• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.9
• /
• pp.569-576
• /
• 2016

The objective of this study was to investigate, using a numerical method, the fuel injection targeting for improving the combustion performance in a HSDI diesel engine. In this work, the ECFM-3Z model was applied as the combustion model, and the injection mass, inclined spray angle, and injection timing were varied for the study on the targeting of fuel spray. The results of this work were compared in terms of cylinder pressure, rate of heat release, and exhaust emissions characteristics. It was found that the cylinder pressure increased when the injection timing was advanced, and the rate of heat release increased when more fuel was injected into the piston bowl. In addition, $NO_x$ emission increased owing to the increase in the rate of heat release. On the other hand, CO and soot emissions decreased because of the improvement in combustion performance.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.6
• /
• pp.38-47
• /
• 2008

The liquid column and spray trajectory have been experimentally studied in liquid jets injected into subsonic crossflow. With water as fuel injection velocity, injection angle were varied to provide of jet operation conditions. The Pulsed Shadowgraph Photography and Planar Liquid Laser Induced Fluorescence technique was used to determine the injection characteristics in a subsonic crossflow of air. And the mainly objectives of this research was to get a empirical formula of liquid column and spray region trajectory with forward and reversed injection of air stream. As the result, This research has been shown that each trajectories were spatially dependent on air-stream velocity, fuel injection velocity, various injection angle, and normalized injector exit diameter. Furthermore, the empirical formula of liquid column trajectories has been some different of drag coefficient results between forward and reversed angled injection.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.300-303
• /
• 2010

This work shows the result of numerical simulation on a reacting flow by varying atomization properties which can be obtained from a injector for a small and low power aircraft gas turbine engine. Because the atomization properties mainly affect on the performance of the engine, a lot of efficiency tests are needed when a new injector is developed. Nowadays researches has been actively performed using computational analysis. Using commercial package CFD-ACE+, basic studies on the reacting flow field have been conducted. Those results show that the reaction rate is increased when higher pressure and wider angle spray condition are used. More smaller parcels can also enhance the fuel-air reaction.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.2
• /
• pp.166-174
• /
• 2009

The liquid column trajectory and column breakup length characteristics have been experimentally studied in angled jets injected into subsonic crossflow. Pulsed shadowgraph photography and Planar Liquid Laser Induced Fluorescence measurements were used to determine the angled effects. And the main objectives of this research are to get a empirical formula of liquid column trajectory and breakup length with below the $90^{\circ}$ degree injection angle conditions, and were compared with previous results. It was also found that the empirical formula, which reversed injection conditions of air stream. As the result, This has been shown that liquid column trajectories and column breakup length were spatially dependent on various injection angle, normalized injector exit diameter, air-stream and fuel injection velocity. Furthermore, the empirical formula of liquid column trajectories and breakup length has been some different of drag coefficient results between normal angled injection and reversed injection in subsonic crossflow.

• Journal of ILASS-Korea
• /
• v.23 no.1
• /
• pp.36-41
• /
• 2018

Fuel wall film effects power output and cycle deviation by changing the amount of fuel flowing into cylinder in PFI gasoline engines. Reduction of wall film can reduce fuel consumption and improve combustion stability. In this research, the effects of injection strategies including injection pressure and dual injection system is investigated for reducing wall film formation. The CONVERGE software is used for numerical analysis tool and O'Rourke film splash model was used for wall film prediction model. Compared with the reference case wall film decreased with increase of injection pressures, and the film formation reduced when the dual injection system was used.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.2
• /
• pp.221-229
• /
• 2015

The PFI dual injection engine using one injector per an intake port was developed for solving the DISI engine cost problem. Excellent fuel atomization and targeting of the PFI dual injection engine made enhancement on the fuel efficiency and engine power. In order to develop a PFI dual injection engine, characteristics of the in-cylinder flow and fuel behavior with respect to fuel injection angle and cone angle of the PFI dual injection engine was investigated. Numerical calculation was conducted to analyze 3D unsteady in-cylinder flow and fuel behavior using STAR-CD. The engine operating condition was 2,000rpm at WOT. As a result, the amount of intake air, evaporated fuel and fuel film according to injection angle and cone angle were presented. The results were influenced by interaction between injected fuel and intake port wall.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.353-355
• /
• 2008

최근 석탄 가스화 기술은 화석연료인 석탄을 기존의 공해물질 발생을 90%이상 줄이면서 고효율로 활용할 수 있는 방법으로 각광받고 있다. 본 연구는 습식 석탄 가스화기에서 가스화의 핵심적인 요소인 버너의 분무 관계 분야에 대한 분무 특성 및 무화성능을 높일 수 있는 분무기의 구조 및 운전 조건 등을 제시 할 목적으로 분무 시 내부를 관찰 할 수 있는 아크릴을 이용하여 내부 혼합식 버너를 제작하였다. 미립화 특성을 파악하기 위하여 $O_2$/Fuel Ratio 및 버너의 내부 혼합 방식, 분사각도, 각 분사 높이에 따른 미립화 특성을 관찰하였으며, 입도 분석은 심파텍사의 입도 분석기를 이용하여 측정하였다. 내부 혼합식 버너의 입도는 분사 각도와 $O_2$/Fuel Ratio에 따라서 변화하는 경향을 나타냈으며, 공급되어지는 Fuel은 석탄 슬러리와 물을 이용하여 각각의 입도를 측정하였다. slurry의 공급량이 고정된 상태에서 산소 공급량이 증가함에 따라 미립화도는 증가하는 경향을 나타내었으며, 슬러리 공급량과 산소 공급량이 동일한 경우 버너의 분사 각도에 따라 미립화도가 다르게 나타나는 특성을 관찰하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.4
• /
• pp.899-906
• /
• 1990

본 연구에서는 자동차엔진에 대한 응용의 일환으로써 밀폐된 축대칭 연소실내 의 정지하고 있는 공기에 분사에 의해 형성된 분무액적들을 점화원을 이용하여 화염을 생성시키고 그에 따른 화염전파 및 낮은 마하수에서의 유동현상과 이상간의 물리적 관 계를 다차원 유한차분법에 의한 물리적인 지배방정식의 동시해법인 ALE(Arbitrary La- ngrangian Eulerian)방법으로 구성되어 있는 CONCHAS-code를 이용하여 해석하고, 연료 액적의 분사각도, 크기 및 연소실내 기체유동의 각속도의 변화에 의한 분무연소의 과 도적특성을 고찰하고자 한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.74-77
• /
• 2011

A mixing characteristics on recess length change of Gas-centered swirl coaxial injector using high-performance staged combustion rocket engine carry out study through CFD(Computational fluid dynamics). propellant phase that combined gas-liquid simulate gas-gas. In order to measure spreading angle, velocity distribution to injector exit and spray structure of propellant analyzed. Axial velocity increase by increasing recess length, but tangential velocity decrease. The result confirmed qualitative characteristics that the spreading angle decreases.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.353-357
• /
• 2005

LOx post damage occurs from the development process of the full-scale gas generator which is necessary to 30 tonf class engine development was described. The cause and analysis for damage was described. The combustion test result of 4 injector, the full-scale gas generator and redesigned injector was described. Combustion instability, purge, the low momentum of LOx spray, small recess number, the low flow of LOx, and the high spray angle is main reason the possibility of knowing. The redesign for the injector in the direction of increase of recess number, increase of LOx and fuel spray angle, decrease of gap interval between the LOx post outer wall and fuel screen and increase of LOx post wall thick became accomplished.