• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.3
• /
• pp.59-66
• /
• 2010

Around a toll plaza, vehicles do such maneuvers as slow down, stop, and speed up to pay their tolls when they use ordinary toll gates. They can be expected more fuel consumptions compared to the vehicles which use the Hi-pass, a Korean type of Electronic Toll Collection System(ETCS). To measure the exact amount of difference between the two gas consumptions, we equipped a test vehicle with a measurement system and constructed a model toll gate on our test field. Through the field tests on fuel consumptions, we could confirm a 36.7 % of energy saving when the test car used the Hi-pass. Then we projected the result on the total traffic volumes which had used national expressway network for five months from January 2009. Projected to the whole traffic, potential cost savings reached 5.34 billion won. We expect this result be frequently mentioned of to prove the fuel efficiency of the Hi-pass system.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2007.05a
• /
• pp.131-132
• /
• 2007

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2007.11a
• /
• pp.241-242
• /
• 2007

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.10-19
• /
• 1990

본 기고에서는 농도분석에 사용되는 많은 측정장비 중에서 여러가지의 가스성분을 한번에 측정할 수 있고, 다른 전용가스분석기에 비하여 경제적인 가스크로마토그라프를 소개하고, 특히 탄화수소(hydrocarbon)계열의 연료를 사용하는 열기관의 배기가스분석에 국한하여, 적용예와 문제점을 검토하여 가장 최적의 가스크로마토그라프 운용조건을 찾는데 도움이 되고자 한다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2004.05a
• /
• pp.166.1-166.1
• /
• 2004

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.1
• /
• pp.26-31
• /
• 2011

In this study, it made to run conventional single direct injection(DI) diesel engine, which adapted bulk combustion system not following spark ignition system without any ignition apparatus. It was heated and controlled inlet-air into conventional single DI diesel engine. The maximum value of brake thermal efficiency was at 35 region of air-fuel ratio. On the contrary, when the region of air-fuel ratio leaner than 35, brake thermal efficiency was decreased suddenly. And brake thermal efficiency was increased as much as inlet-air heating temperature increased. So, when air-fuel ratio was decreased and inlet-air heating temperature was higher, the engine was in optimal operation condition.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.12 s.243
• /
• pp.1360-1368
• /
• 2005

This study investigates the characteristics of spray, such as evaporation rate and spray trajectory, for a 4-hole injector which is applied to a 4-valve motorcycle gasoline engine. Three dimensional, unsteady, compressible flow and spray within the intake-port and cylinder have been simulated using the VECTIS code. Spray characteristics were investigated at 6000 rpm engine speed. Furthermore, we visualized fuel behavior in the intake-port using a CCD camera synchronized with a stroboscope in order to compare with the analytical results. Boundary and intial conditions were employed by complete 1-D simulation of the engine using the WAVE code. Fuel was injected into the intake-port at two time intervals relative to the position of the intake valves so that the spray arrived when the valves were closed and fully open. The results showed that the trajectory of the spray was directed towards the lower wall of the port with injection against the closed valves. With open valve injection, a large portion of the fuel was lifted by the co-flowing air towards the upper half of the port and this was confirmed by simulation and visualization.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.9
• /
• pp.1736-1743
• /
• 1992

The combustion in the cylinder of spark ignition engine is completed after the delayed time that the liquid film fuel is vapourized as flowing into the combustion chamber. It is necessary to enhance the homogeneity of mixture and the combustion phenomenon in order to improve the heat efficiency and the emission characteristics of spark ignition engine. The main purpose of this paper is to manufacture a combustion analyzing system and examine closely the influence of non-uniformity due to the liquid film fuel flowing in the intake manifold on the combustion characteristics by using a 4 stroke multi- cylinder spark ignition engine. Moreover, with each cylinder, the interpretation of combustion characteristics by indicator diagram and the concentration of exhaust gas were investigated.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1019-1024
• /
• 2011

The gaseous fuel injection(GFI) type of LPG fuel-supply system is more advantageous than liquefied fuel injection(LFI) from the viewpoint of durability and cost reduction. However, compared with LFI types of LPG fuel-supply systems, in the GFI systems it is difficult to achieve precision fuel metering because of the compressible characteristic of the gaseous fuel. In this study, a Helmholtz resonator is proposed as an appropriate system for precision fuel metering in GFI systems, and the effects of the Helmholtz resonator on the fuel metering are simulated by the commercial flow-network-analysis package Flowmaster.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.16-22
• /
• 1987

직접분사식 디젤기관의 성능과 배기가스 문제에 여향을 주는 실린더 내에서의 연소형태는 크게 연료분사계와 흡입공기 유동계 두 가지에 의해 결정된다. 즉 분사율, 부사시기, 분무형태와 같은 분사계의 특성과 공기선회, 스퀴시(squish), 난류와 같은 공기 유동 특성에 의하여 연소형태가 결 정된다. 이러한 복잡한 연소형테를 기관 특성에 맞게 조정한다는 것은 대단히 어려운 문제인데 이것은 연료화 공기의 혼합이 연소실형상과 흡기계의 형상에 큰 영향을 받으며 연료가 액체 상 태로 연소실내로 들어와 분무과정을 통하여 증발이 되어야만 연소가 가능하기 때문이다. 특히 흡입공기 유동계에 있어서 현재의 직접 분사식 대젤기관의 흡입구 형상은 흡입공기의 운동에너 지에 모멘트를 가하여 연소실내에서 공기의 선희(swirl)를 발생시켜 줌으로써 연료와 공기의 혼 합기를 형성시키는 Helical type이 많이 이용되고 있다. 그러나 기관 성능과 배기가스 특히 NOx는 상반관계를 이루기 때문에 연소실내로 들어오는 흡입공기의 선희강도(swirl ratio)를 너무 강하게만 한다고 하여 좋은 결과를 얻을 수는 없다. 따라서 설계하고자 하는 각 기관에 있어서 요구되는 성능과 배기가스 문제를 만족하는 흡입공기의 선희강도가 얻어질 수 있도록 흡입구 형상을 설계한다는 것은 많은 연구와 경험이 요구되고 있다. 본 자료에서는 직접분사식 디젤기 관에 있어서 흡입공기의 최적 선희강도에 대한 설정방법과 흡입구 형상 설계를 위한 설계 이론 및 정상류 Rig test상에서의 흡입공기 선희강도의 평가방법을 소개하고자 한다.