• Journal of Energy Engineering
• /
• v.26 no.3
• /
• pp.71-77
• /
• 2017

In the event of loss of coolant accident (LOCA) and station black out (SBO) in the primary system of a nuclear reactor, the coolant water should be injected to reactor coolant system (RCS) without any intervention of operators or active components. To satisfy the requirements, hybrid safety injection tank (Hybrid SIT) was suggested by Korea Atomic Energy Research Institute (KAERI). The pressure equalizing time of Hybrid SIT is an important parameter to determine the timing of coolant injection. To predict the pressure equalizing time of the Hybrid SIT, a separate effect test facility was constructed and sensitivity tests were conducted in various conditions. The main parameter determining the pressure equalizing time was obtained from separate effect test (SET) results. The wall of condensation on the inner wall of SIT and direct contact condensation on the water surface affected to the pressure equalizing time very much. In this study, the effect of each condensation phenomena on pressure equalizing time was quantitatively analyzed from results of SET and a prediction method of pressure equalizing time was proposed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.766-773
• /
• 2021

Chemicals, such as ammunition, are disposable items that cannot be reused because of their operational characteristics. The reliability of the test process and test results are important factors in evaluating the performance of guns and ammunition. The pressure after firing is a crucial value in an acceptance test of guns and ammunition performance; hence, accurate measurements are required. The pressure in the artillery is measured using the copper crusher gauge. The compression amount of copper is converted into a pressure by either a length-pressure conversion table or conversion formula. Therefore, the exact measurement of the squeeze of the copper crusher is related directly to the correct estimate of the pressure. Currently, the pressure is measured manually by the operator, which always includes some human error. In this study, the cause of the measurement error was analyzed, and the automatic measuring system for copper crusher deformation was developed to minimize the error elements. A copper crusher could be measured using the probe sensor and CCD camera, and the Jig for stable positioning was also designed. A designated SW was also developed for the system operating and measurement-analysis. This measuring system through this study may be used for an ammunition stockpile reliability test and gun/ammunition acceptance test.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.1924-1928
• /
• 2009

다중패커시스템은 격리된 어느 특정 구간의 지하수를 채수할 수 있으며 그 구간의 온도, 압력 등의 자료를 연속적으로 관측할 수 있어 이를 통해 각 구간별 수리전도도를 구할 수 있다. 심도별 수직적 지하수두는 지상에서 연결 롯드를 통해 압력 측정 센서를 해당 심도까지 내려 롯드에서 설치된 압력 측정용 장비에서 관측할 수 있으며, 다중패커시스템을 이용한 수리시험으로는 양수시험, 순간충격시험, 간섭시험 등이 있는데, 본 논문에서는 순간충격시험을 이용한 결과를 제시하였다. 도출된 구간별 수리전도도를 다중패커시스템을 설치하기 전 나공에서 이중 패커를 이용한 정압주입시험의 결과와 비교하여 보았다. 다중패커시스템을 통해 획득된 심도별 지하수두는 정수두 (hydro-static)상태의 일정한 경향성이 없이, 각 심도에 존재하는 투수성 구조에 영향을 보이고 있음을 알 수 있었으며, 이는 다수의 관측공을 통해 수평 방향의 수리경사를 산출함에 있어 관측공의 심도에 대한 충분한 고려가 있어야 한다고 판단된다. 또한, 다중패커시스템을 이용한 수리시험 결과를 나공 상태에서 이중 패커를 이용한 정압주입시험 결과에 대해 심도별 도출되는 수리전도도가 국지적으로 분포하는 투수성 구조에 영향으로 인해 투수량계수 (transmissivity)로 환산한 유효 투수계수로 비교하여 결정질 암반의 수리 특성으로 제안하는 것이 타당한 것으로 분석되었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.12
• /
• pp.67-74
• /
• 2006

An unsteady blockage-correction method utilizing wall pressure distribution on the test section has been developed for the wall interference correction of a closed test-section subsonic wind tunnel. The pressure distribution along the test section wall was decomposed into Fourier series and a quasi-steady method based on a measured-boundary-condition method was applied to each Fourier coefficient. The unsteady correction for a complete test period was accomplished by recombining each corrected terms. The present method was validated by appling computed unsteady flows over a cylinder and an oscillating airfoil in the test sections. The corrected results by the present method agreed well with free-air condition.

• Geotechnical Engineering
• /
• v.11 no.2
• /
• pp.19-28
• /
• 1995

Based on the various test data acquired in the field, the large pressure chamber and the small pressure chamber, uplift behaviors and method of determining the ultimate uplift capacity of pile driven in small pressure chamber were studied. After uplift pile experienced 2 or 3 sudden slip due to increase of uplift load, complete pullout failure was occurred. Thus, it appears that the ultimate uplift capacity could be identified as the load at displacement where first slip occurs. The ultimate uplift capacity might be determined in every test and the disturbance after first uplift test could be recovered by adding one blow of the drop hammer, which had to depend on the model pile capacity.

• Proceeding of EDISON Challenge
• /
• 2016.11a
• /
• pp.63-67
• /
• 2016

본 연구에서는 극초음속 추진기관을 위한 고공환경 모사 설비 장치에서 시험부 안에 들어가는 시험 모델의 변수에 대해 고찰하였다. 시험부에 적용할 시험 모델을 대상으로 진행하고, 시험 모델 형상 변화에 따른 유동 특성을 파악하였다. 시험 모델에 대한 주요 변수는 폐색율, 각도, 받음각으로 설정하였으며, 해석은 EDISON_CFD에서 제공하는 정렬격자 기반 2차원 압축성 유동 범용 해석 SW로 진행하였다. 해석 결과를 통해 다양한 형상 변수에 따라 변화 되는 충격파 뒤의 압력층 두께를 확인 하였고, 압력층 두께가 두꺼워 질수록 시험 조건을 모사 할 수 없음을 확인하였다. 본 연구를 통해 형상 변수에 따른 극초음속 추진기관을 위한 고공모사설비에서 시험부에 적용될 시험 모델의 범위를 확인하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.19-28
• /
• 2014

Firing test of solid rocket motor with pintle-technology carried out and the measured pressure-time curve was compared with the values predicted by the internal ballistic and performance analysis. Without baffle, the measured combustion chamber pressure was similar with the predicted pressure at the beginning of combustion, but gradual increase in pressure, which was unexpected with the end-burning grain of which burning area is constant, was observed. A baffle was inserted to make uniform flow over the pintle. Unlike the thruster without baffle, the measured combustion chamber pressure was 1.4 times higher than the predicted value. Through the CFD simulation, 10% of total pressure loss of the flow was observed from combustion chamber to nozzle throat when the baffle was inserted. The measured pressure with baffle was predicted well by considering the total pressure loss in the internal ballistic modelling and performance analysis.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.217-225
• /
• 2003

The ground reinforcement effect of pressure grouting depends on grout penetration into ground. It is not, however, easy to predict the grout penetration in the design process because of the heterogeneity of ground conditions. This study investigates the proper grouting pressure and grouting method through laboratory model tests for pressure grouting using loose to medium dense crushed rock and sandy ground using specially designed and fabricated device. The optimum injection pressure, grout quantity and injection time are investigated through performing pressure grouting under changing conditions of injection in this test. From the test results, it was found that optimum injection pressure covers the range of 3 to 4kg/cm$^2$.

• 한국전기화학회:학술대회논문집
• /
• 2005.07a
• /
• pp.201-206
• /
• 2005

본 연구는 기 개발 완료된 천연가스차량용 200bar급 Type 3 복합재 압력용기를 개발로 축척된 핵심요소기술과 실질적인 경험을 바탕으로 수소연료전지 차량에 탑재할 350bar급 Type 3 복합재 압력용기에 대한 설계/해석과 시험평가의 핵심적인 사항을 고찰하였다. 설계/해석에는 350bar급 Type 3 복합재 압력용기에 대한 3차원 비선형 유한요소 모델링 및 해석기법이 제시되었고, 설계된 라이너형상과 와인딩 패턴을 이용하여 필라멘트 와인딩 공법으로 1차시제품을 제작하였다. 제작된 시제품에 대하여 파열시험 및 반복피로시험을 수행하여 설계/해석 기법의 타당성을 검증하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.1
• /
• pp.48-55
• /
• 2010

The purpose of this paper was to address the methodology of the air flow measurement using duct mach number that was considered area-weighed average obtained by total, static pressure and temperature measured at engine inlet duct. Without installing boundary rake, the prediction of air flow measurement was discussed. Actual air flow measurement and pressure value using pressure loss through inlet seal were described to improve the reliability and operability of altitude engine test facility.