• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.11-18
• /
• 2021

A novel microwave dielectric composite material for ultra-low temperature co-fired ceramics (ULTCC) with (1-x)BaWO₄-xBaV₂O₆ (x=0.54~0.85) composition was prepared by firing a mixture of BaWO₄ and BaV₂O₆. Shrinkage tests showed that the ceramic composite begins to densify at a temperature as low as 550℃ and can be sintered at 650℃ with 98% of relative density under the influence of BaV₂O₆. X-ray diffraction analysis showed that BaWO₄ and BaV₂O₆ coexisted and no secondary phase was detected in the sintered bodies, implying good chemical compatibility between the two phases. Near-zero temperature coefficients of the resonant frequency (𝛕_f) could be achieved by controlling the relative content of the two phases, due to their positive and negative 𝛕_f values, respectively. With increasing BaV₂O₆ (x from 0.53 to 0.85), the 𝛕_f value of the composites increased from -7.54 to 14.49 ppm/℃, ε_r increased from 10.08 to 11.17 and the quality factor (Q×f value) decreased from 47,661 to 37,131 GHz. The best microwave dielectric properties were obtained for x=0.6 samples with ε_r=10.4, Q×f=44,090 GHz, and 𝛕_f=-2.38 ppm/℃. Chemical compatibility experiments showed the developed composites are compatible with aluminum electrode during co-firing process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.341-341
• /
• 2011

최근 AMOLED 구동이 가능한 소자에 대한 연구가 활발히 진행중이다. AMOLED구동 가능소자는 LTPS TFT, a-Si TFT, OTFT, Oxide TFT가 있으며 그 중에서 현재 대부분 LTPS TFT를 사용하고 있다. LTPS TFT는 높은 전자 이동도와 안정성을 가지고 있기 때문에 현재 각광 받는 AMOLED에 잘 맞는다. 하지만 LTPS TFT는 고비용, 250$^{\circ}C$ 이상의 공정온도, Substrate가 Glass, Metal로 제한 된다는 문제점이 있으며, 균일성이 낮고 현재 대면적 기술이 부족한 상태이다. 해결방안으로 AMOLED를 타겟으로 하는 Oxide TFT 기술이 떠오르고 있다. Oxide TFT는 이동도가 높고 저온공정이 가능하며 Substrate로 Plastic 기판을 사용할 수가 있어 차후에 Flexible 소자로서의 적용이 가능하다. 또한 기존의 진공장비 사용대신 용액공정이 가능하여 장비사용시간 및 절차를 단축시킬 수 있어 비용적인 유리함을 가지고 있다. Oxide TFT는 단결정 산화물과 다결정 복합 산화물 두 가지 범주를 가지고 있다. Oxide TFT의 재료물질은 ZnO, ZTO, IZO, SnO2, Ga2O3, IGO, In2O3, ITO, InGaO3(ZnO)5, a-IGZO이 있다. 본 연구에서는 산화물질 중 하나인 ZTO를 이용하여 TFT 소자를 제작하였다. 산화물 특성상 열처리 온도에 따라 형성되는 결정의 정도가 다르기 때문에 온도 및 시간 변수에 따른 ZTO의 특성변화에 초점을 맞추어 연구함으로서 최적화된 조건을 찾고자 실험을 진행하였다. 실험을 위한 기판으로 n-type wafer을 사용하였다. PE-CVD 장비를 이용하여 SiNx를 120 nm 증착하고, ZTO 용액을 spin-coating을 이용하여 channel layer을 형성하였다. 균일하게 형성된 ZTO의 결정을 위하여 200$^{\circ}C$, 300$^{\circ}C$, 400$^{\circ}C$, 500$^{\circ}C$에서 1시간, 3시간, 6시간, 10시간의 온도 및 시간 변수를 두어 공기 중에서 열처리 하였다. ZTO는 약 30 nm 두께로 형성되었다. Thermal evaporator를 이용하여 Source, Drain의 알루미늄 전극을 형성하고, wafer 뒷면에는 Silver paste를 이용하여 Gate전극을 만들었다. 제작된 소자를 dark room temperature에서 측정하였다.

• Journal of Welding and Joining
• /
• v.31 no.2
• /
• pp.26-29
• /
• 2013

The latest research & development trend on friction stir welding and friction stir processing technologies presented in the international symposium, 'Friction Stir Welding & Processing VII'. Papers and presentations about high temperature materials such as advanced high strength steel, stainless steel and titanum alloy shoot up this year. Papers on modeling of metal flow and control of process parameters also increased. The FSP technologies for manufacturing of carbon materials reinforced metal matrix composites were reported, too.

• Magazine of the Korea Concrete Institute
• /
• v.6 no.4
• /
• pp.141-152
• /
• 1994

The results of an experimental study on the development and the evaluation of lightweight and high strength composites utilizing by-products and calcium silicates for construction materials are presented in this paper. The composites using early strength portland cement, by-Products( f1y ash, silica fume), silica powder, quick lime, gypsum, A1 powder and fibers(PAN-derived CF, alkali-resistance GF) were prepared using various mixing conditions. As the test results show, PAN-derived CF and alkali-resistance GF were suitable for rein-forcing fiber of the composites. And the mechanical properties,such as compressive tensile flexural strength, and toughness of Lt. Wt. fiber reinforced calcium silicates cement comp-osites were improved by increasing the fly ash and silica fume contents, and fiber contents, especially by increasing fiber contents the toughness of the composites were remarkably in-creased. Also, compressive tensile flexural strength,and toughness of the composites rein-forcing PAN-derived CF were higher than those of the composites reinforcing alkali-resistance GF..

• Composites Research
• /
• v.32 no.2
• /
• pp.120-126
• /
• 2019

Advanced fiber fabrics have been utilized in not only anti-stabbing and bullet-proofing for body armor but also various industrial fields including vehicular armor and spacecraft structure. Furthermore, there have been a number of research to improve the ballistic performance of advanced fabrics introducing many computational approaches. In our research, an advanced fabric, Heracron manufactured in South Korea was modelled firstly using Autodyn, a commercial software specializing in impact and explosion phenomenon. The sensitivity of the input parameters was also confirmed by conducting simulations. To verify the numerical modelling, we measured and compared the simulation results with velocity decrements after impact involving one, three, and five layers of Heracron under 200-500 m/s impacts by an aluminum spherical projectile. The Heracron fabric was successfully modelled using Autodyn.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.22 no.3
• /
• pp.127-134
• /
• 2016

In this study, Biodegradable masterbatch (M/B) was prepared by different kinds and content of biodegradable catalysts added to oxo biodegradable plastics. The bio film was prepared by adding biodegradable M/B to the polyethylene pellet, and the change of physical properties by UV and heat treatment and the stability as food packaging material were confirmed. As a result of the physical property change, Fe salt and Al salt bio film was superior to Ni salt bio film about a decrease in physical property. However, considering the raw material cost and industrial availability, M/B containing Fe salt was selected and additional experiments were conducted by concentration. The bio films prepared with Fe salt M/B 1.0, 1.5 and 2.0 wt% showed excellent physical properties.

• The Journal of Korean Academy of Prosthodontics
• /
• v.53 no.4
• /
• pp.295-300
• /
• 2015

Purpose: The aim of this study was to evaluate the shear bond strength between Ni-Cr alloy and composite resin using universal adhesive systems coMPared to conventional method using metal primers. Materials and methods: For this study, a total of 120 cast commercial Ni-Cr alloy (Vera Bond 2V) disks were embedded in acrylic resin, and their surfaces were smoothed with silicon carbide papers and airborne-particle abrasion. Specimens of each metal were divided into 6 groups based on the combination of metal primers (Metal primer II, Alloy primer, Metal & Zirconia primer, MKZ primer) and universal adhesive systems (Single Bond Universal, All Bond Universal). All specimens were stored in distilled water at $37^{\circ}C$ for 24 hours. Shear bond strength testing was performed with a universal testing machine at a cross head speed of 1 m/min. Data (MPa) were analyzed using one-way ANOVA and the post hoc Tukey's multiple comparison test (${\alpha}$=.05). Results: There were significant differences between Single Bond Universal, All Bond Universal, Metal Primer II and Alloy Primer, MKZ Primer, Metal & Zirconia Primer (P<.001). Conclusion: Universal Adhesive system groups indicated high shear bond strength value bonded to Ni-Cr alloy than that of conventional system groups using primers except Metal Primer II. Within the limitations of this study, improvement of universal adhesive systems which can be applied to all types of restorations is recommended especially non-precious metal alloy. More research is needed to evaluate the effect of silane inclusion or exclusion in universal adhesive systems.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.4
• /
• pp.63-73
• /
• 2009

Recently, the use of lightweight panels in building structures has been increasing. Of the various lightweight panel types, styrofoam sandwich panels are inexpensive and are excellent in terms of their insulation capacity and their constructability. However, sandwich panels that include organic material are quite vulnerable to fire, and thus can numerous casualties in the event of a fire due to the lack of time to vacate and their emission of poisonous gas. On the other hand, lightweight foamed concrete is excellent, both in terms of its insulation ability and its fire resistance, due to its Inner pores. The properties of lightweight concrete is influenced by foaming agent type. Accordingly, this study investigates the insulation properties by foaming agent type, to evaluate the possibility of using light-weight foamed concrete instead of styrene foam. Our research found thatnon-heating zone temperature of lightweight foamed concrete using AP (Aluminum Powder) and FP (animal protein foaming agent) are lower than that of light-weight foamed concrete using AES (alkyl ether lactic acid ester). Lightweight foamed concrete using AES and FP satisfied fire performance requirements of two hours at a foam ratio 50, 100. Lightweight foamed concrete using AP satisfied fire performance requirements of two hours at AP ratio 0.1, 0.15. The insulation properties were better in closed pore foamed concrete by made AP, FP than with open pore foamed concrete made using AES.