• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2002년도 학술.기술논문발표회
• /
• pp.99-102
• /
• 2002

This paper discusses the estimation of construction cost of high fluidity concrete using segregation reducing type superplasicizer with 350kgf/cm2 of design strength and 60$\pm$5cm of slump flow in order to verify the cost down effect of high fluidity concrete compared with that of plain concrete with 350kgf/cm2 of design strength and 18cm of slump and with 210kgf/cm2 of design strength and 15cm of slump. According to research, under same strength levels, although material cost of high fluidity concrete is somewhat higher than that of plain concrete due to segregation reducing type superplasticizer, labor cost and equipment cost of high fluidity concrete is cheaper than that of plain concrete. However, based on the strength differences, high fluidity concrete shows lower material cost, labor cost and equipment cost than that of plain concrete due to decreasing in size of member and re-bar caused by high strength development of concrete.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.643-646
• /
• 2005

This paper reports the influence of super retarding agent(SRA) on the setting time of concrete incorporating mineral admixture including fly ash(FA), expansive additive(EA), silica fume(SF), blast furnace slag(BS) and blast furnace slag along with fly ash(BS+FA). An increase in SRA resulted in retarding the setting time of control concrete, while the use of mineral admixture led to a delay of setting time markedly, compared with that of control concrete under no SRA content. Meanwhile, An increase in SRA in concrete with mineral admixture exhibited comparable setting delay with control concrete. Furthermore, in case of the use of BS and SF, acceleration of setting time was observed with increase of SRA content. It is considered that proper dosage of SRA of concrete with SF and BS to secure similar setting delay with control concrete require rather larger than that of control concrete. Accordingly, For concrete with mineral admixture, in order to decide the proper dosage of SRA, application of correction factors is needed.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.146-147
• /
• 2014

In this study, as the resistance of the carbonation for high volume admixture incorporating concrete, coating effect of using refined cooking oil in the surface of high volume admixture incorporating concrete has been tested. The following results could be made as the conclusion. For the fresh concrete, the slump and air content has been identified as satisfying the target range. For the hardened concrete, comparing with specimen of Plain, specimen with coating showed better long age compressive strength. For the carbonation speed, the specimen of FA30 showed highest speed and the specimen of BS60 showed higher speed than specimen of Plain. For all the specimens coated with RCO, as the decrease of capillary pores inside the concrete, the carbonation speed has been obviously decreased and with even better effect than using PEP coating. It could be identified that specimens with coating by RCO showed good effect on refrain the speed of carbonation.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2003년도 학술.기술논문발표회
• /
• pp.95-98
• /
• 2003

This paper presents the results of field experiment to apply the difference of setting tine method using super retarding agent for reducing hydration heat of mass concrete of foundation. According to the results, as the properties of fresh concrete, base concrete satisfies aimed slump and air content, and there is no difference of slump and air content with mixture of super retarding agent. The mixing ratio of super retarding agent is determined for setting time to be retarded by 12 hours in comparison with base concrete, but because the temperature of the air and concrete is low, the difference of setting time is retarded to 24 hours. In man concrete of foundation to which the difference of setting time method is applied, crack by hydration heat is not seen because the lower concrete of super retarding agent generates heat after generation of hydration heat of the upper concrete.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 춘계 학술논문 발표대회
• /
• pp.13-14
• /
• 2016

This study is aimed to analyze temperature history at each section of mat foundation concrete applying double bubble sheets. The results of the study are as follows. Firstly, the results of measuring the temperature history indicate that the lowest external temperature has been recorded at -5.6℃ for the three-day measurement period. For the central section, the result indicates that the lower, center and upper part have all secured the concrete curing temperature of 18℃ or higher. This results are believed to have resulted from excellent heat insulation performance of double bubble sheets. For the edge section between the edge form and the concrete interface, the temperature has been measured, on average, approximately 12℃ lower than the central section. However, all measured sections have indicated the temperature of 5℃ or higher. Meanwhile, an analysis has been conducted through the estimation equation of compressive strength of maturity during the curing period in order to examine the possibility of early frost damage and the aspect of securing strength. It has been confirmed that the compressive strength is higher than 50°D·D, namely, 5MPa, on the 3rd day of the aging process, which allows early frost damage to be avoided.

• 콘크리트학회논문집
• /
• 제11권4호
• /
• pp.95-105
• /
• 1999

When superplasticizer is added to manufacture flowing concrete, the base concrete usually needs the adjustment to assure the sufficient fines contained to obtain flowable consistency without excessive bleeding or segregation. However, this may not only increase the cost, but also cause inconvenience in producing the base concrete. In this paper, the experiments are performed on normal base concrete to achieve a segregation-reducing flowing concrete by adding superplasticizer mixed with viscosity agents and AE admixtures. Three kinds of superplasticizer and two kinds of viscosity agent are selected. According to the results, with regard to the performance and cost of the admixtures, melamine type superplasticizer combined with the PEO viscosity agent and AE admixtures at the ratio 1:0.28:0.001 can acquire good quality and reduce the cost in producing the flowing concrete. With proper addition of combined superplasticizer, even though water to cement ratios of the base concrete are different, the segregation-reducing flowing concrete could be also achieved without reproportioning of the base concrete. However, it would be more desirable if the superplasticizer could be adjusted, before it is put into the practical use in order not to cause some other problems, such as rapid rate of slump loss and retarding of setting time.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.505-508
• /
• 2004

This paper investigated the setting and compressive strength of concrete with the combination of mineral and chemical admixture. According to test results, plain concrete with high early strength development type AE water reducing agent(HEAEWRA) and $10\%$ of CKD respectively had earlier setting time than concrete with AE water reducing agent by $0.5\~1.5$ hours. Setting time of concrete with retarding type AE water reducing agent(RAEWRA) and FA $30\%$, BS $60\%$ respectively retarded by as much as $4\~7.5$ hours compared with plain concrete. Plain concrete with HEA WRA, $10\%$ of CKD and RAEWRA had higher strength than that of AE water reducing agent by as much as 5MPa at 28days. From the result of the paper, it is found that the combination of mineral admixture and setting accelerating or retarding agent can reduce the hydration heat cracks by setting time difference and hydration heat reduction effects.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2006년도 춘계학술논문 발표대회 제6권1호
• /
• pp.15-18
• /
• 2006

The test result of mat concrete applying both hydration heat difference and insulation curing method on new construction of Cheongju university educational building are summarized as following. Both fresh concrete and compressive strength properties were satisfied In aimed value. Setting time of concrete incorporating 15% of fly ash(FA) retarded 1.2 hour than control concrete. Temperature history of mali concrete indicated that the highest temperature of center was exhibited at $126^{\circ}C$ after 51 hours while the highest temperature of upper section was $10.6^{\circ}C$ after 46 hours. Temperature Difference between center and surface was managed at less than $6^{\circ}C$ during whole curing period. In addition the temperature of upper section secured more than $3.3^{\circ}C$ while the temperature of outside was indicated at less than $-10^{\circ}C$. Maturity by parts of construction secured more than $30^{\circ}C$ DD higher than outside at 3 days. The more number of times, applying insulation curing method by double bubble sheets, increased, the higher economic effect was secured. Overall it was clear that applying both double bubble sheets and hydration heat difference method on this new construction can resist hydration heat crack, early frost demage and strength decrease. It also significantly contributed quality improvement of cold weather concreting

• 콘크리트학회논문집
• /
• 제14권1호
• /
• pp.16-23
• /
• 2002

우리나라의 건설공사 현장에서는 해마다 수백만톤의 콘크리트 폐기물이 배출되고 있다. 이를 효율적으로 재활용할 경우는 환경파괴를 방지할 뿐만 아니라 경제적으로도 큰 효과를 기대할 수 있다. 하지만 기존의 콘크리트 폐기물에 관한 재활용 방법으로는 성토, 잡석다짐, 매립 등의 일부용도에만 사용될 뿐 폭넓게 활용하기에는 한계가 있었다. 따라서 본 연구에서는 골재로 재활용할 수 있는 다양한 종류의 건축폐기물을 환경친화적인 식재용 콘크리트에 이용하여 강도, 내구성 등의 물리적 특성을 검토하였다. 연구결과, 재생골재를 이용한 식재용 콘크리트의 물성은 부순돌에 비하여 압축강도, 동결융해 저항성면에서는 다소 불량하게 나타났지만, 흡수율과 열전도율면에서는 우수한 효과도 입증되었고, 특히 콘크리트 폐기물의 효율적인 재활용 측면을 고려한다면 식재용 콘크리트로의 활용가치는 충분이 있는 것으로 사료된다.

• 콘크리트학회논문집
• /
• 제15권3호
• /
• pp.392-399
• /
• 2003

본 연구는 한중콘크리트 시공 시 초기보온 대책 중 가장 손쉽고 경제적일 것으로 사료되는 단열 보온양생을 대상으로 하였다. 실험은 한중콘크리트 시공조건을 상정하여 기존 거푸집과 각종 단열재 조합에 따른 단열거푸집간의 온도이력을 검토하여 효율적인 단열거푸집을 개발하고자 하였다. 실험결과 $-10^{\circ}C$ 일정인 외기온도 조건에서 벽용 거푸집의 경우, 일반 유로폼인 경우는 초기 24시간 이전에 급속한 온도저하에 의해 $0^{\circ}C$ 이하로 약 7시간 정도 지속되었고, PP＋스티로폼＋합판인 경우는 영상의 온도를 유지하고, 강도발현도 우수하며, 단열거푸집간 비교적 가격도 저렴하여 우수한 단열거푸집임이 밝혀졌다. 슬래브용 거푸집 실험의 경우, 하부는 단열거푸집으로 고정하고, 콘크리트 표면 양생방법을 달리하였을 때, 콘크리트의 온도이력을 측정한 결과, 노출시킨 경우 약 10시간 이후부터 영하로 저하하였고, 비닐+양생포의 경우 약 42시간 이후부터 영하로 저하하였다. 반면, 비닐＋스티로폼+양생포를 사용한 양생의 경우에는 약 55시간 이후부터 영하로 저하하여 노출이나 일반적으로 많이 사용되는 비닐＋양생포와 비교하여 우수한 단열효과임이 밝혀졌다. 7일 및 28일에 있어 슬래브의 코어 압축강도를 측정한 결과는 단열재를 사용하였을 때 크게 나타났다.