• The Korean Journal of Rheology
• /
• v.4 no.1
• /
• pp.46-51
• /
• 1992

본 연구에서는 열가소성고무를 중심으로 한 스티렌 공중합체의 유변학적 특성을 Couette 보정치를 사용하여 해석하였다. 실험재료로는 SBS(Styrene-Butadiene-Styrene), SEBS(Styrene-Ethylene/Buthylene-Styrene), SIS(Styrene-Isoprene-Styrene)을 사용하였고 탄성체의 성격을 비교하기 위하여SBS(Styrene-Butadiene Rubber)와 IR(Isoprene Rubber)를 사용하였다, 실험결과 Couette 보정치는 온도가 증가할수록 감소하였다. 또한 열가소성 고부 (SBS, SEBS, SIS)의 보정치는 거의 비슷한 값을 나타내었으며 고무(IR, SBR)의 보정치는 열가소성고무에서보다 다소 높은 값을 나타내었다. 충진제를 첨가하였을 경우 충진제의 양 이 증가할수록 Couette 보정치는 감소하였다.

• Proceedings of the Korean Fiber Society Conference
• /
• 1998.10a
• /
• pp.422-425
• /
• 1998

섬유강화 복합재료는 고성능 섬유와 고분자 수지를 조합하여 재료의 물성 향상 및 고기능화를 목적으로 만들어지는 재료이며, 사용되는 고분자 매트릭스의 종류에 따라 열가소성 복합재료와 열경화성 복합재료로 나뉘어진다. 이 중 열경화성 복합재료에 관한 연구 및 그의 실용화는 오래 전부터 활발히 진행되어 산업재료 및 군사, 우주용 재료로 각광을 받아 왔으나 최근 지구 환경문제가 심각해지면서 사용 후 분해 및 재활용이 가능한 열가소성 복합재료에 관한 연구에 관심을 가지게 되었다. (중략)

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.10
• /
• pp.127-134
• /
• 1997

열가소성 복합재료는 고상 성형법에 의해 저렴한 가격으로 부피가 튼 제품의 제조에 널리 사용될 수 있어 아주 좋은 전망을 가지고 있다. 그러나, 이러한 재료의 성형성에 대해선 아직 잘 알려지지 않았다. 본 연구의 첫번때 주안점은 2축 인장성형시 성형성에 대한 연구에 두었다. 실험에 사용된 재료는 임의의 방향으로 위치한 유리 섬유를 중량비로 20, 35, 40% 함유한 폴리프로필렌이다. 성형시험은 75 .deg. C 에서 150 .deg. C 사이의 온도에서 행했으며, 펀치 속도는 0.01cm/sec 와 1cm/sec 에서 행했다. 2축 인장성형에서 측정된 한계 변형률(Limiting Strain)은 Marciniak 불완전성 (Imperfection) 이론에 근거한 예견치외 비교되었다. 이론치와 실험치가 잘 일치함을 보였으며, 성형한계선도(Forming Limit Diagram) 로써 결과들을 요약하였다. 성형한계 변형률은 성형온도와 성형속도에 의해 크게 영향을 받는다는 것을 보인다. 이러한 결과들은 적절한 성형조건이 선택된다면 열가소성 복합재료의 인장성형은 실제 상업적으로 이용하기에 충분한 성형성을 갖는다는 것을 보인다.

• Composites Research
• /
• v.16 no.2
• /
• pp.33-40
• /
• 2003

In order to overcome one of the most pronounced shortcomings of conventional laminated composites, such as the low damage tolerance due to delamination, the thermoplastic materials and 3D (three-dimensional) preforms have been utilized in the manufacture of composite materials. From the newly developed process termed as the co-braiding, hybrid yarns of the thermoplastic fibers (PEEK) and reinforcing fibers (carbon) have been fabricated. In order to further enhance the delamination suppression, through thickness fibers have been introduced by way of 3D weaving technique in the fabrication of textile preforms. The preforms have been thermoformed to make composite materials. Complete impregnation of the PEEK into the carbon fiber bundles has been confirmed. For the comparison of mechanical performance of 3D woven composites, quasi-isotropic laminates using APC-2/AS4 tapes have been fabricated. Tensile and compressive properties of both the composites have been determined. Furthermore. the open hole, impact and CAI(Compression After Impact) tests were also carried out to assess the applicability of 3D woven textile reinforced thermoplastic composites in aerospace structures.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2007.11a
• /
• pp.150.1-150.1
• /
• 2007

• Proceedings of the Korean Fiber Society Conference
• /
• 1998.04a
• /
• pp.85-90
• /
• 1998

고무와 같은 유연성과 탄성을 가지면서 가유 필요없이 열가소성 성형기로 성형이 가능한 열가소성 탄성체는 1958년 E.I DuPont에 의해 폴리우레탄계 탄성섬유가 최초로 개발된 이래 낮은 생산원가와 대량생산이 쉬운 이점 때문에 많은 종류의 화합물이 개발되어 사용되고 있다.(중략)

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.5
• /
• pp.18-26
• /
• 2013

This study suggested techniques to reduce burning rate and their effects for the AP thermoplastic composite propellant. Burning rate obtained through ground tests using a small size motor were analyzed to investigate the effects of AP particle size and LiF of 0.5~2.0% on the inhibition reaction for the PEBAX/AP thermoplastic propellant. The results showed that utilization of large size particle of AP and addition of LiF under 2.0% can reduce the burning rate sufficiently and their quantitative effects were suggested in this paper.

• Composites Research
• /
• v.34 no.6
• /
• pp.421-425
• /
• 2021

In this study, thermoplastic composites were manufactured using a thermoplastic resin (PEEK) with the same melting temperature and a highly heat-resistant carbon UD tapes with different carbon fibers (Type A, Type B). And the bonding characteristics and mechanical characteristics of each of the two produced thermoplastic composites by induction heating welding were examined. The bonding characteristics and mechanical characteristics of the thermoplastic composites were performed using C-Scan and B-Scan, which is a non-destructive inspection, and the single lap shear test, respectively. The temperature of the carbon composites surface was monitored using a thermal image camera.

• Composites Research
• /
• v.29 no.5
• /
• pp.243-248
• /
• 2016

Although thermoset carbon fiber composite bipolar plates not only have high mechanical properties but also high corrosion resistance in acid environment, high manufacturing cost and low bulk electrical conductivity are the biggest obstacle to overcome. In this research, thermoplastic polymer is employed for the matrix of carbon composite bipolar plate to increase both the manufacturing productivity and bulk electric conductivity of the bipolar plate. In order to increase the electrical conductivity and strength, plain type carbon fabric rather than chopped or unidirectional fibers is used. Also nano particles are embedded in the thermoplastic matrix to increase the bulk resistance of the bipolar plate. The area specific resistance and the mechanical strength of the developed bipolar plate are measured with respect to the environmental temperature and stack compaction pressure.

• Composites Research
• /
• v.32 no.6
• /
• pp.360-367
• /
• 2019

In order to apply thermoplastic composites using PETG resin to various industrial fields such as bicycle frames and industrial parts, it is necessary to verify the impact resistance, durability, mechanical properties and 3D analysis of the manufactured composite materials. To improve the mechanical properties, durability and impact resistance of PETG resin, an amorphous resin, in this study, compound and injection molding process were carried out enhanced various weight percent POE(polyolefin elastomer). The thermal and mechanical properties of the thermoplastic composites, and the charpy impact strength, The analysis was performed to evaluate the characteristics according to weight percent of POE. Charpy impact strength test was conducted to analyze the impact characteristics, and the fracture section was analyzed after the impact strength test. In the case of POE material-added thermoplastic composites, thermal and mechanical properties tend to decrease, but workability and impact resistance tend to be superior to those of PETG materials.