• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.11a
• /
• pp.25-28
• /
• 2006

The contiguous construction in downtown area requires an appropriate substructure construction method since it results in the insufficient working spaces and frequent public resentment by noise and vibration. In particular, Top-down method usually is applied for downtown construction, and followed by several difficulties in casting the slab concrete for substructure. In this study, we focus on the improvement workability for substructure construction.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.229-230
• /
• 2019

Integrated water-soluble film is dissolved in the rubber asphalt waterproof sheet to secure adhesive strength on freshly cast concrete on the adhesion side of waterproofing layer on the floor slab. In addition, in order to determine whether the water in the concrete slurry can dissolve the water-soluble film sufficiently, the adhesive strength of the waterproofing sheet was compared between difference wetness condition at the upper part of the concrete specimen before the concrete casting.

• Journal of the Korea Institute of Building Construction
• /
• v.5 no.1 s.15
• /
• pp.105-109
• /
• 2005

Classified with concrete as placing ways - direct ways, sheath way - and placing directing flange direction, web direction - is analyzed section and strength of hardened concrete. The results of this study is belows the more fluid of concrete, the more useful to top-down method. To minimize the voids of the reverse placement joints, It is more effect to use the sheath method than direct method in concrete placement. If the joint face is a plane, it is impossible to extract the air bubbles which caused voids, so we should consider about this, and decide to select which type of joints.

• Journal of the Korean Geosynthetics Society
• /
• v.21 no.3
• /
• pp.49-59
• /
• 2022

This study was conducted to find out the rational and appropriate design of drilled shaft. In other words, in order to find out the variation of ultimate bearing capacity according to the change in the support layer of drilled shaft, back analysis was performed using the bi-directional pile load test performed on drilled shaft. Based on the back-analyzed data, numerical analysis of the pile head load was performed, and the ultimate bearing capacity in the target ground was evaluated using the Davisson method. As a result of numerical analysis of one case where the end of the pile was seated on the top of the weathered rock layer, and three cases where the end of the pile was embedded at different locations in the weathered soil, it was found that sufficient ultimate bearing capacity was secured in all cases. In other words, the case where the end of the pile is seated on the top of the weathered rock layer, not embedded the weathered rock, and the drilled shaft embedded into the weathered soil also have sufficient bearing capacity, so it can be used as a support layer for drilled shaft.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.1101-1106
• /
• 2000

When top down method is used, it could be a construction method trouble in column joint, between the former concrete and the latter. It could bring a void and weak concrete in column. The purpose of this study is to find a solution of removing void and air, way to exhaust air in top down column. through specimen concrete placing experiment.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.5
• /
• pp.97-105
• /
• 2001

현장타설말뚝의 건전도 평가에서 충격반향, 충격응답기법과 같은 비검측공 시험법을 적용하는 사례가 점차로 증가되는 추세에 있다. 비검측공시험법의 적용성을 체계적으로 평가하기 위해 수행된 일련의 연구결과 중에서 본 논문에서는 시험법의 결함탐지 능력을 평가하기 위해 수행된 해석적 연구결과에 관해 논한다. 이 연구에서는 시험법의 결함탐지능력에 대한 제반 영향인자 중에서 결함의 유형, 위치 및 크기의 영향을 평가하고자 하였다. 이를 위해서 여러 가지 조건에서 말뚝머리에 작용하는 충격하중에 대한 흙-말뚝 구조의 동적응답을 ABAQUS를 이용한 유한요소법으로 해석하였다. 이로부터 얻은 신호를 충격반향 혹은 충격응답기법으로 처리.분석하여 각 시험법의 결함탐지 능력을 평가해 보았다. 연구결과 이들 두 기법 모두 결함의 위치와 유형은 비교적 정확하게 탐지하는 것으로 나타났다. 그러나 충격응답기법을 이용하여 추정한 결함 크기는 신뢰도가 매우 낮았다. 이 문제를 해소하여 시험법의 적용성을 향상시키기 위해서는 측정된 동적응답신호를 이용하여 적절한 역계산 기법을 개발하여 적용할 필요가 있다는 결론을 얻었다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2001.11a
• /
• pp.34-39
• /
• 2001

When top down method is used, it could be a construction method trouble in column joint, between the former concrete and the latter. It could bring a void and weak concrete in column. The purpose of this study is finding a way to prevent concrete void and concrete suitable for top down, through V-metering for top down column and concrete experiment.

• Journal of the Korea Institute of Building Construction
• /
• v.1 no.2
• /
• pp.191-195
• /
• 2001

When top down method is used, it could be a construction method trouble in column joint, between the former concrete and the latter. It could bring a void and weak concrete in column. The purpose of this study is finding a way to prevent concrete void and concrete suitable for top down , through V-metering for top down column and concrete experiment. To minimize the void of reverse placement joint, It is more effect to use the sheath method then direct method in concrete placement.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.11a
• /
• pp.7-12
• /
• 2008

We constructed Seal type waterproofing with adhesive and swelling properties in the field of construction work as yet. But we have many problems of seal type waterproofing with adhesive and swelling properties for construction. Because it has high viscosity, so wokers are too adhered for the work. So, we developed and applied about the high temperature and spray equipments of piston type better than before. We able to be expect that cost reduction and increase construction ability by high temperature and spray equipments of piston type.

• Journal of the Korean Geotechnical Society
• /
• v.37 no.11
• /
• pp.7-22
• /
• 2021

In this study, inverse analysis was performed on the bi-directional axial compressive load test conducted on drilled shafts. And the bearing capacities were analyzed by numerical analysis of various pile tip ground conditions of silt clay, silt sand, sand silt, sand gravel, weathered rock, and soft rock. The bearing capacities were analyzed using the P-S method, the Davisson method, and the allowable sttlement of 25.4 mm. The minimum allowable bearing capacities analyzed by three methods were found to be 19.64 MN ~ 24.96 MN. At this time, the base resistances were sharing a 2% ~ 12% of a head load, shaft resistance were shared 88% ~ 98% of the head load. The greater the strength of pile tip was found to increase the allowable bearing capacity. However, the difference between the maximum allowable bearing capacity and the minimum allowable bearing capacity was 5.32 MN, and the increase in the allowable bearing capacity was only 27% depending on the pile tip.