• Tunnel and Underground Space
• /
• v.12 no.3
• /
• pp.220-228
• /
• 2002

Thermal flow through jointed rock mass was analyzed by numerical methods. The effect of a single set of joints on the heat conduction was analyzed by one-dimensional model and compared with the analytical solution. When a joint is completely dry, the joint behaves as a thermal break inducing jumps in temperature distribution even at steady state. Therefore when joints are completely dry, individual joint has to be taken into consideration to get a good result. When joints are partially or fully saturated, the thermal conductivity of the joints increases drastically and the jumps in temperature distribution become less severe. Therefore the effect of joint in heat conduction can be well absorbed by continuum anisotropic model whose thermal properties represent overall thermal properties of the intact part and the discontinuities. Since the effect of joints becomes less important as the degree of the saturation increases, the overall thermal response of the rock mass also becomes close to isotropic. Therefore it can be concluded that a great effort has to be made to obtain a precise in-situ thermal properties in order to get a good prediction of the thermal response of a jointed rock mass.

• Journal of Sensor Science and Technology
• /
• v.5 no.2
• /
• pp.37-46
• /
• 1996

This paper describes a system that can be used to recognize unknown materials regardless of the change in ambient temperature by using temperature response curve fitting and fuzzy neural network(FNN). There are problems with a recognition system which utilize temperature responses. It requires too many memories to store the vast temperature response data and it has to be filtered to remove the noise which occurs in experiments. Thus, this paper proposes a practical method using curve fitting to remove the above problems of memories and noise. Also, the FNN is proposed to overcome the problem caused by the change of ambient temperature. Using the FNN which is learned by temperature responses on fixed ambient temperatures and known thermal conductivity, the thermal conductivity of the material can be inferred on various ambient temperatures. So the material can be recognized via its thermal conductivity.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.17-24
• /
• 1993

사출성형 문제는 열전달과 유체유동이 복합된 문제라고 할수 있다. 사출성형 공정은 충진(filling), 보압(packing) 및 냉각과정(cooling phase)으로 이루어 진다. 충진과정은 높은 점성의 Non-Newtonian유체가 몰드내의 캐버티로 사출됨으로써 이루어지며 플라스틱의 점성도는 플라스틱의 온도 및 유동속도와 관련이 크며 이 flow-rate는 점도와 더불어 변화한다. CAE 유동해석 프로그램은 유체의 흐름과 열전달을 이용하여 충진과정을 이해하는데 이용되고 있다. 본 고에서는 사출성형 과정 중 충진과정에 대한 컴퓨터 시뮬레이션과 그 적용사례에 대하여 살펴본다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.225-230
• /
• 1998

DUPIC 핵연료 소결체의 하나로 조사시험과 관련하여 이중 피복관으로 구성된 소결체 설계를 수행하였으며 각각의 설계변수가 핵연료의 온도에 미치는 영향하였다. 하나로에서 조사할 DUPIC 핵연료의 설계해석 결과, DUPIC 핵연료의 조사시험시 열전도도, 출력, 반경 틈새 등은 핵연료의 온도에 크게 영향을 미쳤으며, 피복재 두께, gamma열, 열전달 계수 등은 핵연료의 온도에 크게 영향을 미치지 않았다. Transient 온도분석의 경우 약 160초 이상의 시간에서 평형 온도에 도달할 것으로 분석되었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.28-35
• /
• 2016

The in-situ thermal response test for the design of a ground heat exchanger of geothermal heat pumps have difficulty in predicting the outlet temperature according to the variation of conditions due to the expense and time. This paper suggests a 3-D CFD analysis method to predict the heat transfer performance of vertical type ground heat exchanger, which is mostly used in national, and the outlet temperature and the slope of two in-situ thermal response tests were compared to test the proposed CFD reliability. The results of CFD analysis showed that the outlet temperature was predicted to within $0.5^{\circ}C$ of the actual value and the slope was predicted to within 1.6%. The reliability of the CFD analysis method was confirmed using this process, and the outlet temperature prediction of the two in-situ thermal response tests was obtained by changing ${\pm}20%$ of the flow rate and the effective thermal conductivity conditions, respectively. The results of CFD analysis showed that the outlet temperature of Case 1 was 28.0 (-20%) and $29.6^{\circ}C$ (+20%) for the flow rate variation and $29.6^{\circ}C$ (-20%) and $28.0^{\circ}C$ (+20%) for the effective thermal conductivity variation, and the outlet temperature of Case 2 was 28.4 (-20%) and $29.8^{\circ}C$ (+20%) for the flow rate variation and $29.7^{\circ}C$(-20%) and $28.4^{\circ}C$(+20%) for the effective thermal conductivity variation.

• Journal of Energy Engineering
• /
• v.20 no.4
• /
• pp.303-308
• /
• 2011

The present study has been carried out to predict the heat transfer characteristics of reverse heat loss method for a residential refrigerator by using numerical analysis and corresponding experiment. From the measured values of temperature and heat input, one can conclude that, the temperature inside the refrigerator has a nearly linear relationship with heat input. The effect of gasket heat loss was examined with the change of thermal conductivity of gasket region. The appropriate thermal conductivity of gasket region was acquired from the comparison of heat losses with the experimental result and numerical analysis. The result of calculated heat losses had accuracy within 1.8% error with the experimental result. With the selected thermal conductivity of gasket region, the effectiveness of reverse heat loss method was examined with the change of thermal conductivity of vacuum insulation panel.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.326-329
• /
• 2000

Study of Weldment fracture behavior mcludes thermal analysis, residual stress analysis, and fracture analysis The 1-integral loses its path-independency in a res~dual stress field Therefore, it id necessary to develop a program to calculate the J-integral in a welded plate. m this study, theoretical formulation and program were developed for the evaluation of the 1-integral at the crack tip o i weldments. To verify equations and program, welded thin plate and thick plate were used to calculate residual stress and the J-integral.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.12
• /
• pp.2253-2258
• /
• 2008

To design micro flow sensor varying depending on temperature of driving heater in the detector of Oxide semiconductor, Markov chain MCM(MCMCM), which is a kind of stochastic and microscopic method, was introduced. The formulation for the thermal transfer equation based on the FDM to obtain the MCMCM solution was performed and investigated, in steady state case. MCMCM simulation was successfully applied, so that its application can be expanded to a three-dimensional model with inhomogeneous material and complicated boundary.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.268-273
• /
• 1997

사용후핵연료는 장기간 강한 방사선과 붕괴열이 방출된다. 따라서 사용후핵연료를 안전하게 운반하기 위하여 수송용기는 방사선차폐의 건전성, 격납경계의 유지 및 내부 붕괴열의 적절한 제거 등의 설계기준을 만족하도록 설계되어야 한다. 본 연구에서는 28개의 PWR 사용후핵연료집합체를 운반할 수 있는 KSC-28 수송용기의 적절한 열전달 특성을 갖는 copper 냉각핀 및 aluminum 전열판을 설정하였다. 또한, 정상수송조건 및 화재사고조건에 대한 열전달해석을 수행하여 수송용기의 열적 건전성을 평가하였고 여기에서 얻어진 온도를 열하중으로 고려하여 열응력해석을 수행함으로써 수송용기의 온도변화에 따른 구조적 건전성을 평가하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.3
• /
• pp.249-257
• /
• 2015

A fuel assembly consists of fuel rods composed of pellets (UO2) and a cladding tube (Zircaloy). The role of the fuel rods in the reactor is to generate heat by nuclear fission, as well as to retain fission products during operation. A simulation method using a computer program was used to evaluate the safety of the nuclear fuel rods. This computer program has been called the fuel performance code. In the analysis of a light water reactor fuel rod, the gap conductance, which depended on the distance between the pellets and cladding tube, mainly influenced the thermomechanical behavior of the fuel rod. In this work, a 3D gap element was proposed to simulate the thermo-mechanical behavior of the nuclear fuel rod, considering the gap conductance. To implement the proposed 3D gap element, a 3D thermo-mechanical module was also developed using FORTRAN90. The asymmetric characteristics of the nuclear fuel rod, such as the MPS (missing pellet surface) and eccentricity, were simulated to evaluate the proposed 3D gap element.