• 대한기계학회논문집B
• /
• 제23권9호
• /
• pp.1185-1191
• /
• 1999

Radiation-induced oscillatory instability in diffusion flames is numerically investigated with nonlinear dynamics considered. As the simplest flame model, a diffusion flame established in the stagnant mixing layer is employed with optically thin gas-phase radiation and unity Lewis numbers for all species. Attention is focused on the radiation-induced extinction regime, which occurs at large $Damk\ddot{o}hler$ number. Once the steady flame structure is obtained for a prescribed value of the initial $Damk\ddot{o}hler$ number, transient solution of the flame is calculated after a finite amount of the $Damk\ddot{o}hler$-number perturbation is imposed on the steady flame. Transient evolution of the flame exhibits three types of flame-evolution behaviors, namely decaying oscillatory solution, diverging solution to extinction and stable limit-cycle solution. A dynamic extinction boundary is identified for laminar flamelet library.

• 한국연소학회지
• /
• 제17권3호
• /
• pp.9-16
• /
• 2012

Nonlinear dynamics of pulsating instability in radiating counterflow diffusion flames is numerically investigated by imposing Damk$\ddot{o}$hler number perturbation. Stable limit-cycle solutions occur in small ranges of Damk$\ddot{o}$hler numbers past bifurcation point of instability. Period doubling cascade and chaotic behaviors appear just before dynamic extinction occurs. Nonlinear dynamics is also studied when large disturbances are imposed to flames. For weak steady flames, the dynamic extinction range shrinks as the magnitudes of disturbances are increased. However, strong steady flames can overcome relatively large disturbances, thereby the dynamic extinction range extending. Stable limit-cycle behaviors reappears prior to dynamic extinction when the steady flames are strong enough.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제26회 춘계학술대회논문집
• /
• pp.7-10
• /
• 2006

본 논문에는 준평형 모델을 사용하는 PAD(propellant actuated device) 시스템의 거동 및 추진제 형상설계에 관하여 기술하였다. 준평형 모델의 검증을 위해 PAD 시스템 시험이 수행되었다. 시험과 해석 결과를 비교하여 상호 경향이 유사함을 확인함으로써 준평형 모델적용치 타당성을 입증하였고, 사용된 시스템의 열손실 및 마찰계수를 얻을 수 있었다. 개발된 설계기법은 향후 PAD 시스템 설계시에 유용하게 사용될 것이다.

• 대한기계학회논문집B
• /
• 제25권1호
• /
• pp.29-35
• /
• 2001

Radiation-induced oscillatory instability in CH$_4$/Air diffusion flames is numerically investigated by adopting detailed chemistry. Counterflow diffusion flame is employed as a model flamelet and optically thin gas-phase radiation is assumed. Attention is focused on the extinction regime induced by radiative heat loss, which occurs at low strain rate. Once a steady flame structure is obtained for a prescribed value of initial strain rate, transient solution of the flame is calculated after a finite amount of strain-rate perturbation is imposed on the steady flame. Depending on the initial strain rate and the amount of perturbed strain rate, transient evolution of the flame exhibits various types of flame-evolution behaviors. Basically, the dynamic behaviors can be classified into two types, namely oscillatory decaying solution and diverging solution leading to extinction.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.131-136
• /
• 2001

In this paper, a high-temperature superconductor(HTS) current lead operating in current sharing mode is described. The minimum heat dissipation and the optimum safety factor(cross-sectional area) is obtained analytically for partial current sharing HTS leads. It is assumed that the current lead is in conduction cooled state, and the sheath material is the alloy of silver and gold. The reduced cross-sectional area results partial current sharing state, and consequently reduces conduction heat transfer, but the Joule heat generation is increased. The optimized HTS current lead is different from the conventional copper leads. In the copper leads, the minimum heat dissipation is obtained for the zero gradient of temperature at warm end. However, the temperature gradient at warm end is not zero when the HTS lead operates at minimum dissipation state.

• 산업기술연구
• /
• 제21권A호
• /
• pp.33-40
• /
• 2001

Heat loss from the trapezoidal fins haying different upper side slope and that from a rectangular fin are investigated by the three dimensional analytic method. It is shown that the trapezoidal fins having different upper side slope become an approximate rectangular fin by inst adjusting the slope factor. The comparison of the heat loss between a rectangular fin and an approximate rectangular fin is represented as a function of the non-dimensional fin length, fin width and Biot number to make sure that the analysis on the trapezoidal fins having different upper side slope is countable. One of the results is that the relative value of heat loss between a rectangular fin and an approximate rectangular fin is less than 1.5% for given ranges of non-dimensional length and width in case of Bi = 0.1.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권6호
• /
• pp.871-879
• /
• 1998

The refrigerator consists of many components such as compressor condenser expansion valve evaporator and the cabinet which filled by urethane foam. In this paper the heat leakage of refriger-ator is measured by the new experiment method which is different from a present method, The devi-ation of the UA(overall heat transfer coefficient times area) between the simulation and experiments is about 7-8%. Using the modeling of various components of refrigeration system a performance analysos of CFC 12 and HFC 134a is performed numerically on the UA. As the results of this study according to increase the heat leakage the refrigeration load and mass flow rate of refrigerant are increased. And the increase of the mass flow rate results in the increase of the condensing and evapo-rating temperature. Therefore according to increase of the heat leakage the COP leads to increase because the increase of refrigeration capacity is larger than the increase if compressor power.

• 한국연소학회지
• /
• 제6권1호
• /
• pp.14-19
• /
• 2001

Interests and importance of down-scale combustor is increasing with the emerging need for miniaturized power source which is now a bottleneck of micro system development. But in down scaled combustor increased heat loss compared to thermal energy generation inhibits the usability and application of the device, so as a preliminary work of down scaled combustor fabrication. Modeling tool for the device should be established, in this study modeling approach of closed vessel combustion phenomena that can express heat loss effect and resulting quenching is proposed and the result is compared with experiment data. From this model heat loss effect following combustor scale down can be further understood, and further more design parameter and analysis tool can be obtained.

• 대한기계학회논문집
• /
• 제19권11호
• /
• pp.2995-3002
• /
• 1995

The cooling problem of the hot internal pipe flow has been investigated. Simultaneous conduction, convection, and radiation were considered with azimuthally varying convective heat loss at the pipe wall. A complex, nonlinear integro-differential radiative transfer equation was solved by the discrete ordinates method (or called S$_{N}$ method). The energy equation was solved by control volume based finite difference technique. A parametric study was performed by varying the conduction-to-radiation parameter, optical thickness, and scattering albedo. The results have shown that initially the radiatively active medium could be more efficiently cooled down compared with the cases otherwise. But even for the case with dominant radiation, as the medium temperature was lowered, the contribution of conduction became to exceed that of radiation.n.

• 대한의용생체공학회:의공학회지
• /
• 제22권1호
• /
• pp.35-40
• /
• 2001

압력기반의 유한체적법과 k-$\varepsilon$난류모델을 이용하여 신생아 보육기 내의 삼차원 정상난류유동해석과 대류현상에 의한 열전달을 해석하였다. 보육기 내의 주된 공기유동은 입구에서 유입된 공기가 보육기 위쪽을 지나 출구로 이동하며 각진 구석에서 작은 와류들이 관찰되었다. 보육기의 입구부를 제외한 대부분에서의 유속은 0.1m/s 이하로 나타났으며, 신생아의 다리부분에서의 속도가 머리부분보다 다소 크게 관찰되었다. 입구쪽의 온도가 출구쪽의 온도보다 1~2$^{\circ}C$ 높게 나타났으며 속도 크기가 큰 다리부분에서의 온도가 머리 또는 목부분보다 다소 낮았다. 보육기 내의 온도변화는 약3~4$^{\circ}C$로 다소 크게 나타났는데 이는 입구에서 유입된 공기가 상벽과 직각으로 만나며, 보육기 외벽의 각진 구석부분에 의한 영향으로 생각된다. 따라서 입구속도를 적절히 줄이거나 유선형의 유동을 갖도록 설계하여 열손실을 최소화한다면 보다 효율적인 보육기가 될 것으로 생각된다.