• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.279-279
• /
• 2011

본 연구는 LED 등기구에서 방열코팅소재에 따른 방열 효과를 연구하여 LED 등기구를 안정적으로 유지 제어 할 수 있는 방법을 찾고자 한다. 그에 따라 동일한 기구물에서 방열코팅만 변화하여 LED chip 온도의 Steady State 온도를 비교 측정하였다. 방열코팅은 동일한 알루미늄 Heat Sink에 일반분체코팅, Anodizing 처리, 알루미나 방열도료, Graphene이 섞인 알루미나도료, Graphene 잉크 등의 방열코팅소재를 아무 처리를 하지 않은 알루미늄 Heat Sink 와 비교 하였다. 온도는 LED chip, LED base plate, 코팅이 된 표면, 코팅 내부 2 mm 부분의 온도를 각각 Steady State가 될 때까지 측정하였다. 또한 LED의 power를 7 watt에서 13 watt 변화하면서 방열 원리를 분석하였다. 본 연구를 통하여 각 코팅소재에 따른 방열효과와 그 방열 원리를 연구 분석하였다.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.3
• /
• pp.136-140
• /
• 2000

A stainless steel separator for a molten carbonate fuel cell is usually coated with aluminum diffusive layer to protect its surface against corrosion by the molten carbonate at high temperatures. In this study, a relatively simple method was devised to form the aluminum diffusive layer on a stainless steel substrate. Slurry coating of aluminum on the substrate followed by heat treatment under reducing atmosphere at $650\~800^{\circ}C$ produced the aluminum diffusive layer of $25\~80{\mu}m$ thickness. The thickness of aluminum diffusive layer increased with increasing the temperature or duration of the heat-treatment. The corrosion resistance against molten carbonate under oxidizing atmosphere was significantly improved by aluminum diffusive layer formed by the sluny painting and heat treatment method. Moreover, the sample prepared in this study showed corrosion behavior similar to the sample with aluminum diffusive layer prepared by ion vapor deposition and heat treatment.

• Journal of Aerospace System Engineering
• /
• v.14 no.3
• /
• pp.51-59
• /
• 2020

In the case of cubesat, a PCB-based deployable solar panel advantageous in terms of weight reduction and electrical circuit design is widely used considering the limited weight and volume of satellites. However, because of the low thermal conductivity of PCB, there is a limit relative to heat dissipation. In this paper, the thermal gap pad is applied to the contact between the PCB-based solar panel and the aluminum stiffener mounted on the outside of the panel. Thus, the heat transfer from the solar cell to the rear side of the panel is facilitated. It maximizes the heat dissipation performance while maintaining the merits of PCB panel, and thus, it is possible to improve the power generation efficiency from reducing the temperature of the solar cell. The effectiveness of the thermal design of the 6U cubesat's deployable solar panel using the thermal gap pad has been verified through on-orbit thermal analysis based on the results, compared with the conventional PCB-based solar panel.

• Journal of the korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.44-50
• /
• 1989

Using modal analysis method this paper examines the dynamic characteristics of composite material closely. Composite material is superior to conventional material in view of mechanical properties. So the laminate of CFRPis compared with ALPlate. As the results, the overall vibration level of CFRP is lower than that of AL Plate and is low when fiber direction is parallel to the fixed point. Also, the natural frequency of CFRP is situated in low frequency than that of AL.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.786-787
• /
• 2008

본 논문에서는 1층 주거지역에 미치는 지하 분전반 모선으로부터 발생하는 극저주파 자기장을 억제하기 위한 연구의 일환으로 지하 분전반을 연구모델로 선정한 후 3차원 전자장 유한요소 해석을 이용하여 누설 자속을 분석하였다. 1층 침실에 미치는 자기장을 억제하기 위해 알루미늄 재질의 차폐판을 도입하여 차폐효과를 확인하였다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.92-95
• /
• 2003

Asymmetric rolling of AA1050 Al alloy sheets was performed to obtain the shear textures for improving the deep drawability and the grain refinement. The effect of roll velocity ratio on the texture and the grain refinement of 50％ asymmetrically rolled sheets was studied. The textures of the asymmetrically rolled sheets after annealing at 400$^{\circ}C$ for 1 h was also investigated.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.906-907
• /
• 2011

본 논문은 3D 타원형 결함을 가진 알루미늄 판에 대하여 와전류 탐상 프로브 중 Impedance, T/R, T/T 프로브를 설계하여 결함에서의 특성을 파악하였다. 특성 파악을 위해 세 가지의 결함에 대하여 프로브 코일 임피던스의 실수, 허수 변화에 따른 와전류 센서의 특성을 비교하였다.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.2243_2244
• /
• 2009

본 논문에서는 알루미늄 재질로 된 방열판과 PCB에 1[W]급 LED 14개를 모듈 방열 설계 하여 COMSOL Multiphysics로 시뮬레이션을 통한 결과, 경계면 온도는 약 $80^{\circ}C$, Max.온도$141^{\circ}C$, Min.온도$20^{\circ}C$까지 변화로 실 제작에 근접한 온도 확인이 가능함을 확인 할 수 있었다.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.137-138
• /
• 2015

본 논문은 알루미늄 재질로 된 방열판을 LED조명기구에 적용해서 열 해석을 한 것으로서, PCB에 25[W]급 LED를 배치하여 COMSOL Multi-physics로 시뮬레이션 하였다. 그 결과 LED와 PCB 경계면의 온도는 $69^{\circ}C$이고, PCB바닥면의 온도는 $28^{\circ}C$로 실제작한 FR-4 재질의 LED Module과 근접한 온도임을 확인 할 수 있었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.4
• /
• pp.853-858
• /
• 2008

The structures of induction heating type pressure rice cooker are consisted of oven. top heater plate and locking ring. Because the pressure is applied to their structures, those should be necessary to do the safety evaluation. In this paper, structure analysis is performed for oven structures by using finite element method and as a results, optimal thickness is achieved. Especially, analysis fur anisotropic layered material is performed because oven is made of both stainless steel and aluminum. And both von Mises and Tsai-Wu failure criterion are applied for safety factor. Parametric method is used in order to get the optimal thickness for oven and top heater plate.