According to amylogram, initial paste temperature was $72^{\circ}C$ for NAS and CAS and $71^{\circ}C$ for KAS, whereas peak viscosity was 580 BU for KAS and NAS and 570 BU for CAS. The cooling viscosity and setback of NAS and CAS were higher than those of KAS. The average particle size was 23.17 microns for KAS, 23.53 microns for CAS, and 82.14 microns for NAS; particle size ranging from 5~40 microns was highly distributed in KAS (68.9%) and CAS (73.8%), whereas 57.1% distribution was observed for 5~40 microns and 27.2% for >80 microns in NAS. Gelatinization ranges of SEM photography of CAS and NAS showed a more swollen, extremely disintegrated, and folded structure than that of KAS. From these results, gelatinization properties, especially viscosity, setback of amylogram, particle size, and SEM photography, differed according to the country.

• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.535-543
• /
• 2022

A CPFD (Computational particle fluid dynamics) model of solar fluidized bed receiver of silicon carbide (SiC: average d_p=123 ㎛) particles was established, and the model was verified by comparing the simulation and experimental results to analyze the effect of particle behavior on the performance of the receiver. The relationship between the heat-absorbing performance and the particles behavior in the receiver was analyzed by simulating their behavior near bed surface, which is difficult to access experimentally. The CPFD simulation results showed good agreement with the experimental values on the solids holdup and its standard deviation under experimental condition in bed and freeboard regions. The local solid holdups near the bed surface, where particles primarily absorb solar heat energy and transfer it to the inside of the bed, showed a non-uniform distribution with a relatively low value at the center related with the bubble behavior in the bed. The local solid holdup increased the axial and radial non-uniformity in the freeboard region with the gas velocity, which explains well that the increase in the RSD (Relative standard deviation) of pressure drop across the freeboard region is responsible for the loss of solar energy reflected by the entrained particles in the particle receiver. The simulation results of local gas and particle velocities with gas velocity confirmed that the local particle behavior in the fluidized bed are closely related to the bubble behavior characterized by the properties of the Geldart B particles. The temperature difference of the fluidizing gas passing through the receiver per irradiance (∆T/I_DNI) was highly correlated with the RSD of the pressure drop across the bed surface and the freeboard regions. The CPFD simulation results can be used to improve the performance of the particle receiver through local particle behavior analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.9
• /
• pp.92-100
• /
• 2017

The Helicopter MRA Control Rod System has the important function of controlling the speed, height, and direction of helicoptersby adjusting the main rotor disc. However, the ingress of water into the inner control rod can cause ice damage in the rod during winter operation and also corrosion;these defects need to be rectified. The water flowed into the control rod through the upper side space, and the rod was cracked during icing expansion occurring at low temperature. The corrosion occurred due to the lack of coating process during the manufacturing process. To resolve these problems, the upper rod was sealed to prevent water inflow and a coating process was added to prevent corrosion. These solutions were verified by awaterproof test and a salt fog test. The phenomena, causes and measures were reviewed and the methods of improvement were established and proven. This proposed technology to prevent water infiltration and corrosion will contribute to the safety of rotary wing aircraft.

• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.103-115
• /
• 2011

Concrete slab curls and warps due to the uneven distribution of temperature and moisture and as the result, internal stress develops within the slab. Therefore, environmental loads must be considered in addition to the traffic loads to predict the lifespan of the concrete pavement more accurately. The strength of the concrete slab is gradually decreases to a certain level at which fatigue cracking is generated by the repetitive traffic and environmental loadings. In this study, a new fatigue regression model was developed based on the results from previously performed studies. To verify the model, another laboratory flexural fatigue test program which was not used in the model development, was conducted and compared with the predictions of other existing models. Each fatigue model was applied to analysis logic of cumulative fatigue damage of concrete pavement developed in the study. The sensitivity of cumulative fatigue damage calculated by each model was analyzed for the design factors such as slab thickness, joint spacing, complex modulus of subgrade reaction and the load transfer at joints. As the result, the model developed in this study could reflect environmental loading more reasonably by improving other existing models which consider R, minimum/maximum stress ratio.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.30-38
• /
• 2023

As the number of old buildings subject to safety inspection increases, the burden on designated institutions and management entities that are responsible for safety management is increasing. Accordingly, when selecting buildings subject to safety inspection, appropriate safety inspection standards and appropriate technology are essential. The current safety inspection standards for old buildings give low scores when it is difficult to confirm damage such as cracks in structural members due to finishing materials. This causes the evaluation results to be underestimated regardless of the actual safety status of the structure, resulting in an increase in the number of aging buildings subject to safety inspection. Accordingly, this study proposed a thermal imaging technique, a non-destructive and non-contact inspection, to detect cracks inside finishing materials. A concrete specimen was produced to observe cracks inside the finishing material using a thermal imaging camera, and thermal image data was measured by exciting a heat source on the concrete surface and cracked area. As a result of the measurement, it was confirmed that it was possible to observe cracks inside the finishing material with a width of 0.3mm, 0.5mm, and 0.7mm, but it was difficult to determine the cracks due to uneven temperature distribution due to surface peeling and peeling of the wallpaper. Accordingly, as a result of performing data analysis by deriving the amplitude and phase difference of the thermal image data, clear crack measurement was possible for 0.5mm and 0.7mm cracks. Based on this study, we hope to increase the efficiency of field application and analysis through the development of technology using big data-based deep learning in the diagnosis of internal crack damage in finishing materials.