• Journal of the Korea Concrete Institute
• /
• v.21 no.6
• /
• pp.745-752
• /
• 2009

This paper presents the optimized mixing design of lightweight aerated concrete using hydrogen peroxide. Design of experiments in order to the optimized mixing design was applied and commercial program (MINITAB) was used. Statistical analysis was used to Box-Behnken (B-B) method in response surface analysis. The influencing factors of experimental are unit cement content, water ratio and hydrogen peroxide ratio. According to the analysis of variance, at the hardened state, water ratio and hydrogen peroxide ratio affects on dried density, compressive strength and bending strength of lightweight aerated concrete, but unit cement content affects on only dried density. In the results of response surface analysis, to obtain goal performance, the optimized mixing design for lightweight aerated concrete using hydrogen peroxide were unit cement content of 800 kg/$m^3$, water ratio of 44.33% and hydrogen peroxide ratio of 10%.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.1
• /
• pp.109-114
• /
• 2010

In this paper, the implementation of a human signal sensing module that has capabilities to check and restore the weak signals from the human body is presented. A module presented in this paper consists of processing and sensing elements related to human pulse and body temperature and a controller implemented with SoC design method. PPG data is detected by a noise filtering process toward the amplified signal which is from the operating frequency between 0.1Hz - 10Hz. A digital temperature sensor is used to check the body temperature. A sensor outputs the corresponding value of the electric voltage according to the body temperature. Moreover, this paper discusses the implementation of an enhanced microprocessor which is synthesized with VHDL as a part of the SoC development and used to control the entire module. The SoC processor is implemented on a Xilinx Spartan 3 XC3S1000 device and has the achieved operating frequency of 10MHz. The implemented SoC processor core is successfully tested with macro memories in FPGA and the experimental results are hereby shown.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.575-582
• /
• 2011

A cleaning blade is an attachment installed in the toner cartridge of a laser printer for removing the residual toner from an organic photo-conductive drum. There have been many studies on the performance and life of the rubber blade. We focus on optimally designing the blade shape parameters to minimize the maximum stress of the blade while satisfying design constraints on the cleaning performance and part interference. The blade is optimally designed using a design of experiments, meta-models and an optimization algorithm implemented in PIAnO (process integration, automation, and optimization), a commercial PIDO (process integration and design optimization) tool. We integrate the CAE tools necessary for the structural analysis of the cleaning blade, automate the analysis procedure, and optimize the solution using PIAnO. We decreased the maximum stress by 32.6% in comparison with that of the initial design.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.5
• /
• pp.501-507
• /
• 2009

By using topology and shape optimization, a theoretically optimum FRP deck was proposed. Firstly, a topologically optimal shape, truss-like structure without hinges, was found. A truss-shape frame is the most ideal structure when subjected to a concentrated force at the center of simply supported beam. An armature was found at the point joining horizontal chord and diagonal chord, which was used as a new design variable. Secondly, optimum value of each variable was decided through shape optimization using genetic algorithm. To compare it with existing commercial FRP decks, shape optimization was performed by fixing the height of FRP decks. To verify the performance of the FRP deck proposed in this study, a finite element analysis was performed. As a result, it satisfies serviceability and safety guide lines of FRP decks.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.307-311
• /
• 2012

In this paper, a novel particle swarm optimization method based on IE3D is used to design a mobile communication Microstrip Patch Antenna. The aim of the thesis is to Design and fabricate an inset fed rectangular Microstrip Antenna and study the effect of antenna dimensions Length (L), Width (W) and substrate parameters relative Dielectric constant (${\varepsilon}r$), substrate thickness on Radiation parameters of Band width. When the antenna was designed, a dual-band, dual-polarized antenna was used to secure the bandwidth and improve performance, and a coaxial probe feeding method so that the phased array of antenna is easy.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.475-481
• /
• 2019

The importance of performance-based design feedback is being emphasized when it comes to the potential impact that affects all the lifecycle of the building. However, the latency and disconnection of domain expert in the sector of AEC/FM remain current obstacles between design and performance feedback. It is hard to utilize performance feedback information for design exploration and support design decision making during the conceptual phase of design. Using parametric design, this paper proposes various design alternatives from a set of rules and constraints defined by algorithms for the geometric configurations of an Office Building. A Building Performance Analysis (BPA) was to developed using Autodesk® Revit® 2019 which integrates Autodesk® Green Building Studio® to predict its sufficient daylighting conditions of the LEED v4's Daylighting Autonomy (DA). The parametric-based performance feedback of this study outlines potential design improvements for further exploration in application to the early design process.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.1
• /
• pp.28-35
• /
• 2003

A numerical analysis of electrochemical reaction and dynamics of the fluid flow in the channels of a DMFC separator was carried out by using a commercial Computational Fluid Dynamics(CFD) code fluent(ver.6.0). From the simulation work, many valuable informations were obtained in terms of distributions of velocity, pressure, temperature, concentration and current density over the flow field. And it was possible to optimize the flow field structure by using the simulation results. The simulation work using the Cm code was found very helpful in analysing the phenomena occurring in the fuel cell and optimizing the structures of electrodes and flow field.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.1
• /
• pp.51-56
• /
• 2008

In this work the realistic install performance analysis of a helicopter was performed together with power extraction enabling to operate auxiliary system as well as intake pressure loss, loss due to bleed air, etc. which must be considered in practical propulsion system's performance modelling to be installed to the airframe. The pressure loss occurring in intake was estimated from the intake performance map with relationships of Mach Number and pressure loss. In order to evaluate the proposed installed performance model, the experimental data for comparison must be needed when mounted in propulsion system. However because of lack of accessibility to such real data at the moment, the alternative way was made through comparison that the analysis results by the proposed model were compared with a wellknown commercial program GASTURB's analysis results. The validity of the proposed installed performance model was consequently confirmed because its average deferences from the GASTURB's results were within 0.5%.

• International Journal of Highway Engineering
• /
• v.10 no.3
• /
• pp.239-246
• /
• 2008

In this study, the influence of reaction temperatures, mixing time and flexible modifier for crumb rubber modified asphalt(CRMA) as processing conditions were investigated. The temperature susceptibility and adhesion properties of neat and modified asphalts at low temperature measured using the penetration and tensile adhesion test. It was found that processing temperatures and flexible modifier were important factors for tensile adhesion strength and toughness energy at low temperature. The CRMA in the higher processing temperature and flexible modifier exhibited improved tensile adhesion properties which indicated the flexible structure of neat and modified asphalt binder. In general, the improvements of the physical properties in the CRMAs were due to the improvements of miscibility between CR and asphalt binder. It was found that the adhesion properties of the flexible agent modified CRMA were higher than CRMA were related to the flexible agent tend to penetrate into CR particles and asphalt binder.

• Journal of Wetlands Research
• /
• v.18 no.3
• /
• pp.226-231
• /
• 2016

Land Generated Waste Load Unit(LGWLU) estimation based on land use data is required to understand the impact of land use on water quality. The method of estimating LGWLU based on the monitoring data requires a lot of time and manpower. In this study, we propose a method of land pollution unit load estimation based on land use data with LP optimization. Optimization is the process to obtain the best possible optimal solution in a given condition. This study carried out optimization by using excel solver in Microsoft Excel. This study derived LGWLU of BOD, T-N, T-P in Gongju-Si and Seocheon-Gun by using the 2012 land use map made by ministry of environment based on 2010 satellite image. This study about LGWLU estimation is expected to be able to determine more clearly the water pollution caused by land use changes.