• Title/Summary/Keyword: 압력코어 가스

Search Result 18, Processing Time 0.036 seconds

Experimental research trends on Pressure Core Samples (압력 코어를 이용한 현장 가스 하이드레이트 함유 시료 연구 현황)

  • Lee, Joo Yong;Jung, Jaewoong;Ryu, Byung Jae;Lee, Jaehyung;Kim, Sejoon
    • 한국신재생에너지학회:학술대회논문집
    • /
    • 2011.11a
    • /
    • pp.124.1-124.1
    • /
    • 2011
  • 저온 고압의 환경에서 안정한 하이드레이트 함유 퇴적물 연구를 위하여 현장의 압력을 유지하여 코어를 회수할 수 있는 압력 코어러 (Pressure Corer)가 개발된 이후로 다양한 방법으로 압력코어를 이용한 연구가 진행되어 왔다. 하이드레이트의 안정영역 특성상 일반 코어러 샘플에서는 하이드레이트 함유 퇴적물의 회수가 용이하지 않았던 이유로 압력코어샘플응 이용한 현장 하이드레이트 함유 퇴적물의 연구는 필수적이다. 초기 단계에서는 압력코어를 이용한 비파괴 검사와 단순 감압 시험이 이루어졌다. 비파괴 검사를 통하여서는 X-ray 단면, 감마 밀도 (gamma density), 음파 속도 등이 측정 되었으며 감암 시험을 통하여서는 시료 내 하이드레이트 함유량을 산정하였다. 감압 후 다양한 지화학 분석이 후행되었다. 가스 하이드레이트 함유 퇴적물의 물성과 생산 거동이 점차 부각됨에 따라 압력코어 시료를 순간 감압하여 액체 질소에 보관하였다가 압밀시험, 삼축 압축 시험 등 물성 시험이 수행되었으며 수행 동안 X-ray 단면, 비저항, 음파 속도 등의 물성측정이 이루어졌다. 또한 액체 질소 보관 시료를 이용하여 감압법, 열염수 주입법, 열자극 법 등을 적용하여 생산 실험을 수행하기도 하였다. 이후에 압력코어 시료 절단 및 이동 시스템이 개발됨에 따라 보다 다양하고 많은 연구자 들이 압력코어 시료를 이용할 수 있게 되었으며 물성 연구뿐만 아니라 미생물 연구에 까지 압력코어 시료가 사용되게 되었다. 최근에는 절단 시료를 이용한 생산 실험 연구 또한 진행되었다.

  • PDF

Gas Hydrate Exploration by using PCS(Pressre Core Sampler): ODP Leg 204 (압력코어를 이용한 가스 하이드레이트 탐사: ODP Leg 204)

  • Lee Young-Joo
    • Economic and Environmental Geology
    • /
    • v.38 no.2 s.171
    • /
    • pp.165-176
    • /
    • 2005
  • Natural gas in deep sediment may occur in three phases based on the physical and chemical conditions. If the concentration of gas in pore water is less than the solubility, gas is dissolved. If the concentration of gas is greater than its solubility (water is saturated or supersaturated with gas), gas occurs as a fee gas below the gas hydrate stability Lone (GHSZ) and is present as solid hydrate within the GHSZ. The knowledge of gas concentration in deep sediment appears critical to determine the phase of natural gases and to understand the formation and distribution of gas hydrate. However, reliable data on gas concentration are usually available only from the upper section of marine sediment by the headspace gas technique, which is widely used for sampling of gases from the sediments. The headspace gas technique represents only a fraction of gases present in situ because sediments release most of the gases during recovery and sampling. The PCS (Pressure Core Sampler) is a downhole tool developed to recover a nominal $1{\cal}m$ long, $4.32{\cal}cm$ diameter core containing $1,465cm^3$ of sediment, pore water and gas at in situ pressure up to 68.9 MPa. During Leg 204, the PCS was deployed at 6 Sites. In situ methane gas concentration and distribution of gas hydrate was measured by using PCS tool. Characteristics of methane concentration and distribution is different from site to site. Distribution of gas hydrate in the study area is closely related to characteristics of in situ gas concentration measured by PCS.

Calculation of Gas Hydrate Saturation Within Unconsolidated Sediments (미고결 퇴적층내 가스하이드레이트 포화도 계산)

  • Kim, Gil-Young
    • Geophysics and Geophysical Exploration
    • /
    • v.15 no.2
    • /
    • pp.102-115
    • /
    • 2012
  • The purpose of this paper is to review several different methods calculating gas hydrate saturations. There are three methods using downhole log data, core data (including pressure core), and seismic velocity data. Archie's equation using electrical resistivity of downhole log data is widely used for saturation calculation. In this case, Archie's parameters should be defined accurately. And the occurrence types of gas hydrate significantly affect to saturation calculation. Thus saturation calculation should be carefully conducted. The methods using chlorinity and pressure core data are directly calculated from core sample. So far, the saturation calculated from pressure core gives accurate and quantitative values. But this method is needed much more time and cost. Thus acquisition of the continuous data with sediment depth is realistically hard. The recent several results show that the saturation calculated from resistivity data is the highest values, while the value calculated from pressure core is the lowest. But this trend is not always absolutely. Thus, to estimate accurate gas hydrate saturation, the values calculated from several methods should be compared.

The status of Gashydrate Drilling Campaign 2007 in Korea (가스하이드레이트 시추 현황)

  • Kim, Il-Soo;Park, Keun-Pil
    • 한국신재생에너지학회:학술대회논문집
    • /
    • 2007.11a
    • /
    • pp.557-559
    • /
    • 2007
  • 정부는 2005년부터 가스하이드레이트 개발사업단을 발족시켜 국내의 가스하이드레이트 부존 형태와 매장량 평가를 위해 노력하고 있다. 2005년 2차원 정밀 물리탐사, 심해 퇴적물 채취 및 다각적 분석연구사업이 수행되었고, 2006년도에는 3차원 물리탐사, 개발기술을 위한 연구 및 지질재해${\cdot}$안정성 연구 등이 수행되었다. 또한 2007년 상반기에 동해 지역에서 해저면 표면에서 피스톤 코어를 이용하여 실물 샘플을 채취하는 데 성공하였다. 기존에 취득된 다양한 자료를 면밀히 분석하고 해석한 결과를 바탕으로 2007년도 하반기에 시추를 진행 중에 있다. 시추를 통하여 동해지역의 가스하이드레이트의 부존 형태 파악 및 추정 매장량을 산출할 수 있는 좋은 결과가 취득될 것으로 기대하고 있다. 시추는 다양한 검층 및 압력코어 시스템을 포함한 코어채취가 수행되고 있다. 취득된 시추 결과를 이용하여 사업단은 가스하이드레이트 개발을 위한 보다 나은 결과를 도출한 것이며 이를 통해 미래 에너지원의 확보 및 자원 강국으로 가는 초석을 마련하게 될 것으로 기대한다.

  • PDF

Development of a Pressure Core Sampler with Built-in Data Logging System (데이터 기록 장치가 내장된 PCS (Pressure Core Sampler)의 개발)

  • Kim, Sang Il;Cho, Young Hee;Ki, Jung Seck;Kim, Dong Wook;Lee, Kye Kwang;Kim, Hae Jin;Choi, Kook Jin
    • The Journal of Engineering Geology
    • /
    • v.24 no.3
    • /
    • pp.423-429
    • /
    • 2014
  • Development of a reservoir pressure core sampler (PCS) with a built-in data logging system (DLS) for recording real-time temperature and pressure observations is critical in domestic hydrocarbon production to accurately measure and monitor reserves of shale gas, coalbed methane, and gas-hydrate. Another purpose of this new technology is to minimize the loss of gas from the core as the drill core is collected. This is accomplished by maintaining the pressure of the sample from the moment the drill core is obtained at depth, thus allowing an accurate analysis of shale gas, coalbed methane gas, and gashydrate within the core. Currently, the United States and European countries have monopolized the development and marketability of PCS technologies. We are thus developing a reservoir PCS by analyzing the operating principle and mechanisms of the existing PCS, and by conducting tests on the existing PCS. We further aim to develop a PCS with a maximum operating pressure of 100 bar, a maximum operating temperature of $-20^{\circ}C$ to $40^{\circ}C$, and a pressure loss rate of 10%.

Development of PCS and an experiment for performance evaluation (PCS(Pressure Core Sampler) 개발 및 성능평가실험)

  • Lee, Ha-jung;Kim, Hae-jin;Lee, Gye-gwang;Jung, Hyo-seok;Son, In-rak
    • Journal of Advanced Marine Engineering and Technology
    • /
    • v.39 no.9
    • /
    • pp.973-980
    • /
    • 2015
  • With their wide geographical distribution, unconventional resources are continuously compared against conventional resources, but their development is expanding because TRRs (Technical Recoverable Resources) are similar to conventional resources. In particular, there is active development of unconventional gas resources such as shale gas, tight gas, CBM (coalbed methane) and gas hydrate. However, it is difficult to calculate the material properties of unconventional resources, especially the gas content, with current geophysical logging technology. Additionally, some overseas companies have monopolies on related equipment and materials. Therefore, this study developed a reservoir PCS (Pressure Core Sampler). It can collect core samples without gaseous loss by maintaining high pressure from the moment the core is sampled and record pressure and temperature in real time. Successful performance testing was also carried out for official verification of the manufactured PCS. The reservoir PCS will contribute to the acquisition of geophysical well logging data as well as accurate and reliable cores.

Development of a Rupture Disk for Pyrostarters (파이로스타터용 럽쳐디스크 개발)

  • Park, Ho-Jun;Hong, Moon-Geun;Lee, Soo-Yong
    • Proceedings of the Korean Society of Propulsion Engineers Conference
    • /
    • 2009.05a
    • /
    • pp.219-222
    • /
    • 2009
  • Pyrostarters play a role as a turbopump starter in liquid propellant propulsion systems by supplying pressurized gas to power turbines for engine start. A rupture disk in pyrostarters, which is usually installed behind a nozzle throat, not only isolates the charged solid propellants from the external environment but also improves the ignitability of the solid propellants by increasing a chamber pressure at the beginning of combustion. Experimental tests have been performed to study the effects of rupture disk thickness, depth and shape of scores, and pressure build-up rates on burst pressures and burst diameters. The experimental results show that the developed rupture disk fulfills the performance requirements expected in a real operational condition.

  • PDF

Technical Consideration of Elastic Wave Measurements of Gas Hydrate-bearing Sediments in Lab-Scale (GH 함유 퇴적물 실험실 스케일 탄성파 측정 기법의 기술적 고찰)

  • Jung, Jaewoong;Lee, Joo Yong;Lee, Jaehyung;Kim, Sejoon
    • 한국신재생에너지학회:학술대회논문집
    • /
    • 2011.11a
    • /
    • pp.125.2-125.2
    • /
    • 2011
  • 청정 에너지원으로 높은 잠재력을 가지고 있는 가스하이드레이트는 상업적 기술개발이 미확보된 상태이다. 현재 전 세계적으로 가스하이드레이트 개발 및 생산에 관한 연구가 활발히 진행되고 있으며 이에 대한 기초자료로서 가스하이드레이트가 함유된 퇴적층의 물성자료가 필요하다. 특히, 현장 시료에 대한 물성 측정은 향후 가스하이드레이트 개발 및 생산 계획을 수립하는데 있어서 매우 중요하다. 탄성파 측정 결과는 다른 물성 들에 비하여 하이드레이트 함유 시료의 성형과정에 큰 영향을 받는다. 또한 그 외의 실험 경계조건과 취득 자료의 처리 과정에도 매우 민감하게 반응한다. 따라서 측정을 하는 과정은 물론 측정 후 자료의 활용 과정에서 다양히 고려해야 할 점들이 있다. 본 연구에서는 인공 모래를 이용하여 다양한 조건에서 탄성파 속도를 측정한 후 그 결과를 토대로 하여 기존의 연구 결과와 비교하여 음파 측정연구 시 고려해야 할 기술적 사항 들을 정리해 보았다. 실험에 사용된 장비는 고압의 퇴적층을 모사할 수 있는 압력셀과 메탄과 염수 주입에 사용되는 유체 주입장비, 하이드레이트 형성을 위한 온도조절장비, 자료 획득 장비로 구성되어 있다. p파 속도는 음파 송수신장비를 사용하였다.

  • PDF

Dynamic Performance of Natural Gas Injection Valve for Heavy-Duty CNG Dual Fuel Engine (대형 CNG 혼소 엔진용 천연가스 분사밸브 동특성 연구)

  • Kim, Yong-Rae;Choi, Young
    • Journal of the Korean Institute of Gas
    • /
    • v.21 no.5
    • /
    • pp.9-15
    • /
    • 2017
  • Natural gas fuel has known to be very promising in terms of abundancy and economic value. Therefore it is widely treated as research topics in a variety field of production, storage and utilization. Natural gas has become one of the major sources for the power generation by using internal combustion engines(ICE). Development of natural gas fuel injection device should be preceded to realize a reliable natural gas fuel supply system for a MW class power generation reciprocating ICE. In this research, an injection valve which consists of solenoid and body part with a moving plate was designed and its dynamic performance was experimented in the engine-like environment. Displacement length and diameter of an armature and diameter of a solenoid coil were tested at former study. In this research the effect of materials of solenoid core, size of main housing inlet and supply gas pressure are examined.