DOI QR코드

DOI QR Code

An Experimental Study of Film Cooling Characteristics at Supersonic Free Stream Conditions

초음속 주유동 환경에서의 막냉각 특성 시험 연구

  • Kim, Manshik (The 1st Research and Development Institute, Agency for Defense Development) ;
  • Lee, Dong Min (The 1st Research and Development Institute, Agency for Defense Development)
  • Received : 2016.08.03
  • Accepted : 2017.03.08
  • Published : 2017.04.01

Abstract

In this paper, film cooling characteristics at supersonic free stream conditions were examined experimentally by applying an IR-thermography. Film cooling experiments were carried out in a free-jet facility at Mach number of 3.0 and with unit Reynolds number of $42.53{\times}10^6$ and $69.35{\times}10^6$ using wedge shaped film cooling model which has a converging film cooling nozzle. Film cooling efficiency was calculated by measuring the surface temperature of PEEK(Polyether Ether Ketone) and the effects of angle of attack and blowing ratios on the film cooling efficiency were examined. The measured wall temperature was significantly reduced by the film cooling flow compared with the results without the film cooling flow. The usefulness of film cooling was also confirmed by the surface heat flux calculated using the surface temperature history of PEEK. As the blowing ratio increases the protected area of PEEK was also expanded along the direction of free stream and film cooling flow.

본 연구에서는 초음속 주유동 환경에서의 막냉각 특성에 대해 적외선 열상법을 적용한 시험을 수행하였다. 막냉각 시험은 수축형 막냉각 노즐을 갖는 쐐기형 막냉각 시편을 이용해 마하수 3.0, 단위 길이 당 레이놀즈수 $42.53{\times}10^6$$69.35{\times}10^6$ 인 조건을 구현한 자유-제트 시험 설비에서 수행하였다. 모사 탐색창에 해당하는 PEEK의 표면 온도를 계측하여 막냉각 효율을 산출하였고 받음각 및 분사율이 막냉각 효율에 미치는 영향을 분석하였다. 막냉각을 적용하지 않는 경우와 비교할 때, 막냉각을 적용할 경우 측정된 PEEK의 표면 온도가 크게 감소하였다. 막냉각의 유용성은 시간에 따른 PEEK의 표면 온도로부터 산출한 열유속 특성으로도 확인할 수 있다. 분사율이 증가할수록 보호되는 PEEK의 영역이 주유동과 막냉각 유동의 흐름 방향으로 확장되었다.

Keywords

References

  1. Cho, H., Kim, B., and Lee, D., "Heat/Mass Transfer Characteristics around Film Cooling Hole with Compound Angle Orientations," Journal of the Korean Society for Aeronautical and Space Sciences, Vol. 26, No. 1, 1998, pp.35-44
  2. Choi, Y., Jeong, H., Kim, Y. and Kim, S., "Experimental Study of Film Cooling in Liquid Rocket Engine(I)," Journal of the Korean Society for Aeronautical and Space Sciences, Vol. 33, No. 6, 2005, pp.71-75 https://doi.org/10.5139/JKSAS.2005.33.6.071
  3. Morris, H., Majeski, J. and Rawlinson, E., "Development of IR Sensor Window Cooling Requirements for Endoatmospheric Interceptors," AIAA 91-1439, 26th Thermophysics Conference, June, 1991
  4. Lee, G., Son, C. and Kim, T., "2-Dimensional Film Cooling Characteristics with the Height Variation of a Stepped Slot Exit," Trans. of the KSME(B), Vol. 29, No. 1, 2005, pp.46-54
  5. Juhany, K., Hunt, M. and Sivo, J., "Influence of Injectant Mach Number and Temperature on Supersonic Film Cooling," Journal of Thermophysics and Heat Transfer, Vol. 8, No. 1, 1994, pp.59-67 https://doi.org/10.2514/3.501
  6. Majeski, J. and Morris, H., "An Experimental and Computational Investigation of Film Cooling Effects on an Interceptor Forebody at Mach 10," AIAA 90-0622, 28th Aerospace Sciences Meeting, Jan., 1990
  7. Kim, I., Lee, J., Park, G., Byun, Y. and Lee, J, "Test Research Using an IR Thermography Technique in a Supersonic Wind Tunnel," Journal of the Korean Society for Aeronautical and Space Sciences, Vol. 44, No. 2, 2016, pp.99-107 https://doi.org/10.5139/JKSAS.2016.44.2.99
  8. Schultz, D. and Jones, T., "Heat Transfer Measurements in Short-Duration Hypersonic Facilities," AGARD-AG-165, 1973