• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1998.05a
• /
• pp.221-228
• /
• 1998

2차원 노심핵설계 코드 HELIOS를 이용하여 $^{7}$ LiF-BeF$_2$-ThF$_4$-$^{233}$ UF$_4$ 용융염 핵연료와 흑연(Graphite) 감속재로 구성된 AMBIDEXTER(Advanced Molten-salt Break-even Inherently-safe Dual-mission EXperimental and TEst Reactor) 원자로의 육각주형 로심격자에 대해 핵적 자활성 요건의 설계해석을 수행하였다. AMBIDEXTER 원자로는 액체 핵연료의 유동성을 이용한 온라인 핵연료 정화ㆍ처리ㆍ재생의 연속공정을 도입하여 노내의 잔류 핵분열 생성물질의 포화양을 최소로 유지시키고 중성자 경제성을 극대화하므로 높은 전환율을 얻는 설계이다. 핵연료 내에 잔류하는 핵분열생성물질의 포화농도에 대응하는 연소도를 등가연소도로 정의할 때, 열출력 250MW$_{th}$ AMBIDEXTER 원자로의 등가연소도 374MWD/TeH.E.의 평형 로심 모델에 대해 핵적 자활성을 지배하는 주요 핵설계 인자로서 용융염 핵연료의 $^{233}$ U Mole 분율, 흑연-대-용융염의 체적비, 노심격자 간격 및 출력 밀도의 변화에 따른 임계도 및 전환율을 평가하였다. 그 결과, $^{233}$ U Mole 분율과 혹연-대-용융염 체적비를 좌표축으로 하는 2차원상공간에서 핵적 자활성 요건 상태함수는 각 노심격자간격에 대해 완만한 선형 함수로 표현할 수 있음을 확인하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.196-200
• /
• 2005

In this work, we investigated simple Aㅣ/TCO/a-Si:H(n)/c-Si(p)/Al hetero-junction solar cells prepared by low temperature processes, unlike conventional thermal diffused c-Si solar cells. a-Si:H/c-Si hetero-junction solar cells are processed by low temperature deposition of n-type hydrogenated amorphous silicon (a-Si:H) films by plasma-enhanced chemical vapor deposition on textured and flat p-type silicon substrate. A detailed investigation was carried out to acquire optimization and compatibility of amorphous layer, TCO (ZnO:Al) layer depositions by changing the plasma process parameters. As front TCO and back contact, ZnO:Al and AI were deposited by rf magnetron sputtering and e-beam evaporation, respectively. The photovoltaic conversion efficiency under AMI.5 and the quantum efficiency on $1cm^2$ sample have been reported. An efficiency of $12.5\%$ is achieved on hetero-structure solar cells based on p-type crystalline silicon.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.483-486
• /
• 2008

본 연구에서는 디스크 이동식 열분해 실증 설비를 이용하여 폐타이어 열분해 반응을 수행하였고, 생성된 열분해 생성물들의 특성을 분석하였다. 폐타이어 열분해 반응은 약 $550^{\circ}C$에서 90분간 진행되었고, 반응 결과 Recovered Oil, Carbon Black, Non Condensing Gas(NC Gas)가 생성되었다. 폐타이어 열분해 생성물의 수율은 Recovered Oil $40{\sim}50%$, Carbon Black 30$\sim$35%, NC Gas 10$\sim$15%, Steel 10$\sim$15%로 나타났다. 폐타이어 열분해 반응 후 생성된 Recovered Oil은 비점 및 특성 분석 결과 상업용 중유와 비슷한 성질을 나타냈고, 폐타이어 열분해 반응의 또 다른 생성물인 Carbon Black은 특성 분석 결과 고정 탄소 비율이 낮은 반면 회분과 휘발분의 비율이 높아 상업용으로 사용하기 위해서는 적절한 정제 과정이 필요함을 알 수 있었다.열분해 과정 중에 생성된NC Gas는 GC/MS를 이용하여 성분 분석을 수행한 결과, $CO_2$, $CH_4$를 비롯하여 주로 탄화수소류로 이루어졌으며, 대부분이 연료 가스로 구성되어 있어 열분해 반응의 열원으로서 사용이 가능하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.390-393
• /
• 2008

To improve the blue responses of screen-printed single crystalline silicon solar cells, we investigated an emitter etch-back technique to obtain high emitter sheet resistances, where the defective dead layer on the emitter surface was etched and became thinner as the etch-back time increased, resulting in the monotonous increase of short circuit current and open circuit voltage. We found that an optimal etch-back time should be determined to achieve the maximal performance enhancement because of fill factor decrease due to a series resistance increment mainly affected by contact and lateral resistance in this case. To elucidate the reason for the fill factor decrease, we studied the resistance analysis by potential mapping to determine the contact and the lateral series resistance. As a result, we found that the fill factor decrease was attributed to the relatively fast increase of contact resistance due to the dead layer thinning down with the lowest contact resistivity when the emitter was contacted with screen-printed silver electrode.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.554-557
• /
• 2008

In this study, two types of central flow distributor designs are presented and compared to obtain the optimal compact design which has the least flow resistance and the uniform flow distribution in a vehicular fuel cell stack. For effective and reliable prediction on the thermo-flow characteristics of the reactants flow over the entire fuel cell stack domain, open channel flow in the bipolar plates of the power generating cells were simulated by applying a simplified flow resistance model with an empirical porous concept. A number of case studies were performed to figure out an optimal configuration of a central flow distributor device in terms of the time-dependent thermo-flow behavior and load-dependent flow distribution. The results showed that the stable and load-independent thermo-flow uniformity is very design specific, which is closely associated with the design of central manifolding devices in order to achieve the enhanced volumetric power density and the reliable long-lasting operating of fuel cells.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.247-252
• /
• 2008

This paper presents an active vibration control of cantilever beams under disturbances by a primary force. A direct velocity feedback control using a pair of PZT actuator and a velocity sensor is considered. Variation of the stability and performance with the locations of the sensor/actuator pair is investigated. It is found that the maximum gain varies with the locations of the sensor/actuator pair significantly. The maximum gain shows a symmetric distribution along the beam length with respect to the center point, although the boundary condition of the beam is unsymmetric. The control performance is affected by the location of the primary force as well as the location of the sensor/actuator pair. The active control system can more effectively reduce the vibration when the primary force is located close to the fixed boundary.

• Journal of Energy Engineering
• /
• v.12 no.1
• /
• pp.23-28
• /
• 2003

In this paper, in-air and in-water vibration characteristics of Rotary Specimen Rack (RSR) are estimated through 3D finite element modeling by using ANSYS software. Added mass is calculated by using Blevins' equation. To confirm the reasonability of the results presented in this study, obtained results are compared to those of using a theoretical equation. It is confirmed that in-water natural frequencies of the RSR are lower than in-air ones due to the added mass effect of the fluid. Also, to design clamp which needs to fix RSR, Von-Mises stress and displacement of RSR to clamp pressure are calculated.

• Journal of Energy Engineering
• /
• v.15 no.1 s.45
• /
• pp.28-34
• /
• 2006

The convective heat transfer on the outer surface of tube arrays perpendicular to the flow direction was experimentally investigated. The test sections which include the aligned and staggered arrangements were made and the local heat transfer coefficients on the outer surface of the tube were measured after the Hour has been fully developed. The results showed that the local heat transfer coefficients of the staggered arrangement, which has transverse pitch of 0.075 m and longitudinal pitch of 0.08 m, were about 15% greater than that of the aligned arrangement. Also, the overall mom Nusselt number of the former was greater thu that of the latter.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.648-654
• /
• 2005

The performance prediction of a planar-type solid oxide fuel ceil is conducted by a computational analysis. The transport processes are formulated with the help of a simplified treatment of heat generation by the electrochemical reaction. From the result of the computational analysis, it is shown that the electrochemical reaction is closely related to the transport phenomena inside a solid oxide fuel cell. Transport phenomena including heat and mass transfer have influence on the distribution of local current density and as a result, on the performance characteristics of the fuel cell. Computational analysis is also extended to the parametric study to investigate the performance behavior of the fuel cell with different amount of supplied fuel flow rates. It is also demonstrated that the mathematical formulation and computational procedures proposed in this study can be applied to prove the importance of the specific TPB(Three-Phase-Boundary) area in the manufacturing process of electrodes in a solid oxide fuel cell.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.1046-1049
• /
• 2009

최근 화석에너지 고갈 문제와 폐기물의 지속적인 발생량 증가로 인해 폐기물을 이용한 열에너지 회수가 이슈화 되고 있다. 폐기물처리를 통한 에너지 회수 공정 가운데 소각이 가장 많이 이용되고 있으나 소각시 발생하는 대기오염 물질을 처리하기 위한 설계 및 설치비용에 많이 소요 된다. 본 연구에서는 화학공정 모사기인 Aspen plus를 이용해 소각공정 및 배가스 처리 공정모사를 실시하였다. 폐기물 소각 공정으로는 1 2차 연소실과 NO2를 환원하는 SNCR공정, 산성가스(HCl, SO2)를 제거하는 SDA공정, 입자상 물질을 처리 하는 bag filter공정을 모사하였다. 공정모사 결과 실제 산업폐기물 소각로의 처리효율과 일치 하였고 이를 바탕으로 동일한 공정 및 조건하에 소각로에 투입되는 폐기물의 조성비를 달리하여 공정 모사한 결과 오염물질의 배출량을 예측할 수 있었다. 이러한 오염물질 발생량 예측은 소각장의 폐기물 투입이 일정하지 않을 경우 조업 조건의 변경에 도움 뿐만아니라 공정개선의 효과적일 것으로 판단된다.