• Journal of Food Hygiene and Safety
• /
• v.27 no.4
• /
• pp.420-426
• /
• 2012

The purpose of this study was to identify control points through microbiological hazard analysis in the manufacturing processes of starch noodles. Samples were collected from the ingredients, manufacturing processes, equipment and environment. Microbiological hazard assessments were performed using aerobic plate counts (APC), Enterobacteriaceae (EB), E. coli and five pathogens including B. cereus, E. coli O157:H7, L. monocytogenes, Salmonella spp., and S. aureus. The APC levels in raw materials were from 2.12 to 3.83 log CFU/g. The contamination levels after kneading were 4.31 log CFU/g for APCs and 2.88 log CFU/g for EB counts. APCs decreased to 1.63 log CFU/g and EB were not detected after gelatinization, but their levels slightly increased upon cooling, cutting, ripening, freezing, thawing, and separating. The reuse of cooling and coating water would be a critical source of microbial increase after cooling. After drying, APCs and EB counts decreased to 5.05 log CFU/g and 2.74 log CFU/g, respectively, and the levels were maintained to final products. These results suggest that the cooling process is a critical control point for microbiological safety, and the cooling water should be treated and controlled to prevent cross contamination by pre-requisite program.

• Journal of Food Hygiene and Safety
• /
• v.29 no.2
• /
• pp.99-104
• /
• 2014

This study was done to analyze the contents of minerals and to investigate the ratio of measured values to labeled values and to analyze the ratio of calcium to other minerals in 68 specimen with minerals - fortified commercial beverages, noodles, cereals and grain products. Content of calcium, iron and zinc in samples after microwave digestion was analyzed with an ICP-OES. The measured values of calcium were ranged 82.2~293.1% of the labeled values in 38 samples composed calcium - fortified commercial beverages, noodles, cereals and grain products. The measured values of iron and zinc were ranged 83.3~301.0%, 90.1~314.1% of the labeled values in minerals - fortified commercial beverages, noodles, cereals and grain products, 42, 24 samples. The Ca : Fe ratios were 90.55 (50.55~220.64) in fruit & vegetable juice, 850.41 in fruit & vegetable beverage, 553.49 in blended beverage, 179.07 (118.37~238.01) in soy milk, 204.39(41.64~397.52) in noodle, 296.97(121.64~868.88) in fried noodle, 30.89(15.69~62.05) in cereal and 7.73(0.22~49.92) in grain product. The Ca : P ratios were 1.44(0.96~1.98) in fruit & vegetable juice, 1.92 in fruit & vegetable beverage, 1.66 in blended beverage, 4.23(2.25~7.72) in soy milk, 1.14(0.28~1.97) in noodle, 1.88(1.17~2.42) in fried noodle, 1.29(0.87~2.92) in cereal and 0.30(0.06~1.57) in grain product. The Ca : Mg ratios were 1.85(0.87~5.04) in fruit & vegetable juice, 28.72 in fruit & vegetable beverage, 2.97 in blended beverage, 5.27(2.93~9.36) in soy milk, 3.97(1.34~7.57) in noodle, 6.77(4.63~10.78) in fried noodle, 4.40(2.30~12.55) in cereal and 1.17(0.23~7.48) in grain product. These results suggest calcium contents and the ratio of calcium contents to other minerals in calcium-fortified food products should be strictly controlled. Moreover, to avoid problems with Excessive nutrition, there must be initiatives for better understanding on food labelling and nutrition for fortified food.

• Journal of Food Hygiene and Safety
• /
• v.36 no.5
• /
• pp.447-453
• /
• 2021

In this study, the effectiveness of physical control technology, a combined light sterilization (LED, UV) and hot water treatment in reducing Aspergillus ochraceus for food production environment was investigated. In brief, 1 mL aliquot of A. ochraceus spore suspension (10^7-8 spore/mL) was inoculated onto stainless steel chips, which was then dried at 37℃, and each was subjected to different physical treatment. Treatments were performed for 0.5, 1, 2, 5, 8, and 11 hours to reduce the strains using a light-emitting diode, but no significant difference was confirmed among the treatments. However, a significant reduction was observed on the chips treated with UV-C exposure and hot water immersion. After being treated solely with 360 kJ/m² of UV-C on stainless steel chip, the fungi were significantly reduced to 1.27 log CFU/cm². Concerning the hot water treatment, the initial inoculum amount of 6.49 log CFU/cm² was entirely killed by immersion in 83℃ water for 5 minutes. Maintaining a high temperature for 5 minutes at the site is difficult. Thus, considering economic feasibility and usability, we attempted to confirm the appropriate A. ochraceus reduction conditions by combining a relatively low temperature of 60℃ and UV rays. With the combined treatments, even in lukewarm water, A. ochraceus decreased significantly through the increases in the immersion time and the amount of UV-C irradiation, and the yield was below the detection limit. Based on these results, if work tools are immersed in 60℃ lukewarm water for 3 minutes and then placed in a UV sterilization device for more than 10 minutes, the possibility of A. ochraceus cross-contamination during work is expected to be reduced.

• The Korean Journal of Air & Space Law and Policy
• /
• v.33 no.2
• /
• pp.61-114
• /
• 2018

Recently airspace became a hot issue considering today's international relations. However, there was no data that could be fully explained about a legal system of korean airspace, so I looked at law and practice about korean airspace together. The nation's aviation law sector is comletely separate from those related to civil and military aircraft, at least in legal terms. The Minister of Land, Infrastructure and Transport shall carry out his/her duties with various authority granted by the "Aviation Safety Act". The nation's aviation-related content is being regulated too much by the Ministry of Land, Infrastructure and Transport's notice or regulation, and there are many things that are not well known about which clauses of the upper law are associated with. The notice should be clearly described only in detail on delegated matters. As for the airspace system, the airspace system is too complex for the public to understand, and there seems to be a gap between law and practice. Therefore, I think it would be good to reestablish a simple and practical airspace system. Airspace and aviation related tasks in the military need to be clearly understood by distinguishing between those entrusted by the Minister of Land, Infrastructure and Transport and those inherent in the military. Regarding matters entrusted by the Minister of Land, Infrastructure and Transpor, it is necessary to work closely with the Minister of Land, Infrastructure and Transport when preparing related work guidelines, and to clarify who should prepare the guidelines. Regarding airspace control as a military operation, policies or guidelines that are faithful to military doctrine on airspace control are needed.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.47 no.5
• /
• pp.41-48
• /
• 2019

Our daily lives are changing at a rapid pace and the concept of smart city is spreading, as the information communication technologies apply to various fields. However, efforts to prepare for changes in society due to technological evolution are insufficient in the field of landscape architecture. The purposes of this study are to explore the concept of smart parks, to investigate how smart technology has been applied to parks, and to identify the users' perception and satisfaction on smart park services. To this end, we conducted literature review, focus group interviews with experts, and a questionnaire survey with 180 users of the IoT See pilot smart park in Daegu. Smart parks can, as a result, be defined as sustainable parks that improve users' experience in parks and solve social and environmental problems faced by utilizing various high technology. Smart technologies introduced at the park so far have been mostly focused on safety and environmental areas, including AI CCTV, smart street lamp, and fine dust warning devices. The results of survey showed that not many users were aware of the smart services the park provided due to the lack of public communication as well as the nature of maintenance-oriented smart services. The survey also found that AR services for the education of historic parks were the least utilized, while solar power benches and WiFi service were most preferred by the park users. In conclusion, smart technologies need to be integrated with diverse park contents more centered user needs, providing services to enhance safety and environmental management in order to develop user-oriented smart parks.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.18 no.5
• /
• pp.3-16
• /
• 2008

A Wireless Sensor Network (WSN for short) is a wireless network consisting of distributed small devices which are called sensor nodes or motes. Recently, there has been an extensive research on WSN and also on its security. For secure storage and secure transmission of the sensed information, sensor nodes should be equipped with cryptographic algorithms. Moreover, these algorithms should be efficiently implemented since sensor nodes are highly resource-constrained devices. There are already some existing algorithms applicable to sensor nodes, including public key ciphers such as TinyECC and standard block ciphers such as AES. Stream ciphers, however, are still to be analyzed, since they were only recently standardized in the eSTREAM project. In this paper, we implement over the MicaZ platform nine software-based stream ciphers out of the ten in the second and final phases of the eSTREAM project, and we evaluate their performance. Especially, we apply several optimization techniques to six ciphers including SOSEMANUK, Salsa20 and Rabbit, which have survived after the final phase of the eSTREAM project. We also present the implementation results of hardware-oriented stream ciphers and AES-CFB fur reference. According to our experiment, the encryption speeds of these software-based stream ciphers are in the range of 31-406Kbps, thus most of these ciphers are fairly acceptable fur sensor nodes. In particular, the survivors, SOSEMANUK, Salsa20 and Rabbit, show the throughputs of 406Kbps, 176Kbps and 121Kbps using 70KB, 14KB and 22KB of ROM and 2811B, 799B and 755B of RAM, respectively. From the viewpoint of encryption speed, the performances of these ciphers are much better than that of the software-based AES, which shows the speed of 106Kbps.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.7
• /
• pp.1209-1215
• /
• 2022

The selective catalytic reduction (SCR) is known as a very efficient method to reduce nitrogen oxides (NOx) and the catalyst performs reduction from nitrogen oxides (NOx) to nitrogen (N₂) and water vapor (H2O). The catalyst, which is one of the factors determining the performance of the nitrogen oxide (NOx) ruduction method, is known to increase catalyst efficiency as cell density increases. In this study, the reduction characteristics of nitrogen oxides (NOx) under various engine loads investigated. A 100CPSI(60Cell) catalysts was studied through a laboratory-sized simulating device that can simulate the exhaust gas conditions from the power generation engine installed in the training ship SEGERO. The effect of 100CPSI(60Cell) cell density was compared with that of 25.8CPSI(30Cell) cell density that already had NOx reduction data from the SCR manufacturing. The experimental catalysts were honeycomb type and its compositions and materials of V₂O₅-WO₃-TiO₂ were retained, with only change on cell density. As a result, the NOx concentration reduction rate from 100CPSI(60Cell) catalyst was 88.5%, and IMO specific NOx emission was 0.99g/kwh satisfying the IMO Tier III NOx emission requirement. The NOx concentration reduction rate from 25.8CPSI(30Cell) was 78%, and IMO specific NOx emission was 2.00g/kwh. Comparing the NOx concentration reduction rate and emission of 100CPSI(60Cell) and 25.8CPSI(30Cell) catalysts, notably, the NOx concentration reduction rate of 100CPSI(60Cell) catalyst was 10.5% higher and its IMO specific NOx emission was about twice less than that of the 25.8CPSI(30Cell) catalysts. Therefore, an efficient NOx reduction effect can be expected by increasing the cell density of catalysts. In other words, effects to production cost reduction, efficient arrangement of engine room and cargo space can be estimated from the reduced catalyst volume.

• Journal of Service Research and Studies
• /
• v.13 no.1
• /
• pp.186-200
• /
• 2023

This study aims to improve the usability of the white cane, which is walking equipment that most local visually impaired people use and carry when going out, and to contribute to the prevention of safety accidents and the walking rights of visually impaired people by providing improvement and resolution measures for the problems identified. Also, this study is a study on the visually impaired, primarily targeting the 1st to 2nd degree visually impaired people, who cannot go out on their own without walking equipment such as a white cane, corresponding to 20% among approximately 250,000 blind and low vision people in the Korean population. In the study process, the concept has been developed from the user's point of view in order that the white cane becomes a real help in the walking step of the visually impaired and the improvement of usability of the white cane, the main walking equipment for the visually impaired, are done by problem identification through the Double Diamond Model of Design Thinking (Empathize → Define → Ideate → Prototype → Test (verify)). As a result of the investigation in the process of Empathy, a total of five issues was synthesized, including an increase in the proportion of the visually impaired people, an insufficient workforce situation to help all the visually impaired, an improvement and advancement of assistive devices essential for the visually impaired, problems of damage, illegal occupation, demolition, maintenance about braille blocks, making braille block paradigms for the visually impaired and for everyone. In Ideate and Prototype steps, situations derived from brainstorming were grouped and the relationship were made through the KJ method, and specific situations and major causes were organized to establish the direction of the concept. The derived solutions and major functions are defined in four categories, and representative situations requiring solutions and major functions are organized into two user scenarios. Ideas were visualized by arranging the virtual Persona and Customer Journey Map according to the situation and producing a prototype through 3D modeling. Finally, in the evaluation, the final concept derived is a device such a smart cane for guidance for the visually impaired as ① a smart cane emphasizing portability + ② compatibility with other electronic devices + ③ a product with safety and convenience.

• Journal of the Korean Society of Radiology
• /
• v.18 no.3
• /
• pp.293-300
• /
• 2024

On October 31, 2023, the revision of the Medical Technologist Act made it mandatory to complete field training courses in order to obtain a license as a radiologic technologist. Therefore, we would like to survey the actual situation of field training in medical institutions to inform the revised Medical Technologist Act and propose improvement measures to increase the effectiveness of field training. A survey was conducted from March to April, 2023, among radiologic technologists working in medical institutions. The questionnaire was sent through a form on a domestic portal site, Company N, and 120 respondents completed it. Eighty-two respondents, or 68.3 percent, had experience in educating on-the-job training students. 58% of the respondents were aware of the fact that the amendment to the Act on Medical Technologist etc. made field training mandatory to obtain a radiologic technologist license. In accordance with Article 9 of the Medical Technologist Act, which prohibits unlicensed persons from practicing, 50% of the respondents were aware that those who are in training to complete an education course equivalent to the license they are seeking to obtain at a university or other institution are allowed to practice as medical Technologists. When asked what is currently taught during fieldwork, 6% of respondents said that they are required to perform radiation-generating activities in addition to observing, guiding patients, and positioning and moving patients. When asked about the future direction of education as fieldwork becomes mandatory for licensure, 77% of respondents said that they will teach more than they currently do. When asked about the appropriate total length of fieldwork, 35% said 12 weeks and 480 hours, 33% said 8 weeks and 320 hours, and 27% said 16 weeks and 640 hours. It can be seen that the current on-the-job training is inadequate according to various regulations, and students' satisfaction is low. However, with the revision of the Act on Medical Technologists, field training has become mandatory to obtain a license as a radiologist, and it is necessary to improve the educational conditions of field training. Therefore, it is necessary to comply with the Nuclear Safety Act and the Rules on the Safety Management of Diagnostic Radiation Generating Devices, introduce standardized training objectives and evaluation systems, designate training hospitals and radiologists in charge of training, and introduce extended training periods and simulation exercises to internalize field training.

• KDI Journal of Economic Policy
• /
• v.12 no.3
• /
• pp.71-94
• /
• 1990

This paper reviews the rationale of monetary and banking intervention by an outside authority, either the government or the central bank, and seeks to delineate clearly the optimal limits to the monetary and banking deregulation currently underway in Korea as well as on a global scale. Furthermore, this paper seeks to establish an objective and balanced view on the role of the central bank, especially in light of the current discussion on the restructuring of Korea's central bank, which has been severely contaminated by interest-group politics. The discussion begins with the recognition that the modern free banking school and the new monetary economics are becoming formidable challenges to the traditional role of the government or the central bank in the monetary and banking sector. The paper reviews six arguments that have traditionally been presented to support intervention: (1) the possibility of an over-issue of bank notes under free banking instead of central banking; (2) externalities in and the public good nature of the use of money; (3) economies of scale and natural monopoly in producing money; (4) the need for macro stabilization policy due to the instability of the real sector; (5) the external effects of bank failure due to the inherent instability of the existing banking system; and (6) protection for small banknote users and depositors. Based on an analysis of the above arguments, the paper speculates on the optimal role of the government or central bank in the monetary and banking system and the optimal degree of monetary and banking deregulation. By contrast to the arguments for free banking or laissez-faire monetary systems, which become fashionable in recent years, monopoly and intervention by the government or central bank in the outside money system can be both necessary and optimal. In this case, of course, an over-issue of fiat money may be possible due to political considerations, but this issue is beyond the scope of this paper. On the other hand, the issue of inside monies based on outside money could indeed be provided for optimally under market competition by private institutions. A competitive system in issuing inside monies would help realize, to the maxim urn extent possible, external economies generated by using a single outside money. According to this reasoning, free banking activities will prevail in the inside money system, while a government monopoly will prevail in the outside money system. This speculation, then, also implies that the monetary and banking deregulation currently underway should and most likely will be limited to the inside money system, which could be liberalized to the fullest degree. It is also implied that it will be impractical to deregulate the outside money system and to allow market competition to provide outside money, in accordance with the arguments of the free banking school and the new monetary economics. Furthermore, the role of the government or central bank in this new environment will not be significantly different from their current roles. As far as the supply of fiat money continues to be monopolized by the government, the control of the supply of base money and such related responsibilities as monetary policy (argument(4)) and the lender of the last resort (argument (5)) will naturally be assigned to the outside money supplier. However, a mechanism for controlling an over-issue of fiat money by a monopolistic supplier will definitely be called for (argument(1)). A monetary policy based on a certain policy rule could be one possibility. More importantly, the deregulation of the inside money system would further increase the systemic risk inherent in the current fractional banking system, while enhancing the efficiency of the system (argument (5)). In this context, the role of the lender of the last resort would again become an instrument of paramount importance in alleviating liquidity crises in the early stages, thereby disallowing the possibility of a widespread bank run. Similarly, prudential banking supervision would also help maintain the safety and soundness of the fully deregulated banking system. These functions would also help protect depositors from losses due to bank failures (argument (6)). Finally, these speculations suggest that government or central bank authorities have probably been too conservative on the issue of the deregulation of the financial system, beyond the caution necessary to preserve system safety. Rather, only the fullest deregulation of the inside money system seems to guarantee the maximum enjoyment of external economies in the single outside money system.