• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.45-48
• /
• 2000

By the use of he DSP and microprocessor controller many high power converter such as especially inverter and motor drive system may be enhanced resulting in the improved robustness of EMI the ability to communicate the operating conditions and the ease of adjusting the control parameters. However the digital controller using DSP or microprocessor has not been applied in the high frequency switching power supplies especially in full bridge dc/dc converters. this paper presents a promising solution to the dc bias control problem of high frequency transformer in high power full bridge converter.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.565-567
• /
• 2008

가스터빈용 자동전압조정기는 발전기 출력 전압을 측정하여 발전기 단자 전압과 계자 전류를 제어하며, 발전기 여자시스템 보호/제한 기능을 수행한다. 본 논문에서는 전력연구원이 개발한 가스터빈 자동전압조정기의 시작품에 대한 소프트웨어와 하드웨어에 설계 및 제주화력 가스터빈에 현장 적용한 결과를 상세히 기술하였다.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.449-450
• /
• 2008

It is difficult to find for analysis solution of the synchronous generator exciter system. Recently, it had good performence UPS converter system using CRA method. The single converter of synchronous generator excitor system under considerations : (i) the overall system shall keep very low AC-voltage tracking error as well as no phase delay over different load condition, and (ii) the digital controller shall be employed at a fixed sampling. It is shown that the synchronous exciter system can be achieved by the proposed controller using Characteristic Ratio Assignment.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.268-271
• /
• 2001

This paper describes the power factor control of doubly fed induction machine using fuzzy logic algorithm in wind power generation system. Under fuzzy logic control, which enables superior dynamic performance, the power factor is independently controllable by decoupled d, q rotor experimental results are presented.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.959-962
• /
• 2005

Servomotors are used as key components of automated system by performing accurate positioning, accurate speed regulation, and precise motion control in response to commands from computers and sensors. Especially linear brushless servomotors have numerous advantages over ball screws, timing belts, rack/pinion drives and friction drives compared with rotary servomotors. This paper proposes the estimation of unknown parameters from the linear brushless DC motor which is operated by sinusoidal commutation. The estimated parameters are used to tune the controller gain and disturbance observer. In order to agree with this purpose, Digital Signal Processor(TMS320F240), developed for implementation of a speed Field Oriented Control(FOC), adopted in this study. The processor playing an important role in controller has A/D converters, PWM generators, riched I/O port internally.

• Proceedings of the KIPE Conference
• /
• 2016.11a
• /
• pp.186-187
• /
• 2016

본 논문에서는 권선형 유도기 기반의 엔진 발전기를 이용한 비상 전원 장치를 제안한다. 기존의 외부 여자동기 전동기를 이용한 엔진 발전기 시스템과 다르게 권선형 유도 전동기를 사용하여, 고정자 권선은 계통에 직접 연결되고, 회전자 단에는 배터리를 전력원으로 하는 인버터를 연결한다. 권선형 유도기가 엔진과 결합되어 엔진 발전기로 연결된 상태에서 계통사고로 계통이 단락 되는 경우 회전자 단 인버터를 이용하여 중요 부하에 전력을 공급하는 동시에 전동기를 구동시켜 엔진 발전기 동작 영역까지 전동기를 구동시키는 제어 방법을 제안한다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.3
• /
• pp.66-74
• /
• 2005

This paper presents an implementation of digital servo speed control system of SPMSM(Surface-mounted Permanent Magnet Synchronous Motor) for industrial application with Direct Torque Control(DTC) using TMS320F2812 DSP. Although, the vector control scheme is adapted in many industrial servo system, but the DSP calculation ratio is increased by reference frame transformation and SVPWM of vector control. Therefore, this paper investigate the possibility of DTC scheme for industrial servo drive system instead of vector control scheme. DSP calculation ratio is compared between vector control and DTC algorithm in addition to the characteristic of speed control response. The suggested SPMSM control system shows the possibility of DTC scheme for industrial servo motor drive system instead of a vector control algorithm.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.364-367
• /
• 1996

This paper deals with the design and evaluation of the robust controller for generator excitation system to improve the steady state and transient stabilities. The nonlinear characteristics of the system is treated as model uncertainties, and then the robust control techniques are introduced into the PSS design to take into account these uncertainties at the controller design stage. The performance of the designed controller is examined by extensive non-linear time domain simulation. It is shown that the performance of the robust controller is superior to that of the conventional PSS in all cases studied.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.375-378
• /
• 1991

This paper presents a design method of synchronous generator excitation controller using self-tuning PID algorithm. Controller parameter is determined by using adaptive control theory in order to maintain optimal operation of generator under the various operating conditions. To determine the optimal parameter of controller. minimum variance algorithm using the recursive leastsquare(RLS) indentification method is adopted and the difference between the speed deviation with weighted factor and voltage deviation is used as the input signal of adaptive controller, which provides good damping and conversion characteristics. The results tested on a single machine infinite bus system verify that the proposed controller has better dynamic performances than conventional controller.

• Proceedings of the KIEE Conference
• /
• 1999.07c
• /
• pp.1173-1176
• /
• 1999

전력계통에서 발생하는 저주파 동요에 대해서 가장 효과적인 제동력 향상방안으로 알려진 PSS의 최적 설치지점을 결정하기 위하여 NSE(Normalizing Speed Eigenvectors), SPF(Speed Participation Factors), TFR(Transfer Function Residues) 및 주파수 응답법을 각각 비교분석 하였다. 분석결과 SPF는 제어/입력 행렬을 포함하지 않는 상태행렬만을 고려하기 때문에 PSS의 제어특성을 반영하지 못하는 단점이 있었으며 TFR은 여자기 이득에 민감하여 최적위치 선정에 있어서 문제점을 보였다. 본 연구에서는 SPF법을 이용하여 PSS 설치 후보지를 선정하고 이들 후보지에 대해서 TFR법과 주파수 응답법으로 최적의 발전기를 결정하도록 하였으며 PSS를 설치하여 그 효과를 검증하였다.