• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.3
• /
• pp.1037-1047
• /
• 2013

A systematic laboratory compaction testing was performed with the laboratory seismic measurements of the compacted specimens sampled from various compaction fills and was supplemented with in-situ seismic testing to investigate the effects of compaction energy on the elastic wave velocities of the railway roadbed materials. The both variances of the compressive and shear wave velocities with moisture content curve ($V_p$-w and $V_s$-w curves) are similar to the general trend of the density-moisture content curve(${\gamma}_d$-w curve). At the wet side of optimal moisture content (OMC), either $V_p$ or $V_s$ does not significantly increase, which is well reflecting the no gaining in density with the increasing compaction energy exceeding modified-D compaction effort. $V_p$ increases linearly with ${\gamma}_d$ at the dry side of OMC, while it does exponentially at the wet side. The in-situ wave velocities were found to be influenced by the level of confinement and $V_s$ was more sensitive to compaction energy than $V_p$.

• Journal of Radiation Protection and Research
• /
• v.26 no.1
• /
• pp.7-12
• /
• 2001

Sintered LiF:Mg,Cu,Na,Si thermoluminescence (TL) pellets were developed for application in radiation dosimetry. In the present study, the TL dosimetric properties of LiF:Mg,Cu,Na,Si TL pellets have been investigated for emission spectrum, dose response, energy response, and fading characteristics. LiF:Mg,Cu,Na,Si TL pellets were made by using a sintering process, that is, pressing and heat treatment from TL powders. Photon irradiations for the experiments were carried out using X-ray beams and a $^{137}Cs$ gamma source at the Korea Atomic Energy Research Institute (KAERI). The average energies and the dose were in the range of 20-662 keV and $10^{-6}-10^{-2}\;Gy$, respectively. The glow curves were measured with a manual type TLD reader(System 310, Teledyne) at a constant nitrogen flux and a linear heating rate. For a constant heating rate of $5^{\circ}C\;s^{-1}$, the main dosimetric peak of glow curve appeared at $234^{\circ}C$, the activation energy was 2.34 eV and frequency factor was $1.00{\times}10^{23}$. TL emission spectrum is appeared at the blue region centered at 410 nm. A linearity of photon dose response was maintained up to 100 Gy. The photon energy responses relative to $^{137}Cs$ response were within ${\pm}20%$ at overall photon energy region. The fading of TL sensitivity of the pellets stored at the room temperature was not found for one year.

• Journal of Korea Society of Industrial Information Systems
• /
• v.23 no.1
• /
• pp.1-12
• /
• 2018

This paper presents a material estimation method using dual-energy X-ray images generated as a result of cargo inspection system in MeV region. We use new discrimination curve using logarithmic function rather than four discrimination curves commonly used in existing estimation algorithms. We also propose an atomic number estimation using the probability distribution of the logarithmic curve rather than linear interpolation. When the probability distribution is used as a weight, we used two methods of using the weight for the two nearest reference materials and the weight for all the reference materials. Experimental results showed that the atomic number estimation of materials using the probability distribution as a weight is more accurate than the existing methods. In order to visualize the estimated atomic number, the HSI model was used for color the resulting image.

• Journal of Energy Engineering
• /
• v.16 no.1 s.49
• /
• pp.22-31
• /
• 2007

This paper addresses methodology in order to consider CHP (Combined Heat and Power) capacity in the Basic Plan of Long Term Electricity Supply & Demand and presents effects on it. The method performs state in extent that do not change maximum in the Basic Plan of Long Term Electricity Supply & Demand. For analysis that occurs some advantage this method compares with Basic Plan of Long Term Electricity Supply & Demand. It includes EES (Expected Energy Served), Fuel consumption, amount of $CO_{2}$ emission reduction.

• Journal of Biomedical Engineering Research
• /
• v.20 no.5
• /
• pp.545-557
• /
• 1999

본 논문에서는 호흡 연동 장치와 EBT로부터 획득한 폐실질 영상에 대하여 동적 윤곽선 모델 방법과 영역 성장법을 이용하여 폐실질 영역을 검출하였다. 그런 다음 , 검출된 폐실질 영역내에서의 각종 정량적 요소들을 도출하여 농도 분포 곡선에대한 분석을 하였다. 동적 윤곽선 모델방법에서 페실질 영역의 낮은 휘도 준위와 폐의 윤곽선 벡터 방향을 고려한 에너지 함수를 제안하였다. 그리고 폐실질 영역 성장법에서는 폐실질 영역내의 분포한 공기 성분에 대한 화소를 확장시켜 효과적으로 폐실질 영역을 검출하였다. 추출된 폐실질 영역내의 빈도 분포 곡선을 분석하여 정상군과 비교한 결과 만성 폐쇄성 폐질환자에서는 정상인에 비하여 평균 농도,최대 빈도 농도, 최대 상승 기울기 농도가 낮았으며, 농도 분포곡선은 더 낮은 쪽으로 이동하였음을 알 수 있었다. 또한, 특발성 폐섬유증 환자에서는 평균 농도, 최대 빈도 농도, 최대 상승 기울기 농도가 모두 증가되었고 농도 분포 곡선은 더 높은쪽으로 이동하였다. 폐실질 영역을 추출하여 히스토그램 분포에 대한 정량적 분석을 함으로써 정상인으로부터 만성 폐쇄성 질환자의 폐섬유증 환자를 구분할 수 있었다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.667-670
• /
• 2009

본 연구에서는 MicroTec을 이용하여 태양전지의 IV특성곡선을 분석하였다. 태양전지의 IV특성곡선은 태양전지의 효율을 나타낸다. 효율을 높이기 위하여 전극이 직접 접촉하는 부분에 고농도의 형태를 취하고 나머지 전극이 없는 부분에 저농도 도핑으로 전면을 처리한다. 이때 고농도 층을 과대하게 불순물을 주입할 경우 전극부분의 재결합률이 상승하여 에너지 변환 손실로 이어진다. 본 연구에서는 태양전지의 최대효율을 얻을 수 있는 도핑의 농도를 결정하여 이의 IV특성곡선을 비교 분석 하고자한다.

• Journal of the Korean Magnetics Society
• /
• v.6 no.1
• /
• pp.1-6
• /
• 1996

To simulate the characteristics of magnetic exchange coupling at the interface of MR/TbCo thin films, the directions of magnetizations were calculated by minimizing energy in the films. Newton method and Gauss-Seidel method were used. The width of M-H curve increased with TbCo anisotropy constant, and with the thickness of the transition region of TbCo layer. Hysteresis loop width became extremely narrow (less than 10 Oe of coercivity), when the TbCo transition region length was $400\;\AA$. Also the hysteresis loop of films with low interfacial exchange coupling constant was similiar to that of short transition region length. When interfacial exchange coupling constant was 1/100 of perfect coupling, hysteresis loop showed a coercivity of less than 10 Oe. Comparing the measured hysteresis loop of a fabricated sample with that of simulated one, exchange coupling con¬stant could be estimated.

• Elastomers and Composites
• /
• v.39 no.1
• /
• pp.23-35
• /
• 2004

In this work, effects of hyper-elastic rubber material properties on the indentation load-deflection curve and subindenter deformation are first examined via finite element (FE) analyses. An optimal data acquisition spot is selected, which features maximum strain energy density and negligible frictional effect. We then contrive two normalized functions, which map an indentation load vs. deflection curve into a strain energy density vs. first invariant curve. From the strain energy density vs. first invariant curve, we can extract the rubber material properties. This new spherical indentation approach produces the rubber material properties in a manner more effective than the common uniaxial tensile/compression tests. The indentation approach successfully measures the rubber material properties and the corresponding nominal stress-strain curve.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.482-484
• /
• 2007

철도차량이 운행될 때 회생제동 구간에서는 회생에너지가 발생한다. 1500[V] DC급전시스템에서 회생된 에너지는 가선 전압을 상승시킨다. 상승된 가선전압은 급전시스템에 악영향을 주기 때문에 회생에너지를 활용하는 방법을 이용하여 가선전압을 안정화 한다. 회생에너지 활용방법의 하나인 회생에너지 저장 시스템을 적용할 때 고려해야 될 사항은 회생에너지의 발생양이다. 회생에너지의 양이 적어 활용가치가 떨어지는 구간에서는 적용하지 않기 때문에 회생량에 대한 사전 정보가 필요하다. 회생에너지의 양은 실측을 통해 얻을 수 있지만 측정을 위한 시간이나 고가의 장비를 사용해야하는 단점이 있다. 본 논문에서는 회생에너지 예측이 가능한 직류지하철 시스템의 모델링을 통해 실측시 발생하는 시간 및 비용적인 문제점을 해결할 수 있다. 회생에너지의 예측은 시뮬레이터를 이용하여 구배 및 곡선, 차량 데이터 등의 운전특성을 바탕으로 이루어진다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.83-83
• /
• 2005