• Journal of the Korean GEO-environmental Society
• /
• v.20 no.4
• /
• pp.5-9
• /
• 2019

This paper is to provide the results of a pilot study of the usability and possibility of impact force response signal induced from impacting an object for the assessment of compressive strength of various materials (rock, concrete, wood, etc.) nondestructively. For this study, a device was devised for impacting an object and measuring the impact force. The impact was carried out by an initial rotating free falling impact and following repetitive impacts from the rebound action which eventually disappears. Wood and rock test specimens for different strengths were tested and an impact force response signal was measured for each test specimen. The total impact force signal energy which is assessed from integrating the impact force response signal was compared with the directly measured compressive strength for each specimen. The comparison showed that the total impact force signal energy has a direct relationship with the directly measured compressive strength and the results clearly indicated that the compressive strength of construction materials can be assessed nondestructively using total impact force signal energy which is assessed from integrating the impact force response signal induced from impacting an object.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.9
• /
• pp.25-32
• /
• 2023

The Korean Industrial Standards (KS F) have a various regulations for measuring the weight of dried soil and rock. However, if the dried weight is measured in air after drying at 110±5℃ or 105±5℃, a weight singularity occurs, in which the weight decreases and then increases as the measurement time continues. In this study, basaltic rock from Ulleung Island was oven dried at 40 to 110℃. The weight was measured on an electronic scale with a sensitivity of 0.0001g (0.1mg) to find weight singularities. A method to easily determine the dry weight using the weight singularities was presented. As a result of analyses of the singularity of rock specimen according to temperature, the singularities were appeared in the temperature range of 40 to 110℃, and the weight of the singularity was smaller as the heating temperature increased. In particular, the weight singularity duration appeared, and the duration of the singularity was shorter as the heating temperature increased. The results of the convection measurement experiment showed that the cause of the singularity is the convection phenomenon caused by the contact of the heated rock with the air. The weight decrease of oven dried rock occurs when the effect of convection is dominant over the effect of air moisture absorption. Conversely, the weight increase of rock occurs when the effect of air moisture absorption is dominant over the effect of convection.

• Korean Journal of Mineralogy and Petrology
• /
• v.36 no.1
• /
• pp.1-17
• /
• 2023

On painting cultural properties to which Orpiment, a traditional yellow mineral pigment, is applied, the color's degeneration is frequently observed. To identify the cause of the degeneration, this study takes a look into orpiment and the various pigments that are mixed into it (Lead White, Lead Red, and Cinnabar) in powder and painting state. The pigment was mixed with Argyo glue and then applied to korean traditional paper and silk. Considering the possibility that alum causes the discoloration, it was applied to the specimen. With a UV tester, the powders and the painted specimens were subjected to a light resistance test in three phases (96 hour). Color changes were measured with a colorimeter and minerals, chemical composition and structural changes were analysed by XRD, SEM/EDS and Raman spectrometers. While the color change of pure Orpiment powder according to the light resistance test was small, the colored specimen became darker. The color change was large in the Orpiment colored on the silk and in the alum-treated specimen. In Orpiment powder was produced white arsenolite as altered orpiment after UV test. In the mixed powder of Orpiment and Lead White were detected only the constituent minerals of Orpiment and Lead White, and no altered substances were produced. Whereas after the UV test, orpiment and arsenolite, which were altered substances of orpiment, and the constituent minerals of Lead White were detected. In the case of mixing the two pigments in the powder state, darkening did not occur even by the UV test. However, the specimens colored with the mixed powder were darkened by the UV test. The color change of Orpiment was different depending on the mixed pigment and base material. The color change was greater in the case of alum treatment than in the case without alum treatment, and it was found that alum also had an influence on the color change of Orpiment.

• The Journal of Engineering Geology
• /
• v.4 no.3
• /
• pp.269-281
• /
• 1994

Microscopic study and X-ray diffraction analysis were carried out to find out rock type, tock forming minerals; and weathering characteristics of rocks at the constructing site of the churyong Tunnel, Kyongju-Gun, Kyongbuk. Seismic velocity and compressional strength were measured to evaluate mechanical properties of rock. The rock of the study area is Jurassic tuff consisting of clay minerals, crystals of quartz and feldspar, fragments of volcanic rocks and shale. Fresh tuff has compressional strength of about $443kg/\textrm{cm}^2$ and seismic velocity of about 3680m/sec in average. It is classified as soft rock. Rock fragment within tuff is andesite and it has compressional strength of about $2500kg/\textrm{cm}^2$ and seismic velocity of about 4340m/sec in average. It is classified as hard rock. A good linear relationship is found between compressional streangth and seismic velocity in both laboratory sample and in-situ rocks. Laboratory samples has seismic velocities faster about 1.5km/sec than those in-situ rocks. It is interpreted that joints, fractures, and water content in the in-situ rocks result in decreas of seismic velocity. As Tuff has more than 50% of clay minerals in matrix and shale fragments, it absorbs water easily in atmospheric condition. Therefore, though the rock in the study area is medium hard rock before weathering, it is weathered very easily in the case of exposure to natural environment, comparing with other rock.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.10 no.2
• /
• pp.139-152
• /
• 2008

A series of numerical experiments were carried out to simulate the rock cutting behavior by TBM disc cutter in a given took condition. AUTODYN-3D, a commercial program capable of simulating three-dimensional dynamic failure, was utilized to carry out the numerical tests over four different disc cutter spacing conditions. After modelling three-dimensional geometries of disc cutter and rock specimen, the linear cutting tests by a disc cutter were simulated for eight different types of rocks. The numerical result, that is the optimum cutter spacing for isotropic rocks had the good agreements with those from linear cutting test. However, for relatively anisotropic or jointed rocks, the specific energy obtained from the numerical tests was almost two-times bigger than the real linear cutting results. Therefore, to simulate cutting procedures for anisotropic rocks realistically, further studies would be necessary.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.10 no.3
• /
• pp.99-106
• /
• 1990

This study was aimed to see the effect of chemical grout on fresh granite joint shear strength. The grouting chemical used in this study was composed of 25% water glass. Direct shear tests were performed on the chemical filled joints, which had been made artificially with granite. The test results show that chemical grouted rock jonts have markedly reduced shear strength comparing with the ungrouted fresh joints and they sheared within chemical grout before the rock to rock contact had been established, while the ungrouted joint sheared between rock surfaces from the beginning of shear deformation. With chemical grouted joints the shear stress slowly reached its maximum without showing distinct peak shear strength. Therefore the shear stiffness of joints were decreased with increasing thickness of grout. but the shear strain at failure was increased with it.

• Korean Journal of Mineralogy and Petrology
• /
• v.35 no.1
• /
• pp.51-64
• /
• 2022

For effective preservation of the rocks, which bearing plant fossils at Gumkwangdong Formation, Pohang, the properties of rock and treatment of chemicals were examined in an artificial weathering test. The rocks are diatomaceous siliceous mudstone, which contain a small amount of smectite and has developed laminated layers. The rocks react with water, the d₀₀₁ spacing of smectite was increased. On the one hand, the physical properties of the rock samples, such as surface hardness, improved after the application of ethyl silicate-based stone strengthener. On the other hand, the spacing of interlayer of swelling clay minerals decreased and spacing of laminae layer increased. When the ethyl silicate-based stone strengthener was applied after pretreatment with a swelling inhibitor, interlayer and spacing of laminae changes were similar to those when only the stone strengthener was treated. The effect of the swelling inhibitor was almost negligible. When the rocks that have been conserved with chemicals react with water, spacing of laminae has widened much, whereas when the rocks was in contact with moisture only, there was little change. In addition, if it is placed in the outdoor after conservation treatment, although it occurs slightly slower than the untreated rock, the separation of the lamination layer and the pulverization of the rock occur within a very short time. Consolidation is required to improve the physical properties of fossil rock, but when exposed to rain and undergoing freeze-thaw process, the effect is lost very quickly. Therefore, regardless of the chemical treatment, it is a priority to prevent direct rainfall contact with the rock.

• The Journal of Engineering Geology
• /
• v.21 no.4
• /
• pp.323-336
• /
• 2011

The hydro-mechanical behavior of the Earth's crust is strongly dependent on the fractional volume and geometrical structure of effective pore spaces. This study aims to understand the characteristics of pores using electrical impedance. We measured the electric impedance of core samples (diameter, 38-50 mm; length, 70-100 mm) of three types of granite (Hwangdeung, Pocheon, and Yangsan) and two types of sandstone (Boryung and Berea) with different porosities and pore structures, after saturation with saline water of varying salinities. The results show that resistance decreases but capacitance increases with increasing salinity of the pore fluid. For a given salinity, the resistivity and formation factor are reduced with increasing porosity of the rocks, and the capacitance increases. Berea sandstone shows anisotropy in resistance, tortuosity, and cementation factor, with these factors being highest normal to bedding planes. This result indicates that the connectivity of pores is weakest normal to bedding. In conclusion, the electrical characteristics of the tested samples are related not only to their porosity but also to the pore geometry.

• The Journal of Engineering Geology
• /
• v.5 no.3
• /
• pp.237-274
• /
• 1995

This study was focused on the improvement of the measurement technique of P-wave velocity for the assesment of the anisotropy of the engineering property of rock. Samples used were collected from a working quarry within the Carnmenellis granite area on which series of engineering geological data have been accumulated. This study mainly concerned the development of measurement technique at the curved surface of rock, the use of natural honey-based coupling agent and the drying method for rock specimen over $P_2O_5$. According to the results, the range of the P-wave velocity anisotropy in two dimensional plane, fell between 0 and 4.68 (%). The direction where maximum velocity occurred was parallel to the orientation of the maximum in-situ stress. The result showed that P - wave velocity is a useful measure to asses the anisotropy of the engineering property of rock and it is suggested that the improvements adopted here can be applied to the experimental work on the rocks in Korea.

• Journal of Korea Water Resources Association
• /
• v.33 no.2
• /
• pp.237-245
• /
• 2000

Sihwa seadike is originally designed to control the water level In lake Sihwa. However the sluice gate is being operated everyday to preserve the water quality of lake. Due to the frequent operation of gates the bottom of drainage canal which is composed of weathered rock and soft rock is being scoured. Recently the bottom in the front area of apron was protected by putting underwater concrete. This study is carried out to understand the hydraulic situation for protection, and to estimate the trend of scouring by comparing between energy dissipation and registance of bottom rock. Annandale(1995) introduced the erodibility index theory, and suggested a criteria to judge the erodibility of rock through the relation between the erodibility index and energy dissipation. Determenation of erodibility index of rock is based on the results of sample core analysis, and the energy dissipation of flow is calculated from the estimation of total head on the scale model. These two values are plotted on the criteria, and the erodibility of rock is determined.