• Journal of the Korean Society for Railway
• /
• v.17 no.1
• /
• pp.43-51
• /
• 2014

In the earth structures of railways, large coarse granular materials are widely used as fill materials. However, experimental studies that consider the dynamic properties of these coarse granular materials have rarely been carried out in Korea due to the lack of a large scale test apparatus in this country. In this study, large scale cyclic triaxial tests were carried out for materials such as reinforced roadbed (subballast, graded crushed stone), transition zone gravel, and the upper subgrade of a railway. These specimens were prepared according to certain conditions (dry unit weight, grain size distribution, and so on) specified in the Korea railroad design standard. Based on these large triaxial test results, normalized shear modulus and damping ratio curves according to small strain level are suggested. A model and coefficients for each material are also proposed.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.5
• /
• pp.5-15
• /
• 2011

Recent increase of large scale construction near costal area has also increased the application of soft ground treatment. As a result, solidification with cement and lime which increases stability and durability of soils, is frequently used for surface layer stabilization in soft ground site. While stabilization of very soft clay with high plasticity and compressibility has widely been studied, studies on silty clay with low plasticity and compressibility are relatively rare. In this study, after stabilizing low plasticity silty clay of Songdo area with cement and lime under various water contents, mixing ratio, and curing time, uniaxial compression test and plate load test were performed. Strength properties from both tests were considerably consistent. And trackability of construction equipment on the treated surface layer of dredged land was estimated. Finally, optimum mixing condition for Songdo silty clay was proposed.

• Journal of the Korea Concrete Institute
• /
• v.18 no.6 s.96
• /
• pp.743-748
• /
• 2006

This paper presents results of an experimental study conducted to investigate the effect of volume fraction of fibers on the mechanical properties of a fiber-reinforced, lightweight aggregate concrete(FRLAC) that was produced without an autoclave process. The FRLAC enhanced the strength of lightweight, cellular concrete by adding polypropylene fibers and lightweight aggregates. To investigate the effect of volume fraction of fibers on the mechanical behavior of FRLAC and to determine the optimal volume fraction of fibers, a series of compression and flexural strength tests on FRLAC specimens with various fiber volume fractions(0%, 0.10%, 0.25%, 0.50%) were conducted. It was observed from the tests that a 0.25% volume fraction of fibers maximized the increase in the strength of FRLAC and the fibers controlled cracking in FRLAC.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.6
• /
• pp.117-126
• /
• 2005

The chemical property analysis on the deposited clay using scanning electron microscope and energy dispersive x-ray spectrometer were performed. Also, the triaxial compression tests and consolidation tests using NaCl aqueous solution and leachate as substitute pore (or saturated) water in samples were carried out to find out the behaviour characteristics of strength and deformation of contaminated deposited clay. from the chemical composition analysis results of clay samples, the magnitudes of composition ratio were revealed in the order of O, C, Si, Al, and Fe. Of these, why the ratio of carbon appeared to be large is estimated as due to the increase of the phyto-planktons after the construction of tide embankment. In the triaxial compression test and consolidation test results, the shear strength and compression properties have increased with the increase in concentration of contaminant (NaCl). This phenomenon is considered as to be caused by the changes of soil structure to flocculent structure owing to the decrease in the thickness of diffuse double layer in proportion to increase in the concentration of electrolyte.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.2
• /
• pp.191-203
• /
• 1992

This paper dealt with the statistical values including mean, standard deviation, variance and coefficient of variation for 14 soil parameters available of Lade's double work-hardening model in order to predict the behaviour of granular soil. 27 sets of all 14 parameters for Baekma river sand were determined by regression using raw data acquired from 12 isotropic compression tests and 9 triaxial compression tests with the variation of confining pressure of 1, 2, and $4kg/cm^2$ respectively 3 times performed during this study. The characteristics of each parameters were investigated. By determining the range of the upper and lower bound dependent on the increase and decrease of the standard deviation from mean value of parameters, sensitivity of all the parameters was scrutinized, by which in turn the influence of experimental error generated inevitably during tests on the determination of soil parameters was also examined.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.10
• /
• pp.55-62
• /
• 2012

In this research, the algorithm for simulating specific grain size distribution(GSD) with large diameter granular material was developed using the distinct element analysis program $PFC^{3D}$(Particle Flow Code). This modeling approach can generate the initial distinct elements without clump logic or cluster logic and prevent distinct element from escaping through the confining walls during the process. Finally the proposed distinct element model is used to simulate large triaxial compression test of the rockfill material and we compared the simulation output with lab test results. Simulation results of Assembly showed very well agreement with the GSD of the test sample and numerical modeling of granular material would be possible for various stress conditions using this application through the calibration.

• Geotechnical Engineering
• /
• v.6 no.3
• /
• pp.65-76
• /
• 1990

A series of consolidated drained and untrained cubical triaxial tests were performed to investigate three dimensional strength characteristics of compressible sand. All specimens, which are formed by deposisting a fine sand loosely, were used. Failure strength in terms of effective stress analysis was greatly influenced by the variation of intermediate principal stress and so was failure criterion The adjusted effective frictional angles obtained by the stress state projected on the same octahedral plane showed almost same value, while the measured effective frictional angles showed considerable difference depending on the drainage conditions. Results of total stress analysis in undrained test turned out to fit Tresca's failure criterion well, but results of effective stress analysis turned out to fit Lade's failure criterion well.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.6 no.2
• /
• pp.263-275
• /
• 2002

In general, the values of shear strength properties of rubble stones have been given quoting from Japanese empirical recommendation when breakwater and offshore structures of port and harbor facilities were designed in Korea. but by large-scale triaxial test(specimen diameter 30cm, specimen height 60cm) carried out in Korean Water Resources Corporation in 2001, for the first time in korea, shear strength properties of rubble stones are evaluated directly. These are compared with the Japanese empirical recommendation. Therefore, the value of shear strength properties of rubble stones have been usually given quoting from Japanese empirical recommendation without laboratory or in-situ tests, but the results of this study state that shear strength properties of rubble stone can be rationally determined and shear behavior characteristics of rubble stone can be invesgated by large-scale triaxial test

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.4
• /
• pp.53-59
• /
• 2012

In this study, strength and durability of a geo-polymer grout material(HIT) was investigated through unconfined compression strength tests(UCS)), scanning electron microscope(SEM), elution tests, and surface observations. UCS tests showed high initial strength and rapid continuous strength increments when compared to labile wasser glass(LW) and space grouting rocket system (SGR) grout materials, which showed strength reduction after 28 days. The higher strength was also reflected in SEM results which showed calcium silicate hydroxide(C-S-H) gels of the dense hydrate range, indicating higher strength and durability. Additionally, elution tests and grout surface observations showed HIT was in good condition and the decrease in weight was minor when under water for six months. LW and SGR showed the grout surface to be constricted and lower durability due to higher weight increase. These results and observations show HIT to be better suited for coastal structural applications than LW and SGR in long terms of strength and durability.

• Journal of the Korean Geosynthetics Society
• /
• v.5 no.4
• /
• pp.19-25
• /
• 2006

To examine the general features of a sand-clay composite triaxial test by making specimen varying ratios of diameters (dw) of sand columns that are installed on the soft ground as drains to diameters (de) of drain zone so called drainage space ratio (n=de/dw), densities of the granular columns, and strength of soft soils round around. I also conducted a test to research the reinforcement ability and effects of the ground when the granular columns are wrapped with supplementary materials such as geotextile. The results of the triaxial compression test showed that the shear strength increase is much big when the granular columns are wrapped with supplementary materials, while the shear strength increases as the diameter and density of the granular column increase in general. Also the drainage space ratio shows a distinct increase just below 3 and a similar shear behavior to sand is appeared. The pore water pressure coefficient decreases as the drainage space ratio decreases, however, when the drainage space ratio is less than 3~4, it declines significantly as shown in the results of shear behavior.