• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.04b
• /
• pp.126-132
• /
• 1996

A laboratory scale hot strip rolling wear simulator(HRWS) was developed for the purpose of investigating the tribological phenomena occurred in production hot strip rolling mills. The HRWS' main parts are the electric heater, the mechanical descaler, tandem type 2-4Hi rolling mill stands, the cooling chamber, the tension controller and coiler. By simulating the tribelogical phenomena in rolling process at laboratory, wear patterns, cracks, cat-ear wear, black film, effect of hot rolling oil lubrication, etc. were reproduced, and discussed on the performace of simulator.

• 발명특허
• /
• v.6 no.2 s.60
• /
• pp.54-54
• /
• 1981

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.9
• /
• pp.1117-1125
• /
• 2013

A finite element based approach that can be used to investigate the plane-view shape and crop loss of a material during plate rolling is presented. We employed a three-dimensional finite element model to continuously simulate the shape change of the head and tail of a plate as the number of rolling passes increases. The main feature of the proposed model lies in the fact that the multistage rolling can be simulated without a break because the rolling direction of the material is reversibly controlled as the roll gap sequentially decreases. The material constants required in the finite element analysis were experimentally obtained by hot tensile tests. We also performed a pilot hot plate rolling test to verify the usefulness of the proposed finite element model. Results reveal that the computed plane-view shapes as well as crop losses by the proposed finite element model were in good agreement with the measured ones. The crop losses predicted by the proposed model were within 5% of those measured from the pilot hot plate rolling test.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.7
• /
• pp.1597-1603
• /
• 1995

A prediction model on forward slip has been developed for presetting rolling speed of each finish mill stand in the continuous hot strip roduction. Those factors such as neutral point, friction coefficient, volume fractions undergoing width spread, shape of deformation zone at each side of entry and delivery of the rolls were taken into account. To reduce the speed unbalance between adjacent stands a refining method of adjusting friction coefficient has also been developed. On-line application of the model showed a good agreement in rolling speeds between the predictions and the actual measurements, and gave an outstanding improvement in the travelling stability of strip passing through the finishing mill train.

• Transactions of Materials Processing
• /
• v.5 no.3
• /
• pp.232-238
• /
• 1996

A dynamic mill set-up technique was developed to achieva a more precise roll gap set-up of the finishing mill stands for steel strip rolling. In the conventional mill set-up model the set-up values such as roll gap and roll speed are determined before the sheet bar reached the entry side of the finishing mill train and maintained constant until the strip top end passes through the last stand. In the way however a dynamic set-up logic that gives a way to adjust the roll gap value of the final mill stand for the strip ingoing from the ahead of the front stand was developed and attached to the existing set-up model. The roll gap modification is based on the analysis of the observation in the third stand of the finishing mill train. The dynamic set-up model was proved very effective for the more precise mill set-up and for operational stability in the hot strip finishing mill train.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.544-548
• /
• 2007

In general, final width of hot strip should be accomplished in this stage because width reduction of strip hardly appears during typical finishing mill. However, it is difficult to control the width of strip in the roughing mill process as the horizontal rolling of strip is subsequently performed after the vertical rolling. It is therefore important to obtain the deformation rolling direction on strip width to minimize the width spread of strip during horizontal rolling after vertical rolling. Generally there is Sizing press type and Edger-roll type. The width reduction process in sizing press has small amount of width spread compared with the edger. However, productivity by the sizing press process is much lower than those of the edger. In this study, sizing press and Edger-roll process parameters in a sheet rolling mill were set at specified values and the effect of the change in these parameters on product quality and process performance were evaluated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.8
• /
• pp.2468-2479
• /
• 1996

An upper bound solution is obtained to perform the process analysis of hot strip rolling process. The material flows within the roll bite at various geometries and frictional conditions are obtained from finite element analysis and the typical flow pattern which is necessary to determine the kinematically admissible velocity field is assumed. From the kinematically admissible velocity field, the upper bound energy is calculated and the rolling load, angle of neutral point and forward slip ratio at various operational conditions are obtained from upper bound energy. The process analysis of above mentioned parameters at various operational conditions have provided valuable information which is hard to obtain during rolling operation and the predicted ranges of quantitive values from these analyses lie whthin the bound of actual operational data.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.1
• /
• pp.134-140
• /
• 1998

포항제철 2열연공장의 사상압연에 사용되고 있는 DC 모터를 가지는 열간압연 구동기에 대한 견실 H/sup .inf./ 속도제어기 설계방법을 제안한다. 기존에는 PI 재어기법을 이용하여 속도를 제어하고 있으므로 불확실성과 외란등이 존재할 경우 양호한 제어 성능을 얻기 힘들다. 이를 해결하기 위해 주파수 하중 함수를 가지는 혼합감도최소화 문제를 설정하여 견실성을 보장하는 H/sup .inf./ 속도제어기를 설계한다. 이때 주파수 하중함수는 루프쉐이핑기법을 이용하여 주어진 구동기 플랜트에 적합하도록 선택한다. H/sup .inf./ 속도제어기 설계는 Pasek이 제시한 DC 모터의 모델링 방법에 의해 얻어진 모델을 포함하는 구동기 모델에서 속도제어기 부분을 제외한 모델을 대상으로 한다. 제안한 견실 속도제어기 설계방법은 파라미터 변화나 부하토크 변동 등의 외란에 대하여 폐루프 시스템의 견실안정성과 원하는 속도에 좋은 추적 성능을 보인다. 제어 대상인 포항제철 2열연공장의 열간압연 구동기에 대한 시뮬레이션을 통해 기준속도 추적성, 응답속도, 불확실성과 외란에 대한 견실성 등의 성능에 기존의 PI 속도제어기보다 양호함을 확인함으로써 제안한 견실 H/sup .inf./ 속도제어기 설계 방법의 타당성을 보인다.

• Proceedings of the KIEE Conference
• /
• 1986.07a
• /
• pp.128-131
• /
• 1986

• Proceedings of the KWS Conference
• /
• 1997.05a
• /
• pp.25-26
• /
• 1997