• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.3
• /
• pp.59-64
• /
• 1994

A study was conducted to investigate the propeller singing place of an 86, 000 ton Deadweight Crude Oil Tanker. In preliminary study, proper use of finite element analysis was verified by comparing with the result of hammering test in the air. Then the finite element analysis was carried out for the blade in the water and compared with the noise measurement during sea trial, which enabled to confirm the local resonances of blade structure. Result of the study showed that the singing occurred most probably at trailing edges on the blade tip over 95% of propeller diameter. Owing to edge cutting of a successfoul remdial action, the singing excitation forces seemed to be reduced whereas the vibration characteristics of the blade was not changed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.15-24
• /
• 2019

The optimum solutions of MOSCOS antenna arrangement were studied to solve the EMI between it and EWT mounted on an MTB. Two candidates of optimal place for MOSCOS antenna were determined by using a fishbone diagram to determine seven reasons based on 4M1E, to identify the design factors on Friis equations, and to analyze the case study of EMI related to MOSCOS. MOSCOS antenna was rearranged by the final optimal position, which was selected by measuring the Power Spectral Density (PSD) at two locations, and the proposed improvement was tested on board to determine its efficiency.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2019.05a
• /
• pp.121-122
• /
• 2019

차도선과 같은 연안 화물 여객선에는 필수 탑재 항해통신장비 이외에 유지보수 지원이나 운항 효율 향상을 위한 장비는 거의 탑재 되어 있지 않은 상황으로 ICT 기술 기반 운영 및 유지보수(O&M, operating and maintenance) 지원 서비스 제공 시스템 도입이 필요하다. 이에 중소형 선박 기자재의 데이터 수집, 통합, 분석을 통해 선박 관리, 유지보수 지원, 운항 모니터링 등의 스마트 O&M 서비스를 제공하기 위한 시스템의 개발을 진행 중에 있다. 개발하는 시스템은 빅데이터 분석 기술, 모바일 어플리케이션 개발 기술, 증강현실(AR) 기술을 기반으로 선박을 구성하는 요소의 상태 모니터링, 최적 관리, 원격 유지보수 지원 등의 서비스를 제공할 예정이다. 또한, 클라우드 기반 육해상 통합 O&M 서비스 지원 시스템의 개발을 통해 선단 단위 분석, 중소형 해운선사 소모품 관리 및 운영 지원 등 종합적인 부가 서비스를 제공하는 것이 목적이다. 이러한 시스템의 개발이 완료되면, 실선 시험을 통해 개발 시스템과 서비스의 유용성을 검증할 계획이다. 본 논문에서는 이러한 O&M 지원을 위한 시스템에 관해 소개하고, 앞서 언급한 각종 서비스를 제공하기 위한 선박 및 육상 측 구성요소 정의와 서비스 아키텍처의 설계에 관한 내용을 다룬다.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2023.05a
• /
• pp.261-262
• /
• 2023

자율운항선박의 도래와 예상 할 수 없는 선박의 구조 변화 및 적화 상태 변화로 인한 전복사고로부터 선박을 보호하기 위해서는 선박의 복원성 상태를 실시간으로 모니터링 것이 매우 중요합니다. 자율운항선박의 복원성 상태를 실시간으로 정밀 모니터링 시스템 개발은 운항자에게 사전에 위험을 경고하고 적화상태 보완 또는 평형수 상태 변형 등을 통하여 추가적은 복원성 확보를 위해서 필수적입니다. 본 연구는 실습선의 전자 경사계로 실시간 횡요 주기로 추정한 선박의 메타센터 높이(GM)의 정확도를 실험적으로 검증 하였습니다. 본 연구는 선박의 전자 경사계를 사용하여 선박의 복원성 안정성 상태를 실시간으로 평가하여 추정한 선박 GM의 정확도와 향후 연구에서 시스템 개선을 위한 요구 사항을 제시하였습니다.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.4
• /
• pp.249-256
• /
• 2019

A full-scale test line was established to verify the electrical environmental interferences caused by the HVDC ±500 kV Double Bipole overhead transmission line with metallic return conductor, which is scheduled for construction in Korea and the fullscale test was conducted for one year. And through the human perception test of the DC electric-field under the HVDC Double Bipole line, the threshold value at which the human detects DC electric field was investigated to verify the validity of the design guide for the HVDC ±500 kV Double Bipole overhead transmission line. The polarity configuration of the HVDC ±500 kV Double Bipole test line was arranged diagonally with the same polarity in terms of the electrical environment disturbance and operation. The test line utilized the 6-bundle arrangement to prevent the corona discharge taking into account the domestic social acceptability. The test results show that the HVDC ±500 kV Double Bipole transmission line generated very little corona discharge from the conductors. Therefore, both DC electric field and ion current density met the domestic design guide for DC overhead transmission lines. Also, the human perception test of DC electric fields under the test line showed that 70% of participants did not recognize the DC electric field even when exposed to 23 kV/m.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.5
• /
• pp.457-464
• /
• 2011

This paper deal with the validation of correction method of ice strength and thickness to the sea trial condition based on the ice model test results. It is very difficult to conduct the model test corresponding to the sea trial condition exactly. In addition, the available sea trial data is not sufficient for the validation of correction method. In the present study, the model test results of Terry-Fox ice breker have been used to compare the corrected results of sea trial test by varying its thickness and strength of model ice. The HSVA and ITTC methods have been applied to the present comparisions and the required power has been also validated by using the HSVA method. There are rather good agreement between the sea trial result and model test corrected by the HSVA and ITTC method. The more comparisons are expected to be carried out in near future.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.5
• /
• pp.88-92
• /
• 2013

The icebreaking research vessel (IBRV) ARAON had her second ice trial in the Arctic Ocean in the summer season of 2010. During the voyage, the local ice loads acting on the bow of the port side were measured using 14 strain gauges. These measurements were carried out in three icebreaking performance tests. To convert the measured strains into the local ice pressures, a finite element model of the instrumented area was developed. The influence coefficient method (ICM), which uses the influence coefficient from the finite element model, and the direct method, which uses the measured strain, were selected as the conversion methods. As a result, the maximum measured pressure was 1.236MPa, and the average difference between ICM and the direct method was about 5% for an area of $0.2m^2$. The pressure-area relationship of the measurement falls below the range of the existing pressure-area curve, which is due to the low ice strength of melted ice in the summer.

• Journal of the Society of Naval Architects of Korea
• /
• v.38 no.3
• /
• pp.14-22
• /
• 2001

This paper presents the results of hull form design and powering performance for a 2.500 ton class trimaran frigate. A series of resistance tests and numerical calculations have been conducted to figure out the influences of side-hull form and position on the resistance characteristics of the trimaran. And the propulsion test was conducted to investigate the propulsion efficiency of the trimaran, and the powering performance of the trimaran was compared with that of the similar mono-hull ships in full scale. From the research it was found that the longitudinal position of side-hull had a large influence on the resistance characteristics of the trimaran while the side-hull form and transverse position had a small influence on it. The trimaran showed favorable resistance performance when the side-hull was located near the stern of trimaran, which was resulted from the fact that the side-hull stem was located near the primary wave hollow generated by the main hul1. The powering performance of the trimaran was superior to that of the similar mono-hull ships above the middle speed range.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.2
• /
• pp.135-145
• /
• 2023

Developing high-fidelity Computational Fluid Dynamics (CFD) simulation methods used to evaluate the airwake characteristics along a flight deck of a large ship, the various kind of data such as actual ship measurement and wind tunnel results are required to verify the accuracy of CFD simulation. Inflow velocity profile at the bow, local unsteady flow field data around the flight deck, and highly reliable wind tunnel data which were measured after reviewing Atmospheric Boundary Layer (ABL) simulation and Reynolds Number effects were also used to determine the key parameters such as turbulence model, time resolution and accuracy, grid resolution and type, inflow condition, domain size, simulation length, and so on in STAR CCM⁺. Velocity ratio and turbulent intensity difference between Full-scale CFD and actual ship measurement at the measurement points show less than 2% and 1.7% respectively. And differences in velocity ratio and turbulence intensity between wind tunnel test and small-scale CFD are both less than 2.2%. Based upon this fact, the selected parameters in CFD simulation are highly reliable for a specific wind condition.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.25 no.4
• /
• pp.7-12
• /
• 1988

The Resistance Committee of Korea Towing Tank Conference extended the Cooperative Experimental Study Program(1985)[1] to perform the geosim tests by exchanging the five different scaled Series 60, $C_B=0.60$ models between the participating organizations and 13 sets of resistance data have been obtained. The test results are compared among the participating towing tanks and also with the results given in the report of the Resistance and Flow Com-identify the mittee of 18th ITTC. The form factor of each model is derived by Prohaska's method to investigate its dependency on $R_n$. On the other hand, at each $F_n$, form factors are also derived by Telfer's method to relation between $F_n$ and form factor. For this hull form, form factors show relatively weak dependency on $R_n$ and strong dependency on $F_n$. And it is also found that dependencies on both have a cross relation. It seems that further study should be continued to understand more clearly the physical phenomena involved in this problem.