• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1061-1069
• /
• 1989

본 연구에서는 제조공정을 생략하고, 보다 최종제품의 형상에 가까운 직접압 연법을 실현하기 위한 기초적 연구로서 두개의 회전하는 로울 내부를 냉각하면서 쐐기형 노즐을 통하여 폭이 균일한 용탕을 직접 주입하는 실험방법에 의해서 얻어진 주편의 표면상태와 주조조건과의 관계에 대하여 논하며 또한 기계적성질에 대하여 검토한다.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.537-540
• /
• 2016

유체역학적 추력 방향 제어(Fluidic Thrust Vector Control) 방법 중 하나인 동축류 제어 유동 분사를 이용한 추력 방향 제어(Co-flow Thrust Vector Control)의 작동 특성에 대해서 연구하였다. 이 제어 방법은 점성 유동이 벽면에 부착되어 흐르는 코안다 효과(Coanda Effect)를 이용하여 주 유동을 편향 시키는 방법으로서 그 편향각은 이러한 제어 유동 노즐 출구의 플랩 형상에 영향을 받는 것으로 알려져 있다. 이 연구에서는 출구 플랩 형상을 여러 가지로 바꾸어 가며 주 유동의 전압력 300kPa일 때 제어 유동의 편향각이 포화되는 제어유동의 전압력을 측정하였다. 그 결과 쐐기형 플랩의 각도가 증가할수록 포화 영역에서의 편향각은 증가하며 그 각은 플랩의 각도와 일치한다. 그러나 각도가 증가할수록 제어 유동이 플랩의 벽면을 지나면서 팽창파에 의해 가속되어 충격파을 발생시키게 되고 이 충격파는 주 유동에게까지 전파되어 주 유동 제트의 속도를 감소시킨다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.4
• /
• pp.342-348
• /
• 2017

In this paper, film cooling characteristics at supersonic free stream conditions were examined experimentally by applying an IR-thermography. Film cooling experiments were carried out in a free-jet facility at Mach number of 3.0 and with unit Reynolds number of $42.53{\times}10^6$ and $69.35{\times}10^6$ using wedge shaped film cooling model which has a converging film cooling nozzle. Film cooling efficiency was calculated by measuring the surface temperature of PEEK(Polyether Ether Ketone) and the effects of angle of attack and blowing ratios on the film cooling efficiency were examined. The measured wall temperature was significantly reduced by the film cooling flow compared with the results without the film cooling flow. The usefulness of film cooling was also confirmed by the surface heat flux calculated using the surface temperature history of PEEK. As the blowing ratio increases the protected area of PEEK was also expanded along the direction of free stream and film cooling flow.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.3
• /
• pp.41-49
• /
• 1999

A feasibility study is performed for practical application of a Ventilating Water-Jet(VWJ) propulsor which attracts new attention as a candidate propulsor for super-high speed vessels. Super-cavitating foil sections are adopted for the rotor blades since the rotor is operating at ventilating condition. Wedge type and cavitator type foil sections are used for the design of rotor blades. Other geometric characteristics of rotors are selected from the Kaplan type ducted propeller rotors. The test section of KRISO cavitation tunnel is modified to perform open-water tests of the VWJ propulsors. The tests are performed both at fully-submerged and free-jet conditions. Ventilation occurred at the free-jet condition by sucking the air in the downstream side of the rotor, which easily develops as super-cavitation when the rotor operates at lower advance coefficients. Spoilers are attached at the trailing end of the pressure side of the blade section, in order to increase the lift force.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.1
• /
• pp.88-97
• /
• 2022

In this study, a vitiated air heater was designed and manufactured to supply high-temperature and high-pressure air to the ground test apparatus of a direct-connected supersonic combustor, and an experiment was performed to verify the target design point. By installing wedges at the upper boundary, lower boundary and center of the nozzle exit of the vitiated air heater, it was confirmed that the Mach number satisfies the 2.0 level, and the pressure of the combustion chamber was also satisfactory compared to the design point. In the case of temperature, the measured temperature deviation was large due to the degree of exposure of the thermocouple and the slow response characteristics. After that, the isolator was connected to the rear of the vitiated air heater, and the Mach number was measured in the same method, and the Mach number at the center of the isolator eixt was slightly reduced to 1.8~1.9.