• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.820-823
• /
• 2017

This study experimentally investigate how the Reynolds number affect cavitation performance in a turbopump inducer using water. Cavitation performance has been determined by the static pressure measured at the inlet of the inducer. Reynolds number has been varied by varying water temperature and inducer rotational speed to maintain constant non-dimensional thermal parameter. At low non-dimensional thermal parameter, the critical cavitation number is insensitive to Reynolds number. However, at high non-dimensional thermal parameter, the critical cavitation number increased as Reynolds number increases. Thus, cavitation performance is deteriorated as Reynolds number increases when thermal effect exists.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.40-40
• /
• 2003

일반적으로 액티브 매트릭스 구동용 스위칭 소자의 경우 Turn-on 시간은 프레임 주파수와 게이트 라인의 수에 반비례하므로 LCD의 화면이 대면적으로 갈수록 스위칭 주파수는 증가하고 이는 채널에서의 열적 효과(thermal effect)를 유도하게 된다. 그러므로 전도성 유기물이 LCD용 유기박막트랜지스터(Thin Film Transistor) 등의 부품으로서의 적절성을 판단하기 위하여는 이에 대한 열적 특성에 대한 검증이 필요하게 된다. 따라서 본 연구에서는 유기 TFT의 열설계에 있어서 필수적인 물질변수로 인식되는 열적 특성들을 측정 계산하였으며 이를 소자의 열적 모델링에 적용하였다. 실험물질로는 pentacene을 사용하였으며 열확산도는 레이저 플레쉬법을 이용하여 측정하였다. 별도로 측정된 비열ㆍ밀도 등의 물성특성을 이용하여 상온에서 200 C의 온도범위에서 pentacene의 열전도도를 계산하여 그 결과를 열적으로 해석하였다. 계산결과, pentacene의 열전도도는 상온에서 약 0.0024 W/cm K의 값을 나타내었고, 70 C 까지 증가하여 약 0.0035 W/cm K의 정점을 보인 후에 200 C 에서 약 0.0022 W/cm K의 낮은 값을 나타낼 때까지 계속 감소하였다 아울러 본 연구에서는 실제 소자응용 시 박막으로서의 pentacene의 응용을 고려하여 실제 박막형태에 대한 열전도를 측정하였으며 이를 레이저 플레쉬법으로 측정한 값과 비교ㆍ분석하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.4
• /
• pp.570-578
• /
• 1997

At design stage of new motor or when taking remedial action of old motor, a lot of information can be obtained from thermal parameters analysis. This study focused on the temperature rise of TEFC induction motor with respect to various thermal parameters. Frame heat transfer had the most important effect on coil temperature rise. But those of air gap and rotor fan had no effect. This fact shows fan action is more important than fin action in the case of rotor fan. Coil temperature can be more decreased by cooling near the heat sources than any other parts from the results of thermal conductivity and loss tests. Variation of cooling air flow rate and motor volume effects on coil temperature were also tested. These tests suggest that improvement of cooling fan performance is important in reducing the coil temperature rise. Thermal equivalent program was verified by comparison of some experimental results.

• The Korean Journal of Rheology
• /
• v.10 no.2
• /
• pp.74-81
• /
• 1998

사출성형품의 설계는 그 내부의 기계적 물성 변화보다는 전통적으로 용도에 부합하 는 형상을 위주로 하여 이루어져 왔기 때문에 설계조건의 개선을 통하여 성능이 우수한 제 품을 얻기까지 많은 시행착오가 요구되고 있다. 그런데 사출성형 실험이나 물성평가 시험을 하기 전에 성형품의 부위별 기계적 물성을 알수있다면 제품의 설계나 금형 설계에 많은 도 움이 될 수 있으므로 최근에 물성 예측을 위한 방법론들의 개발이 다양하게 시도되고 있다. 따라서 본 연구에서는 학습시스템, 사출성형 수치모사와 기계적 물성과의 상관관계를 밝히 는 방법을 만들어 사출물이 제작되기 전에 그들의 기계적 물성을 사출성형 수치모사에서 얻 어진 열적·기계적 이력으로부터 예측하고자 하였다. 이때 성형품의 기계적 물성과 열적· 기계적 이력 사이에는 매우 복잡하고 비선형적인 상관관계를 보이기 때문에 이들 사이를 비 매개변수적으로 연관짓기 위하여 역전파 인공신경망 알고리듬을 사용하였으며 열적·기계적 이력은 사출성형용 수치모사 소프트웨어를 이용하여 구하였다. 학습과정에서 전역최소값에 도달하지 못하는 인공신경망의 문제점을 해결하기 위하여 모멘텀변수와 잡음지수를 포함하 는 일련의 항을 첨가하여 연결가중치를 보정하였다. 그 결과 어떤 초기값에 의하여 학습이 되더라도 전역최소값에 도달하는 것을 확인하였으며 이를 이용하여 다른 사출조건에서 사출 물의 기계적 물성을 잘 예측할수 있었다.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.39-40
• /
• 2007

본 논문은 Slotless BLDCM의 발열특성에 고려하여 열 발생을 최소화 하고자 다중 반응표면법을 적용하여 모터의 형상 및 권선 사양의 최적 선정에 관한 연구이다. 본 연구에서는 전류밀도의 최소화를 목적함수로 하여 형상 및 권선 사양의 최적화를 실시하였다. 변수에 대한 영향도의 분석은 전자계 해석을 통한 결과값을 통하여 실시하였으며, 열적 특성을 파악하기 위해서 전자계-열계의 해석을 통해서 최적값의 열적 안정성을 파악하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.9
• /
• pp.89-96
• /
• 2006

In this study, fluid flow and thermal characteristics in a catalyst bed for nitrous oxide catalytic decomposition which is introduced as a hybrid rocket ignition system for small satellites were theoretically considered. To analyze the thermal phenomena of the catalyst bed, a so-called porous medium approach has been opted for modeling the honeycomb geometry of the catalyst bed. Using a Brinkman-extended Darcy model for fluid flow and the one-equation model for heat transfer, the analytical solutions for both velocity and temperature distributions in the catalyst bed are obtained and compared with experimental data to validate the porous medium approach. Based on the analytical solutions, parameters of engineering importance are identified to be the porosity of the catalyst bed, effective volumetric ratio, the ratio of the radius of the catalyst bed to the radius of a pore, heat flux generated by a heater, and pumping power. Their effects on thermal phenomena of the catalyst bed are studied.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.693-695
• /
• 2003

차단기내에서 일어나는 아크철상을 모의하기 위해서는 수학적으로 표현할 수 있어야 한다. 하지만, 아크의 물리적 현상이 대단히 복잡하여 수식화 하기가 쉽지 않을 백만 아니라 논리적으로 이상이 없는 결과를 얻는 일도 쉽지 않다. 특히, 아크를 표현하는 수식에는 많은 경험적 변수 또는 실험결과를 고려하여 조정되어야 할 변수가 존재한다. 그 대표적인 것이 난류 변수(turbulence parameter)와 방사에너지 전달에서의 방사계수(emission coefficient)이다. 본 논문은 차단기가 전류차단 후의 열적회복과정에서, 난류변수에 따른 아크-후 전류(post arc current)를 계산한 결과를 제시한 것이다. 난류변수에 따른 아크의 냉각효과를 검토하고 있으며, 실험결과 비교하여 가장 잘 맞는 난류변수의 값을 제시하고 있다.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.30 no.4
• /
• pp.5-13
• /
• 2022

The current environmental problem is that environmental pollution is accelerating due to the generation of large amounts of waste and indiscriminate consumption of energy. Fossil fuels, a representative energy production fuel, are burned in the process of producing energy, generating a large amount of greenhouse gases and eventually causing climate change. In addition, the amount of waste generated worldwide is continuously increasing, and environmental pollution is occurring in the process of waste treatment. One of the methods for simultaneously solving these problems is the energy recovery from and reduction of organic wastes. Sewage sludge generated in sewage treatment plants has been treated in various ways since ocean disposal was completely prohibited, but the amount generated has been continuously increasing. Since the sewage sludge contains a large amount of organic materials, it is desirable to recover energy from the sewage sludge and reduce the final discharged waste through anaerobic digestion. However, most of the excess sludge is a mass of microorganisms used in sewage treatment, and in order for the excess sludge to be anaerobically digested, the cell walls of the microorganisms must be destroyed first, but it takes a lot of time to destroy the cell walls, so high rates of biogas production and waste reduction cannot be achieved only by anaerobic digestion. Therefore, the pre-treatment process of solubilizing excess sludge is required, and the thermal solubilization process is verified to be the most efficient among various solubilization methods, and high rates of biogas production and waste reduction can be achieved by anaerobic digestion after destroying cell walls the thermal solubilization process. In this study, when pretreating TS 10% thickened excess sludge through a thermal solubilization system, a study was conducted on solubilization characteristics according to retention time and operating temperature variables. The experimental variables for the retention time of the thermal solubilization system were 30 minutes, 60 minutes, 90 minutes, and 120 minutes, respectively, while the operating temperature was fixed at 160℃. The soulbilization rates calculated through TCOD and SCOD derived from the experimental results increased in the order of 12.11%, 20.52%, 28.62%, and 31.40%, respectively. And the variables according to operating temperature were 120℃, 140℃, 160℃, 180℃, and 200℃, respectively, while the operating retention time was fixed at 60 minutes. And the solubilization rates increased in the order of 7.14%, 14.52%, 20.52%, 40.72%, and 57.85%, respectively. In addition, TS, VS, T-N, T-P, NH₄⁺-N, and VFAs were analyzed to evaluate thermal solubilization characteristics of thickened excess sludge. As a result, in order to obtain 30% or more solubilization rate through thermal solubilization of TS 10% thickened excess sludge, 120 minutes of retention time is required when the operating temperature is fixed to 160℃, and 170℃ or more of operating temperature is needed when the operating time is fixed to 60 minutes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.9
• /
• pp.3125-3134
• /
• 2010

Three-way catalyst durability in the Korea requires 5 years/80,000km in 1988 but require 10 years/120,000km after 2002. Domestic three-way catalyst satisfies exhaust gas conversion efficiency or pressure drop etc. but don't satisfy thermal durability. Three-way catalyst maintains high temperature in interior domain but maintain low temperature on outside surface. This study evaluated thermal durability of three-way catalyst by thermal flow and structure analysis and the procedure is as followings. Thermal flow parameters ranges were determined by vehicle test and basic thermal flow analysis. Response surface for rear catalyst temperature was constructed using the design of experiment (DOE) for thermal flow parameters. Thermal flow parameters for rear catalyst temperature in vehicles examination were predicted by desirability function. Temperature distribution of three-way catalyst was estimated by thermal flow analysis for predicted thermal flow parameters.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.189-193
• /
• 2005

Thermal effect of finite-rate chemistry on linear combustion stability and film cooling effect are investigated in sample rocket engine. The flow variables required to evaluate stability limits are obtained from CFD data with finite-rate chemistry adopted in three dimensional chamber. Major flow variables are affected appreciably by finite-rate chemistry and thereby, the calculated stability limits are modified. It is found that finite-rate chemistry contributes to stability enhancement in thermal point of view. And film cooling also has the effect of combustion stabilization.