• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.3-3
• /
• 2009

선박의 건조과정에서 필수적으로 선체 외판에는 선박의 안전과 운항 및 정비 등에 필요한 정보를 나타내기 위해 다양한 종류의 마크 및 문자가 마킹되어진다. 하지만, 단순한 도장 작업만으로는 해상과 같은 부식 환경에서 마크 및 문자가 쉽게 지워지거나 손상되기 때문에 마크 및 문자를 용접 비드(welding bead)로 표시하거나 미리 절단된 강판(steel plate)을 수동으로 용접한 뒤 도장을 함으로써 마크 및 문자의 손상을 방지하고 있다. 이러한 문자마킹작업을 하기 위해서는 작업자가 수작업으로 기준선과 마크 및 문자의 위치를 먹줄 등을 이용하여 마킹을 하고, 해당 마크 및 문자의 템플렛(template)을 이용하여 펀칭을 실시한 후 수동으로 용접을 실시한다. 하지만, 수작업을 통한 선체외판 문자마킹 작업은 작업자의 기량에 따라 품질이 상이하여 품질 저하의 원인이 된다. 또한 대조립 및 탑재 단계에서 문자 마킹 작업시 수직자세의 용접을 요구함으로써 작업자가 안전사고에 노출되어 있으며, 선박의 각 단계별 주요 공정보다 작업시간이 길어져 전체 선박 건조공정을 지연시키는 문제점 등을 야기시킬 수 있다. 이러한 문제점들을 해결하기 위해 조선업계에서는 선체 외판의 마크 및 문자를 자동으로 용접할 수 있는 장치를 개발하기 위해 노력해왔으며, 몇몇 개발 사례가 보고되고 있다. 하지만, 그 실효성 부분에서는 아직까지 해결하지 못한 문제점들로 인해 현장 적용에는 어려움을 보이고 있다. 본 연구에서는 선박외판 문자 자동용접장치의 기능성뿐만 아니라 현업 적용성을 가장 우선적으로 고려하여 문자마킹장치(Marking Robot for Shipbuilding) 개발을 진행하였다. 우선, 적절한 용접 재료를 선정하기 위해서 솔리드 와이어(Solid Wire)와 플럭스 코어드 와이어(Flux Cored Wire)에 대한 비드온 용접(Bead-On Welding)을 아래보기자세와 수직자세에 대해서 실시하여 적절한 용접 조건을 설정하였다. 본 연구에서 개발된 문자마킹 자동용접장치는 3축으로 구성되어 있으며 각 축들을 분리할 수 있도록 개발하여 이동성을 향상시켰으며, 작업면과 용접토치간의 거리를 일정하게 유지시킬 수 있도록 용접전류 센서(Welding Current Sensor)를 이용하여 토치 높이(Wire Extension)를 제어함으로써 균일한 품질의 용접비드를 얻을 수 있었다. 또한 문자마킹 자동용접장치는 본체 구동부와 제어부(Touch Screen)가 쉽게 분리되고 장착이 가능한 구조로 개발되었으며, 용접시 각 용접자세별로 용접전압, 전류 그리고 용접속도 설정이 가능하여 아래보기 자세뿐만 아니라 어떠한 자세에서도 같은 모양의 비드형상을 가지는 문자마킹용접이 가능하도록 개발하였으며, 이는 실험과 현장적용을 통해 검증하였다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.2
• /
• pp.267-274
• /
• 2018

A variety of appendages are attached to coastal and offshore fishing boats to improve stability during navigation or fishing operations (stability performance and roll reduction). These appendages are generally classified into three types, which are shown in Fig. 1. The numerical calculations were conducted for the following eight cases: one case of a bare hull, three cases where a single appendage attached, three cases of a pair of appendages attached, and one case where all three appendages were attached. Table 1 presents the main dimensions of the bare hull and Table 2 describes the main dimensions of the three appendages. The fluid dynamic performance with regard to the three hull appendages was evaluated via CFD for the following cases: each of the appendages attached independently, a pair of appendages attached, and all three appendages attached simultaneously. The No. 1 appendage showed that pressure resistance was proportionally greater than friction resistances. Both Nos. 2 and 3 appendages showed comparable levels of pressure and friction resistances. The correlation between appendages was minimal in the case of pairs and Comparing the cases of the No. 2 appendage attached and all appendages attached, at 11 kn, the EHP showed an difference of 9 %.

• The Korean Journal of Air & Space Law and Policy
• /
• v.28 no.2
• /
• pp.145-181
• /
• 2013

General aviation is an integral part of civil aviation and involves the widest range of aviation segments except commercial aviation. Featured with different operational procedures and practices to satisfy the economic needs and safety requirements of a sovereign state, general aviation tends to be regulated by an individual state. The last three decades have seen exponential growth of commercial air transport in China, but its general aviation sector has remained disproportionally underdeveloped. With the deepening of the reform of low-altitude airspace, the sector is poised for a radical change and rapid growth. However, legislation governing general aviation activities in China is distorted causing inconsistency and confusions in their application and implementation. This paper aims to analyse China's prevailing legislation regulating general aviation activities. It first discusses the various definitions adopted by ICAO and its member states and reviews the development of general aviation in the US, EU, Australia and China. It then examines the sources of China's general aviation laws, e.g. Chicago Convention and its annexes, and Chinese domestic legislature which covers legislation, laws, directives, rules and procedures. The paper continues to analyse and establish the deficiencies of its prevailing legal framework by pointing out the following: variation of definitions in different regulations, inconsistency of principles in existing laws and regulations, legal vacuum concerning government subsidy, environment protection, safety and security, and other operational areas such as aerial club, sightseeing, and search and rescue. In this process, the paper argues that a coherent, consistent and systematic legal framework is required in order to ensure fair competition and safety for a healthy, progressive and sustainable general aviation growth. Suggestions for rectification and improvement are proposed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.6
• /
• pp.1310-1316
• /
• 2014

The IMO has recommended on VHF digital communications operation for sailing ships from 2017. And ships more than 5 tons is obliged to digital communications by fishing Vessels Act and Vessel Safety Act in domestic. The owner of all vessel is equipped to the automatic position reporting device in accordance with the Notice of the Ministry of Oceans and Fisheries to regulations, It shall be ensure to navigations safety and in order to respond quickly in the event of maritime accidents on all vessels. The info-communications station of fishery is operating the automatic position reporting system using the VHF DSC in east sea from 2012, Continuously, which is underway the install plan in south sea and yellow sea. But this plan is very difficult, because of propagation environment is poor on account of complicated coastline and many islands. This paper has analyzed the propagation coverage for position setting of coast station in south sea and the traffic zone set up by compare with RSSI and methode of navigation tracking by VMS.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.4
• /
• pp.443-450
• /
• 2014

In this study, we have discussed about the effect of hydrofoil arrangement and longitudinal moment characteristic on longitudinal motion stability of fully-submerged hydrofoil by the experiment of tandem hydrofoil model. First of all, tandem hydrofoil model that has canard wing arrangement has been made and characteristics of lift force and drag force by performing the lift force and drag force measuring experiment has also been estimated. Besides, tandem hydrofoil model's wing arrangement which has the initial stability and self stability of longitudinal motion has also been determined. In longitudinal stability experiment of tandem hydrofoil model, the motion characteristic of pitch and heave and the longitudinal stability of foil borne condition by variation of self stability of longitudinal moment and longitudinal distance are estimated. The result from the experiment and it's important conclusion can be described as below; Increase the self stability for longitudinal moment, the higher self stability for pitch motions in a constant pitch angles. By increasing the self stability for longitudinal moment, the range of fluctuation of pitch motion and heave motion for pitch angle also will change relatively small and longitudinal stability is excellent. Lastly, when the lift force of hydrofoil is remain constants, we can conclude that securing the enough self stability for longitudinal moment is essential for stable foil borne condition of tandem hydrofoil.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.4
• /
• pp.412-418
• /
• 2014

In this paper, for better boarding performance and pleasant boarding sensitivity of the ship, comparison and analysis was performed of motion sickness questionnaire with MSI(Motion Sickness Incidence) calculation based on ship motion theory(Strip Method) due to sea condition, incident angle in main sail way, economic speed, and calculation position of the training ship Kaya of Pukyong National University. On theses works, the rougher sea conditions became, the higher total motion sickness rate was occurred. The weights of vertical acceleration and the rates of MSI were higher at the bridge and the accommodation, which were located farther from the center of gravity of the ship. And effects of the vertical acceleration of the ship were increased in rolling then in head sea. In comparison between motion sickness questionnaire with MSI calculation, when the vertical acceleration increased, the motion sickness rate increased. The location to increase vertical acceleration and the location to cause motion sickness were agreed.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.5
• /
• pp.543-551
• /
• 2014

This study has searched to find a program in order to manage simply and practically use the expelled AtoN database from the AtoN Simulator and to support the idea decision for the AtoN placement. It examines a program that manages AtoN database through the hierarchy structure, history card and endowment with condition same as a scenario. And accomplishes this study's goal owing to realizing AtoN operational software that helps for visual, hearing sense, fixed amount verification upon AtoN placement project. The AtoN operational software contributes not only flexible control like a newly establishment, relocation etc, but also supports idea decision for AtoN placement plan through many functions such as condition search, virtual sailing and fixed amount appraisal result exhibition, etc. Through utilization of this, it is to help upon the presupposition of the impact to ship or sailor about many designs and in addition, upon the judgment of whether or not for the efficiency and appropriation of the design. It is expected to reduce possible failure costs and management costs due to AtoN design and placement plans, because to compare more various designs thru the easier verification method.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.7
• /
• pp.945-952
• /
• 2019

The International Maritime Organization (IMO) adopted the International Convention on the Control of Ships' Air Pollutants and Discharge as it became interested in environmental issues such as global warming and air pollution. In addition, a special bill on the improvement of air quality, including in port areas, has recently been enacted in Korea to reduce the amount of fine dust generated. As part of such fine dust reduction measures, feasibility studies have been underway on converting diesel engines into battery electric propulsion systems that do not cause fine dust and emissions. Since the battery electric propulsion system can easily utilize renewable energy sources, and does not generate exhaust gas due to combustion of fuel, small coastal ferries with battery electric propulsion systems that use renewable energy have been operating in Europe and the U.S. for several years. However, they have not been introduced in Korea. Therefore, in this study, we selected small coastal ferries in Korea as target ferries, and performed simulations to study the applicability of electric propulsion with batteries linked to solar power systems. Based on the results, we want to confirm the applicability of battery electric propulsion.

• Journal of Navigation and Port Research
• /
• v.44 no.3
• /
• pp.145-150
• /
• 2020

The ship motion of large LNG ships affects ships' safety. The purpose of this study was to estimate the transfer function of roll motion among the hull motion of 153,000 m3 class LNG vessels. The ship motion transfer function was modeled using a Linear Time-Invarient system with single input, single output, and transfer function. The transfer function of the ship motion was estimated by the system identification method using single ocean wave as input of the model, and using the roll motion of the LNG ship obtained through ANSYS as the output of the model. The usefulness of the experimental results was evaluated using the precision and estimation rate of the model for cases wherein the different transfer function dimensions. Results of the experiment showed a precision at 99% and 98%, with estimation rate at 78% and 50%. From these results, we found the proposed method of estimating the transfer function of ship motion in this study reasonable. In the future, data of ship motion in actual sea conditions will be acquired and it will be applied to make the construction of models with multiple inputs and multiple outputs for practical use.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.6
• /
• pp.652-660
• /
• 2017

Recently, the number of tourists using cruise ships in Korea is increasing. and an big cruise ship with an gross tonnage of 160,000 tons or more has entered the domestic ports. Therefore, the government has been making a lot of efforts to confirm the cruise infrastructure for revitalization of the domestic cruise industry. However, there are no standards for cruise ship specifications and water facilities in the domestic port and fishery design standards. Currently, construction of dedicated cruise facilities is under way in major domestic ports. However, due to lack of specifications and domestic standards for cruise ships, it is difficult to design and license special facilities. Therefore, in this study, PIANC rule and domestic harbor and designing standard of fishing port were compared and analyzed in order to present the standard specification of cruise ships. And analyzed the representative linearity of cruises currently being operated. As a result of the ship characteristics analysis, There was a difference in coastal passenger ship in specifications and ship maneuverability. Therefore, in order to design facilities dedicated to cruising, the specifications of the target ship must be included in the domestic design standard. In addition, in order to calculate the scope of the target ship, I applied the coverage rate of 75% to the average specification value of the cruise ship and presented the standards of the cruise ship and the standard of the water area facilities.