• Ceramist
• /
• v.8 no.1
• /
• pp.50-56
• /
• 2005

압전재료의 다양한 에너지 변환특성 중 기계-전기 에너지간 변환 특성만을 이용하고자 하는 경우로 한정하고, 압전재료의 물성 및 진동모드, 재료물성 평가 사례들을 요약하여 소개하였다. 그러나 이상에서 설명한 압전특성은 매우 개략적인 개념으로서 우수한 압전 응용부품을 개발하기 위해서는 몇 가지 유의할 사항들이 있다. 압전재료는 보다 기본적으로 열에너지, 기계에너지, 전기에너지, 나아가서 Maxwell 방정식에 의해서 전기장과 연결되는 자기에너지까지도 연결시켜서 상호간에 에너지 변환작용을 일으킬 수 있는 특성을 가진다. 기계적 변형(S) = 탄성변형효과 + 역압전효과 + 열팽창효과 전기적 변위(D) = 압전효과 + 유전효과 + 초전효과 즉, 압전 응용부품이 온도변화 및 자기장이 인가되는 환경에서 순수하게 압전현상만을 이용하고자 한다면, 응용분야 및 주위환경에 따라 압전세라믹 소자가 외부 환경변화에 반응을 하지 않도록 적절한 차단 대책을 수립하여야만 한다. 그러나 압전재료의 외부 자기장의 변화에 대한 반응도는 전기장에 대한 반응도에 비해서 매우 작으므로 통상 무시해도 무방하다고 본다. 그리고 압전재료에서 전기장-기계장의 선형성이 보장되는 크기에는 뚜렷한 한계가 있고, 선형성 영역을 벗어나면 이력특성에 의해 비선형 특성 및 포화상태를 보이게 된다는 점 또한 주의하여야 할 점이다. 또한 압전특성은 Curie 온도이하에서만 존재하고, 그 이상의 온도에서는 쌍극자들의 지나친 운동성에 의해 결정 대칭성이 변하여 압전특성이 소멸되므로 사용 온도 구간에 엄격한 제한을 두어야 함도 응용에 유의하여야 한다.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.2
• /
• pp.103-108
• /
• 2004

In this paper, all the materials constants of the PMN-32%PT single crystals grown by the solid state crystal growth method were measured by the resonance method. PMN-PT crystals of tetragonal symmetry have six elastic constants, three piezoelectric constants and two dielectric constants for their independent material constants. These materials constants were extracted from six sets of crystal samples of each different geometry to have different vibration modes respectively. Measured results showed that the crystal has larger electromechanical coupling factor k/sub 33/ (∼86%) and piezoelectric constant d/sub 33/ (∼1200pC/N) than conventional piezoceramics. Validity of the measurement was confirmed through comparison of the results with the impedance spectrum from finite element analysis of the samples and the results measured with a commercial do meter.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.246-251
• /
• 1995

유연구조물의 진동제어를 위해 압전필름 작동기를 사용하였고 이와 연계하 여 샘플링 과정을 고려한 DSMC를 구성하였다. 변수변화 및 외란의 경계치 를 알고 있다는 가정하에 시스템을 이산화시킨 후 제어기를 설계하였다. 일 반적으로 연속시간 시스템의 이산화 과정에서 정합조건의 가정이 보장되지 않기 때문에 제어기 설계시 이를 배제하였다. 이산시간 리아푸노프 이론을 근거로 DSMC의 존재성을 도출하였고, 이것에 기초하여 슬라이딩 모드가 발생되도록 불연속제어기를 설계하였다. 이때, 불연속게인을 상수로 하지 않고 RP의 위치에 따라 계속 새롭게 수정함으로써 슬라이딩 영역을 최소화 하였다. 그리고 기존의 DSMC 기법상에서 발생되는 슬라이딩 영역의 문제를 .betha. 등가제어기를 이용하는 이원화 방법으로 극복하였으며, 컴퓨터 시뮬 레이션을 통하여 제안된 기법의 설계 효율성 및 제어기의 강건성을 입증하였다. 향후, 제안된 기법에 대한 실험적 고찰 및 중요 제어인자에 대한 연구가 계속적으로 수행될 예정이다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.9
• /
• pp.899-906
• /
• 2009

In the present paper, dynamic characteristics and vibration control performance of a cylindrical shell structure are experimentally investigated and results are presented in the air and underwater conditions. End-capped cylindrical shell structure is manufactured and macro-fiber composite(MFC) actuators are attached on the inside-surface of the structure. Modal characteristics are studied in the air and under the water conditions and then equation of motion of the structure is derived from the test results. Structural vibration control performances of the proposed structure are evaluated via experiments with optimal control algorithm. Vibration control performances are presented both in the frequency and time domains.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.780-783
• /
• 2004

본 논문에서는 유한요소법과 등가회로법을 이용하여 윤곽 진동형 압전변압기의 특성을 해석하고 이를 통해 압전변압기의 매칭 임피던스와 기계 및 전기적 결합계수를 계산하였다. 실험적 결과를 통하여 수치해석의 타당성을 검증한 후, 진화 전략에 기초한 멀티 모드 함수의 최적 알고리즘을 이용하여 고효율 고전압 밀도 압전 변압기의 형상 최적화를 수행하였다. 최적화 과정에서의 계산 시간을 단축시키기 위하여 AWE(Asymptotic Waveform Evaluation)를 적용한 유한요소법을 사용하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.439-443
• /
• 2006

In this paper, a design of milli-gripper using piezoelectric actuator and flexible hinge structure has been suggested, and the dynamic characteristics of the milli-gripper has been analysed and improved. The milli-gripper consists of the operating and amplifier parts, and the perfomance of the gripper be heavily influenced by base excitation disturbances. The dynamic characteristics of milli-gripper has been measured by the FRF based on experimental modal analysis. It has been found by a series of experiments that the performance of the milli gripper using PID control is made a remarkable improvement in terms of gripping forces.

• Journal of KSNVE
• /
• v.9 no.1
• /
• pp.70-76
• /
• 1999

This paper presents a pseudo-sensor-output-feedback(PSOF) method for the vibration suppression of the flexible piezoelectric smart structures. This method reduces the modeling errors using pseudo sensors in the output equation formulation. It also reduces computation time in practice. since the output equation does not need the state observer required in the state space equation. Experimental works are performed for the validation of theoretical predictions with the piezoelectric sensor and actuator bonded on the cantilever beam. An algorithm based on the sliding mode control theory is developed and analyzed for the robustness to the modeling errors and parameter uncertainties. This study also discusses the characteristics of the active and semi-active systems.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.8
• /
• pp.1197-1205
• /
• 2001

The vibrational characteristics of Langevin-type piezoelectric torsional transducers, which consist of a couple of piezoelectric discs and a couple of elastic blocks, have been studied theoretically and experimentally in this paper. The differential equations of piezoelectric torsional motion have been derived in terms of the circumferential displacement and the electric potential. Solutions of the boundary-value problem have yielded the natural frequencies and mode shapes of the transducers. The theoretical solutions have been verified by comparing the numerical results with experimental ones.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.2
• /
• pp.115-124
• /
• 2004

This paper suggested the vibration characteristic improvement by variation mode of ring type ultrasonic motor. Design for the piezoelectric ceramic and elastic body of stator were calculated by the finite element method(FEM) that consider the resonance frequency, vibration mode and coupling efficiency etc. Through the result of vibration analysis from 6 order mode to 8 mode, the 7 order mode was gained very an excellent results that it was the coupling efficient, minimum power loss and bending vibration value. Here over 7 order mode, was acquired that an output current for input voltage was very a large increased results. The result of vibration calculation, from thickness 0.5[mm] to 2[mm], know the fact that the vibration displacement at 0.5[mm] is an high value too. From such analysis result, this paper was manufactured the ultrasonic motor of outer diameter 50[mm], inter 22[mm] having the about 43.86[KHz] resonance frequency. We have gated that a simulation result is 42.2[KHz] and an experiment result is 43.86[KHz]. Then, a propriety of this paper was established the result almost similar to though comparison, investigation of simulation and experiment result.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.4A
• /
• pp.287-293
• /
• 2011

This paper investigates the applicability of a piezoelectric cantilever for energy supply of wireless sensor node used in structural health monitoring of bridges. By combining the constitutive equation of piezoelectric material and the dynamic equation of cantilever structure, the coupled governing equation for cantilever equipped piezoelectric patches has been addressed in matrix form. Forced excitation tests were carried out to validate the numerical model and to investigate the power output characteristics of the energy harvester. From the numerical simulation based on the measured bridge accelerations under KTX, Saemaul, Mugunghwa trains, the peak powers generated from the device were found to be 28.5 mW, 0.65 mW, 0.51 mW respectively. It is revealed from the results that bridge vibrations caused by moving loads is not a practical source for energy harvesting because of its low acceleration level, low frequency and short duration.