• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.574-577
• /
• 2010

이번 연구에서는 저속 비압축성 유체-구조 연성을 고려한 위상 최적화을 위해 새로운 모노리틱 해석을 개발한다. 이 새로운 해석 기법에서는 기존의 유체-구조 연성 시스템 해석 기법에서 유체와 구조 영역을 분리하고 연성 조건을 만족시키는 것과 다르게 하나의 일치된 해석 방정식을 유체 영역과 구조 영역에 동일하게 적용한다. 또한, 경계조건을 만족시키기 위하여 단일화 된 해석 방정식의 물성치를 바꾸어주는 새로운 방식을 제시하였다. 이 새로운 방법에서는 유체, 구조 영역을 분리하지 않고 Navier-Stoke's 방정식과 선형 탄성식을 동시에 사용하였다. 또한, 유체-구조 영역이 연성 해석 중 변화하는 것을 반영하기 위하여 구조 변위를 이용하여 Deformation tensor를 계산하였고 이를 이용하여 변형 후에서의 Navier-Stoke 방정식의 미분을 계산하는 방법을 제안하였다. 그리고, 정상 상태 유체를 가정하고 속도에 비례하는 마찰힘인 Darcy's force 항을 Navier-Stoke 방정식에 넣고 이 마찰 힘의 크기를 변화시킴으로 해서 유체 방정식에서의 연성 경계 조건을 만족시켰다. 선형 탄성 방정식에서 Divergence이론을 이용해서 경계에서 작용하는 외력이 하는 일을 내부 시스템에 하는 일로 계산하였다. 개발된 모노리스 해석 방법을 이용하여 저속 비압축성 유체가 구조에 미치는 압축력을 계산하였고 이용하여 컴플라이언트 미케니즘을 설계하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.69-75
• /
• 2017

Ultra-high performance concrete and high ductile cementless composite are considered as promising construction materials because those exhibits higher performance in terms of high strength and high ductility. The purpose of this study is to investigate experimentally the compressive strength and tensile behavior of ultra-high performance concrete and high ductile cementless composite. A series of experiments including density, compressive strength, and uniaxial tension tests were performed. Test results showed that the compressive strength and tensile strength of alkali-activated slag based high ductile cementless composite were lower than those of ultra-high performance concrete. However, the tensile strain capacity and toughness of alkali-activated slag based high ductile cementless composite were higher than those of ultra-high performance concrete. And it was exhibited that a high ductility up to 7.89% can be attainable by incorporating polyethylene fiber into the alkali-activated slag based cementless paste.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.86-86
• /
• 2003

주편은 1차 냉각 지역인 수냉 몰드를 통과한 후, 2차 냉각 지역에서 guide roll, pinch roll 그리고 driven roll등에 의해 반복적인 압축하중을 받고 있으며, roll과 roll사이에서는 철정압에 의한 주편 bulging 현상이 발생하고 주편의 표면은 인장응력을 받게 된다. 특히 연속주조 중 주편의 변형기구가 단순 탄소성 변형 이 아닌 creep에 의한 변형임을 고려할 때, 2차 냉각 지역에서 주편의 표면은 전술한 압축 및 인장변형 이 반복되는 저주기 고온 피로 환경을 거침을 알 수 있다. 본 연구에서는 탄소함량에 따른 주편의 bulging시의 크랙 발생에 미치는 저주기 고온 피로의 효과를 조사하였다. 또한, 용체화 처리 온도에서 시험 온도까지의 냉각 속도의 영향을 조사하기 위하여 1$^{\circ}C$/s 및 1$0^{\circ}C$/s로 냉각 속도를 변화시켜 열간 연성 곡선을 작성하였다. 본 연구에서 얻어진 결과는 다음과 같다. 저탄소강의 경우는 저주기 피로의 영향이 관찰되지 않았으며, 중탄소강의 경우, 저온에서는 저주기 피로로 인해 열간 연성이 증가하였으나, 고온에서는 변형유기 페라이트의 생성으로 인해 열간 연성 이 감소하였다. 고탄소강의 경우는 저주기 피로로 인하여 열간 연성이 모든 온도 구간에서 증가하였다. 또한 용체화 처리후 시험 온도까지의 냉각 속도가 감소함에 따라 열간 연성이 증가하였는데, 이는 입 계 석출물의 조대화로 인해 열간 연성이 증가하는 것으로 판단된다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.2
• /
• pp.183-189
• /
• 2020

The purpose of this study is to investigate the compressive and tensile properties of high volume slag cement-based fiber-reinforced composite incorporating phase change material. Four mixtures were determined according to calcium hydroxide and expansive admixture, and the compressive strength and tension tests were performed. Test results showed that four mixtures showed a compressive strength over 51MPa and a tensile ductility over 3.2%. It was observed that calcium hydroxide and expansive admixture influenced the compressive and tensile performance, and the strength, ductility, and cracking patterns of composite could be improved by including proper amount of calcium hydroxide and expansive admixture.

• Journal of the Korea Concrete Institute
• /
• v.14 no.4
• /
• pp.530-539
• /
• 2002

In designing the boundary confinement of shear walls, the current design provisions and recommendations are empirical and prescriptive; they specify a certain confinement length and details, regardless of the actual requirement of ductility Therefore, they are inappropriate to the performance based-design. The purpose of the present study is to develop a ductility design method that Is applicable to the performance based-design of shear wall. For the purpose, experimental studies were performed to investigate variations in the ductility of shear walls with the length of the boundary confinement. Five specimens modeling the compressive zone of cross sections with different confinement area were tested against eccentric vertical load. Through the experimental studies, strength, ductility, and failure mode of the compression zone were investigated. In addition, nonlinear numerical analyses for the overall cross-sections of shear wall were performed to investigate variations of the stress and strain profiles with the length of compression zone. On the basis of the experimental and numerical studies, a ductility design method for shear wall was developed. By using the proposed design method, for a given ductility demand, the area of lateral confinement and corresponding reinforcement ratio can be precisely determined so that the ductile behavior and economical design are assured.

• Journal of the Korea Concrete Institute
• /
• v.13 no.6
• /
• pp.553-560
• /
• 2001

The ductility capacity should be estimated for inelastic analysis and design of reinforced concrete flexural members. Therefore, to estimate the ductility capacity, the model of moment-curvature relationship of reinforced concrete flexural member is assumed in this study. The curvature, rotation, and displacement(deflection) of reinforced concrete cantilever beams are analyzed and tested. The analytical results are compared with the test results. According to the analytical and test results, the assumed model of moment-curvature relationship in this study is adequate in flexural analysis of reinforced concrete members because the analytical results are well agreed with the test results, and it is resonable to express the ductility capacity in the rotation or displacement ductility, Because the curvature ductility is the limited index in a certain section. It is investigated that the ductility capacity is proportional to lateral reinforcement and compression reinforcement and inversely proportional to tension reinforcement.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.121-122
• /
• 2008

In this paper, computational analysis on the steady-state and transient behaviors of the valve system is discussed. Fluid-structure interaction (FSI) is taken into account using ADINA software. The computational results are experimentally validated.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.9
• /
• pp.61-68
• /
• 2012

The main objective of this study is to develop an analytical model for the resilient modulus of EPS geofoam when it is applied for flexible pavement as a subgrade material. This analytical model has been developed based on the results from triaxial compression tests. And this model can be used to analyze the flexible pavement structure using the finite element method by developing a program or modifying an existing program for any desired purposes. The results of this study show that the EPS geofoam as a replacement material for subgrade in flexible pavement is a feasible alternative to natural weak soils.

• Journal of the Society of Disaster Information
• /
• v.13 no.4
• /
• pp.491-498
• /
• 2017

The primary objective of this research is to develop a rutting performance prediction model of flexible pavement. Extensive laboratory testings were conducted to achieve the objective. A new test method employing repetitive axial loading with confinement was also adopted to estimate the rutting performance of asphalt concrete in the research. The rutting prediction model employes a layer-strain theory. The required rutting coefficients for the prediction model were determined through the laboratory rutting characterizations of the asphalt concrete layer materials. Within the limits of this study, a laboratory rutting prediction model of flexible pavement using repetitive axial loading test was presented. It is noted that the developed rutting prediction model simulates propery the behaviors of flexible pavement layer materials.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.6
• /
• pp.547-556
• /
• 2014

This paper discusses a one-way fluid structural interaction (FSI) analysis and shape optimization of the impeller blades for a 15,000 HP centrifugal compressor using the response surface method (RSM). Because both the aerodynamic performance and the structural safety of the impeller are affected by the shape of its blades, shape optimization is necessary using the FSI analysis, which includes a structural analysis for the induced fluid pressure and centrifugal force. The FSI analysis is performed in ANSYS Workbench: ANSYS CFX is used for the flow field and ANSYS Mechanical is used for the structural field. The response surfaces for the FSI results (efficiency, pressure ratio, maximum stress, etc.) generated based on the design of experiments (DOE) are used to find an optimal shape for the impeller blades, which provides the maximum aerodynamic performance subject to the structural safety constraints.