• The Journal of Engineering Geology
• /
• v.33 no.1
• /
• pp.151-167
• /
• 2023

This study compares the revised method in loose saturated sandy ground where the LNG storage tank will be installed with an evaluation method by one-dimensional effective stress analysis using the UBC3D-PLM model. Various laboratory and field tests were conducted to establish the parameters necessary for evaluation. The revised liquefaction evaluation method using the seismic response analysis result and N value from standard penetration testing evaluated the possibility of liquefaction as high, but assessment using effective stress analysis, which can consider various liquefaction resistance factors, found the site to be somewhat stable against liquefaction. One-dimensional finite element analysis using UBC3D-PLM modeling facilitated easier assessment of stability against liquefaction than the other methods and minimized the area required for reinforcement against liquefaction. In addition, it is expected that two-and three-dimensional numerical analysis considering the foundation of the LNG storage tank can identify the seismic design and behavior when liquefaction occurs.

• The Journal of Engineering Geology
• /
• v.30 no.4
• /
• pp.589-602
• /
• 2020

As can be seen in many earthquakes, liquefaction causes differential settlement, which sometimes produces serious damages such as building destruction and ground subsidence. There are many possible active faults near the Busan city and the Yangsan, Dongrae, and Ilgwang faults among them pass through the city. The Busan city is also located within the influence of recent earthquakes, which occurred in the Gyeongju, Pohang, and Kumamoto (Japan). Along the wide fault valleys in the city, the Quaternary unconsolidated alluvial sediments are thickly accumulated, and the reclaimed lands with beach sediments are widely distributed in the coastal area. A large earthquake near or in the Busan city is thus expected to cause major damage due to liquefaction in urban areas. This study conducted an assessment of the liquefaction hazard according to seismic recurrence intervals across the Busan city. As a result, although there are slight differences in degree depending on seismic recurrence intervals, it is predicted that the liquefaction potential is very high in the areas of the Nakdonggang Estuary, Busan Bay, Suyeong Bay, and Songjeong Station. In addition, it is shown that the shorter the seismic recurrence interval, the greater difference the liquefaction potential depending on site periods.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.6
• /
• pp.307-317
• /
• 1999

The purpose of this study is to utilize conventional procedures for evaluation of liquefaction potential and to compare the results obtained by modified detailed method based on Korean earthquake magnitude (M=6.5). Liquefaction potential is assessed by comparing liquefaction strength of soil and cyclic shear stress generated in the soil layers during earthquakes. The cyclic shear stress is computed from the earthquake response analysis, and liquefaction strength of soil is evaluated by using results from cyclic triaxial tests. The cyclic triaxial tests are performed on many different conditions of sample ; relative densities(50%, 60%, and 70%), initial effective confining pressures (70kPa, 100kPa, and 150kPa), and fine contents(10%, 20%, and 30%). From the result of comparing the conventional procedure with the modified detailed method, it is found that the modified detailed method tends to evaluate larger safety factor against liquefaction in the weak sand site$(FS \leq1.5)$. Therefore in this case, it is suggested that liquefaction potential should be evaluated by using the modified detailed method based on cyclic triaxial tests. It is also found that in modified detailed method based on earthquake magnitude 6.5, critical depth where liquefaction can be generated is around 15m from the ground surface.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.1
• /
• pp.20-35
• /
• 2017

In the case of the seabed around and under gravity structures such as submerged breakwater is exposed to a large wave action long period, the excess pore pressure will be significantly generated due to pore volume change associated with rearrangement soil grains. This effect will lead a seabed liquefaction around and under structures as a result of the decrease in the effective stress, and eventually the possibility of structure failure will be increased. The study of liquefaction potential for regular waves had already done, and this study considered for irregular waves with the same numerical analysis method used for regular waves. Under the condition of the irregular wave field, the time and spatial series of the deformation of submerged breakwater, the pore water pressure (oscillatory and residual components) and pore water pressure ratio in the seabed were estimated and their results were compared with those of the regular wave field to evaluate the liquefaction potential on the seabed quantitatively. Although present results are based on a limited number of numerical simulations, one of the study's most important findings is that a safer design can be obtained when analyzing case with a regular wave condition corresponding to a significant wave of the irregular wave.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.2
• /
• pp.146-152
• /
• 2018

In the construction sector, new demands for aesthetics are increasing due to structural stability and improvement of living standard and consciousness level. On the other hand, Red Mud sludge is generated from aluminum hydroxide extraction process from Bauxite. Red mud sludge contains about 20% of $Fe_2O_3$ and represents a natural reddish brown. It is highly applicable to the construction industry. In this paper, red mud sludge with a water content of 50%, which is a by - product of the industry, was prepared as a liquid phase. The liquefied red mud was added to cement mortar and the strength and color difference of cement mortar were investigated according to the addition amount of liquefied red mud. As a result, the compressive strength decreased with increasing amount of liquefied red mud. The color of cement mortar containing liquefied red mud was found to be distributed in the range of YR series in all samples. As the amount of liquefied red mud increased, the color became darker.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.3
• /
• pp.174-183
• /
• 2014

Seabed beneath and near coastal structures may undergo large excess pore water pressure composed of oscillatory and residual components in the case of long durations of high wave loading. This excess pore water pressure may reduce effective stress and, consequently, the seabed may liquefy. If liquefaction occurs in the seabed, the structure may sink, overturn, and eventually increase the failure potential. In this study, to evaluate the liquefaction potential on the seabed, numerical analysis was conducted using the expanded 2-dimensional numerical wave tank to account for an irregular wave field. In the condition of an irregular wave field, the dynamic wave pressure and water flow velocity acting on the seabed and the surface boundary of the composite breakwater structure were estimated. Simulation results were used as input data in a finite element computer program for elastoplastic seabed response. Simulations evaluated the time and spatial variations in excess pore water pressure, effective stress, and liquefaction potential in the seabed. Additionally, the deformation of the seabed and the displacement of the structure as a function of time were quantitatively evaluated. From the results of the analysis, the liquefaction potential at the seabed in front and rear of the composite breakwater was identified. Since the liquefied seabed particles have no resistance to force, scour potential could increase on the seabed. In addition, the strength decrease of the seabed due to the liquefaction can increase the structural motion and significantly influence the stability of the composite breakwater. Due to limitations of allowable paper length, the studied results were divided into two portions; (I) focusing on the dynamic response of structure, acceleration, deformation of seabed, and (II) focusing on the time variation in excess pore water pressure, liquefaction, effective stress path in the seabed. This paper corresponds to (II).

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.3
• /
• pp.160-173
• /
• 2014

Seabed beneath and near coastal structures may undergo large excess pore water pressure composed of oscillatory and residual components in the case of long durations of high wave loading. This excess pore water pressure may reduce effective stress and, consequently, the seabed may liquefy. If liquefaction occurs in the seabed, the structure may sink, overturn, and eventually increase the failure potential. In this study, to evaluate the liquefaction potential on the seabed, numerical analysis was conducted using the expanded 2-dimensional numerical wave tank to account for an irregular wave field. In the condition of an irregular wave field, the dynamic wave pressure and water flow velocity acting on the seabed and the surface boundary of the composite breakwater structure were estimated. Simulation results were used as input data in a finite element computer program for elastoplastic seabed response. Simulations evaluated the time and spatial variations in excess pore water pressure, effective stress, and liquefaction potential in the seabed. Additionally, the deformation of the seabed and the displacement of the structure as a function of time were quantitatively evaluated. From the results of the analysis, the liquefaction potential at the seabed in front and rear of the composite breakwater was identified. Since the liquefied seabed particles have no resistance to force, scour potential could increase on the seabed. In addition, the strength decrease of the seabed due to the liquefaction can increase the structural motion and significantly influence the stability of the composite breakwater. Due to limitations of allowable paper length, the studied results were divided into two portions; (I) focusing on the dynamic response of structure, acceleration, deformation of seabed, and (II) focusing on the time variation in excess pore water pressure, liquefaction, effective stress path in the seabed. This paper corresponds to (I).

• Journal of the Korean Association of Geographic Information Studies
• /
• v.24 no.1
• /
• pp.126-137
• /
• 2021

Recently, the number of damages on social infrastructure has increased due to natural disasters and the frequency of earthquake events that are higher than magnitude 3 has increased in South Korea. Liquefaction was found near the epicenter of a 5.4 magnitude earthquake that occurred in Pohang, South Korea, in 2017. To explore increases in soil moisture index due to soil liquefaction, changes in the remote exploration index by the land cover before and post-earthquake occurrence were analyzed using liquefaction feasibility index and multi-cyclical Landsat-8 satellite images. We found that the soil moisture index(SMI) in the liquefaction region immediately after the earthquake event increased significantly using the Normal Vegetation Index(NDVI) and Surface Temperature(LST).

• Journal of the Korean GEO-environmental Society
• /
• v.21 no.1
• /
• pp.13-19
• /
• 2020

Recently, as the number of earthquakes increases in the Korean Peninsula and surrounding area, the importance of earthquake countermeasures and seismic design has been increasing. As a result, interest and concerns about liquefaction, which is one of the problems that concern the earthquake, are increasing. There are various methods that can assess the possibility of liquefaction by using geotechnical information for specific ground. However, direct comparisons of each method are not yet available. In this study, the two methods using the SPT-N value and the shear wave velocity among the methods for estimating the Cyclic Resistance Ratio (CRR) value required for the simplified liquefaction assessment method were compared. And the correction of the ground information required to use the two methods respectively was compared. As a result, more accurate evaluation results were obtained when the CRR value is calculated using the SPT-N values.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.2C
• /
• pp.83-94
• /
• 2008

In this study an effective stress analysis was performed to evaluate liquefaction potential and ground settlement for reclaimed sites. The effective stress model can simulate the stiffness degradation due to excess pore pressure and resulting ground deformation. It is applicable to a wide range of strain. An equivalent linear analysis suitable for low strain levels was also carried out to compare the effective stress analysis. Shear stress ratio calculated from an equivalent linear analysis was used to determine SPT blow count to prevent liquefaction. Depending on the magnitude of potential earthquake and fine contents, the SPT blow count was converted into an equivalent cone tip resistance. It was compared with the measured cone tip resistance. The measured elastic shear wave velocity and cone tip resistance from two reclaimed sites in Incheon were used to perform liquefaction analyses. Two liquefaction evaluation methods showed similar liquefaction potential which was evaluated continuously. The predicted excess pore pressure ratio of upper 20 m was between 40% and 70%. The calculated post-shaking settlement caused by excess pore pressure dissipation was less than 10 cm.