• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.3
• /
• pp.115-124
• /
• 2003

In this study, the relationships between the displacement and stress of the tunnel using various analysis methods were compared with monitoring results carried out during construction and maintenance monitoring. The behavior of tunnel were measured in the subway tunnel passing comparative soft the weathering and analyzed both security and mechanical characteristics of the tunnel lining. With the results of simplified monitoring observed in top heading and bench excavation tunnel, it is confirmed that the crown settlement is larger than the surface settlement. it is interesting to note that the crown settlement and the crown shotcrete lining stress are widely used monitoring items for the back analysis. It is analyzed that the residual water pressure applied in the drainage type tunnel is reasonable.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.12
• /
• pp.1345-1350
• /
• 2014

This paper presented analysis methods for adapting E-glass fiber/epoxy composite (GFRP) materials to an automotive leaf spring. It focused on the static behaviors of the leaf spring due to the material composition and its fiber orientation. The material properties of the GFRP composite were directly measured based on the ASTM standard test. A reverse implementation was performed to obtain the complete set of in-situ fiber and matrix properties from the ply test results. Next, the spring rates of the composite leaf spring were examined according to the variation of material parameters such as the fiber angles and resin contents of the composite material. Finally, progressive failure analysis was conducted to identify the initial failure load by means of an elastic stress analysis and specific damage criteria. As a result, it was found that damage first occurred along the edge of the leaf spring owing to the shear stresses.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.3
• /
• pp.31-38
• /
• 2003

In the present work, a nonlinear inverse perturbation method which has been used in the structural optimization, is adopted so as to identify the structural damages. Unlike the structural optimization, a larger number of constrained equations than the number of unknown parameters are often required detect structural damage. Therefore, nonlinear least squares method is utilized to solve the problem. Because only a limited number of sensors are available I real situation of damage detection, the determination of sensor location becomes one of the most important issues. Hence, this work concentrates on the issue of sensor placement in the framework of nonlinear inverse perturbation method, and the performances of various methodologies concerning to sensor placement are compared with each other. The comparisons show tat the successive elimination method gets good performance for sensor placement. From the several numerical studies, it is confirmed that the inverse perturbation method, combined with the successive elimination method, is very promising in structural damage detection.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.24 no.4
• /
• pp.247-256
• /
• 2012

The purpose of this study is to decide the permeability and the rate of flow in a way of both site investigation and backward analysis and the most reasonable numerical analysis by performing a seepage model test for measuring the deformation swept volume of the embankment body in order to review a stability of the sea dyke being composed of multi-layers depending on variation of infiltration. As a result of the review, it could be forecasted that sweeping loss would be taken place at the boundary between bed protection works and embankment materials of the sea dyke due to a permeability difference of the multi-layered bed foundation structures and the sea dyke deformation would be occurred as a result thereby. As result of a numerical analysis for the seepage model test, it could be observed that critical velocity method was found to be smaller than the numerical analysis value but its tendency was similar and therefore it was judged that this method could be applied for the actual cross section.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.3
• /
• pp.5-13
• /
• 2003

The soil nailing is one of the useful support-system in urban excavation because of the presence of other structures in the vicinity Since the soil nailing system was introduced, model experiments and theoretical studies have been performed to investigate behavior of soil nailed wall. However, there are few data in the case of multi-layered soil strata just like Seoul Metropolitan area in Korea. The feed back analyses are carried out using the measured wall displacement data for soil nailing construction sites with multi-layered strata in order to analyze the distance and the coefficients of extension zone of ground behind soil nailed wall. As a result, the distance of extension zone increased with increasing of the final excavation depth and the ratio of the distance to the final excavation depth was shown to be about 94% of the final excavation depth. Also, the coefficients of extension zone increased with enlargement of soil layer thickness and converged into constant value of 1.05. On the other hand, the maximum vertical displacements by the feed back analysis and Caspe's method were shown to be approximately 80%, 150~280% of the maximum horizontal displacement respectively.

• Journal of the Society of Disaster Information
• /
• v.19 no.1
• /
• pp.31-43
• /
• 2023

Purpose: In this study, an analysis of the differences between the elastoplastic analysis and the numerical analysis and a study of the design ground constant recalculation method to derive similar trends in the analysis results were conducted. Method: The relational expression between the ground reaction force coefficient and the ground deformation coefficient at the time when the wall displacement becomes the same according to shallow excavation and deep excavation was derived. Result: Based on the measurement results, reverse analysis was performed to re-calculate the ground properties suitable for the site ground, and as a result of comparing and verifying the wall displacement using the derived formula and the literature formula, the proposed formula showed the most similar value. Conclusion: If the proposed formula is used, it will be helpful in practice because it is possible to infer the most similar ground properties to the actual at the time of design.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.1 no.2
• /
• pp.51-58
• /
• 2010

This work examines the identification of stiffness reduction in damaged reinforced concrete bridges under moving loads, and carries out the performance assessment after repairing using advanced composite materials. In particular, the change of stiffness in each element before and after repairing, based on the Microgenetic algorithm as an advanced inverse analysis, is described and discussed by using a modified bivariate Gaussian distribution function. The proposed method in the study is more feasible than the conventional element-based method from computation efficiency point of view. The validity of the technique is numerically verified using a set of dynamic data obtained from a simulation of the actual bridge modeled with a three-dimensional solid element. The numerical examples show that the proposed technique is a feasible and practical method which can inspect the complex distribution of deteriorated stiffness although there is a difference between actual bridge and numerical model as well as uncertain noise occurred in the measured data.

• Geotechnical Engineering
• /
• v.12 no.4
• /
• pp.131-144
• /
• 1996

In order to accelerate the rate of consolidation settlement and to gain a required shear strength for a given soft clay deposit, the preloadina technique combined with a vertical drainage system has been widely applied. Even if a sophisticated numerical analysis technique is applied to solve the consolidation behavior of drainage-installed soft deposits, the actual field behavior is often different from the behavior predicted in the design state due to several uncertainties involved in soil properties, numerical modelling, and measuring system. In this paper, two back-analysis schemes such hs simplex and BFGS methods have been implemented in an a Bisymmetric consolidation program, AXICON which considers the variation of compressibility and permeability during the consolidation process. Utilizing the program, one might be able to appropriately predict the subsequent consolidation behavior from the measured data in an early stage of consolidation of drainage-installed soft deposits.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.4
• /
• pp.415-429
• /
• 2013

Performance-based design is becoming a key word for structure design in architectural and civil engineering spheres. In this paper, the need of the performance-based design, especially for tunnels, was enhanced by case study on the largely deformed cut-and-cover arch tunnel built by the prescribed design. In addition, this paper introduces effective method of subdivision on tunnel performance to help field engineer's comprehension. Case study dealing with the issue of typical backwards problem in geotechnical engineering was examined. First of all, the outline of the damaged culvert as well as the surrounding embankment is in detail described. The background, together with the cause of damage, is discussed based on the results of site investigation. Secondly, it was attempted to elucidate the deformation mechanism of the embankment by means of numerical analysis, and the countermeasures are proposed. Finally, the stability of the embankment with the countermeasures was evaluated.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.5 s.57
• /
• pp.109-120
• /
• 2009

This paper introduces a new method to estimate the loss of prestressing force for the externally prestressing tendon. The proposed method that combines of HGA and FEM is able to identify the lost tensile force of a externally prestressed tendon. The identification variables of the proposed method is a exteranlly prestressed tendon of tension, effective nominal diameter, mass per unit length and Rayleigh damping coefficients. First of all, a finite element model system is constructed to consider the effect of damping, and these variables are identified using inverse analysis technique - updating algorithm. Finally, throughout total 3 cases of numerical tests, the numerical propriety of the proposed method is verified. Here, it is seen that the errors in the estimated variables by the proposed method are about 1% except in the case of Rayleigh damping coefficients.