• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.84-91
• /
• 2001

To investigate the aerodynamic characteristics of the on a road vehicle, experimenrs were performed at an Atmospheric Boundary Layer Wind Tunnel. The scaled model of an automobile with 1 : 3 scaling ratio was used. The Reynolds number based on the free stream velocity and model length was $7.93{\times}10^5$. The influence of crosswind to the stability of automobile was investigated by the pressure distribution measurements and flow visualization studies. with the variation of the angle of attack, the change in pressure coefficient depends highly on the flow separation regimes. The experimental and numerical results are compared and found to be in good agreements.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.38 no.9
• /
• pp.733-739
• /
• 1989

Fixed boundary MHD static equilibrium for the axisymmetric toroidal plasma is analyzed numerically. The Grad-Shafranov equation is solved using finite element method. The toroidal current term is expressed by plasma pressure and toroidal field function. The numerical results are compared to the Solovev analytic equilibrium for the verification of the solution. For SNUT-79 tokamak device in Seoul National University, the flux surfaces, the toroidal current profiles, the safety factor q and average beta values are obtained when the p and g profiles are varied.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.12
• /
• pp.945-953
• /
• 2008

Laminar film condensation of saturated vapor in forced flow over a flat plate is analysed. The problem is formulated as exact boundary-layer solution and integral approximate solution. From numerical solutions of the governing equations, it is found that the energy transfer by convection and the effect of inertia term in the momentum equation in negligibly small for low pressure but quite important for high pressure. The condensate rate, liquid-vapor interfacial shear stress and local heat transfer are strongly dependent on the reduced pressure $P_r$ and the modified Jacob number Ja/Pr.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.04a
• /
• pp.34-34
• /
• 1998

일반 항공기 및 상용 복합 구조재의 경우에는 내부에 결함이 생길 경우 유지 및 보수가 용이하나 복합재 압력 용기의 경우에는 다양한 환경 변화를 겪게 되며 또한 유지 및 보수가 힘들다는 제약 조건이 있으므로 단열재로 사용되는 인슈레이션 고무와 FRP간의 접착, 가황 고무와 미가황 고무 사이의 접착 등 여러 가지 이종 재질들 간의 접착이 매우 중요한 변수가 될 뿐만 아니라 압력 용기의 전체적인 성능에도 상당한 영향을 미치게 된다. 이러한 시스템들은 제작 조건에 따라 결함이 발생하는 빈도가 차이가 나며 특히 가혹한 환경 조건하에서도 내구성을 보여야 하므로 본 실험에서는 다양한 환경 조건, 성형 조건을 가지는 FRP/고무, 고무/고무 접착 시스템의 계면 접착력을 측정한 후 이로부터 환경 노화에 저항성이 강한 최적의 접착제 및 접착 조건 등을 확립하고자 하였다.

• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.95-96
• /
• 2013

Numerical simulations are conducted to investigate the mechanism of spontaneous ignition of hydrogen within a certain length of downstream pipe released by the failure of pressure boundaries of various geometric assumption. The results show that local ignition is developed in limited area such as boundary layer and the mixing of hydrogen and air is weak at the planar pressure boundary conditions, whereas the flame fronts at the contact region are developed at the pressure boundaries of the spherical shape.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.99-108
• /
• 2004

In this paper, a small supersonic wind tunnel is designed and built to study the flow characteristics of a supersonic impulse turbine. The flow is visualized by means of a single pass Schlieren system. The supersonic cascade with 2-dimensional supersonic nozzle was tested over a wide range of pressure ratio. Highly complicated flow patterns including shocks, nozzle-cascade interaction and shock boundary layer interactions are observed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.39-44
• /
• 2011

This study constructed the spray distribution by the Tomography method at high pressure condition. The constructed spray distribution was compared with the images by Indirect Photography method so that the spray size was confirmed and took the boundary of the distribution. It was confirmed that the Tomography applies to construct the distribution at high pressure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.12
• /
• pp.18-24
• /
• 2006

Passive control of the shock wave/turbulent boundary-layer interaction utilizing slotted plates and a porous plate over a cavity has been carried out. Effect of various slot configurations on the characteristics of the interaction has been observed. Pitot/wall surface pressure distributions and flow visualizations including Schlieren images, kerosene-lampblack tracings and interference fringe patterns over a thin oil-film have been obtained at the downstream of the shock interactions. For the streamwise-slot configuration, a local higher pitot pressure was noticed at the downstream of the interaction as compared with the case of no control, however, not much improvement in pitot pressure was observed for the spanwise-slot configuration.

• Water for future
• /
• v.21 no.3
• /
• pp.291-291
• /
• 1988

The two dimensional time dependent flow past a circular cylinder is analyzed numerically. In the analysis, equations of conservation of mass and momentum are transformed to equations of stream function-vorticity and vorticity transport, and nondimensionalized by nondimensional parameters representing flow characteristics, The resulting stream function-vorticity equstion and vorticity transport equation are solved by successive over relaxation scheme and alternating direct implicit scheme. Numerical experments are performed for the flow in the range of Reynolds number 125 to 275. The time dependent streamlines, vorticities, pressure on cylinder surface, separation angle, and drag and lift coefficients are calculated, and the method for estimation of pressure on cylinder surface and the outer boundary limit are developed.

• Journal of Energy Engineering
• /
• v.12 no.1
• /
• pp.29-34
• /
• 2003

Thermo-acoustic waves can be generated in a compressible fluid by rapid heating and cooling near the boundary walls. These phenomena are very important mechanism of heat transfer in the space environment in which natural convection does not exist. In this study, the generation and transmission characteristics of thermo-acoustic waves in an air filled enclosure with rapid wall heating are studied numerically. The governing equations were discretized using control volume method, and were solved using PISO algorithm and second-order upwind scheme. For the stable solution time step were considered as t=1$\times$$10^{-9}$ order, and grids are 50$\times$800. The induced thermo-acoustic wave propagates through the fluid until it decays due to viscous and heat dissipation. The wave showed sharp front shape and decreased with long tail.