• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.2
• /
• pp.139-147
• /
• 2005

The lubricant impregnated MC nylon has good frictional properties, but its mechanical strength is inferior to steel for the mechanical elements. For the tribological application Nylon as gears, sliding bearings, cam and etc, the steel shafts are fitted in pre-heated nylon cylinder by a process of interference expansion fit and bonded by induction heating method. The joint shear strength of the two materials was measured by a universal test machine. From the study, the adhesive shear strength between these two materials was affected by the factors of the interference between nylon and steel, the size of nylon cylinder, knurl of steel shaft and inducting heating conditions. The most effective jointing conditions were analyzed and decided for the practical application in the industry.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.4
• /
• pp.58-71
• /
• 1996

A model which calculates the hydrocarbon emissions from spark ignition engines is presented The model contains the formation of HC emissions due to both crevices around piston ring top land and oil films on the cylinder wall. The model also considers in-cylinder oxidation and exhaust port oxidation of desorbed HC from crevices and oil films after combustion process. The HC emissions model utilizes the results of SI engine cycle simulation. The model predicts well the trends of HC emissions from the engines when varying engine parameters.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.147-158
• /
• 1997

This paper presents the analysis technique and procedure of main engine components-cylinder block, cylinder liners, gasket and cylinder head-using the finite element method, which aims to assess mainly the potential of lower oil consumption in a view point of engine design and to decide subsequently the accuracy of engine design which was done. The F.E. model of an engine section consisting of one whole cylinder and two adjacent half cylinders is used, whereby the crankcase is cut off at the block bottom deck. By means of a 3-dimensional F.E. model-including cylinder block, liners, gasket, cylinder head, bolts and valve seat rings as separate parts a linear analysis of deformations and stresses was performed for three different loading conditions;assembly, thermal and gas loads. For the analysis of thermal boundary conditions also the temperature field had to be evaluated in a subsequent step.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.11
• /
• pp.932-938
• /
• 2017

Particle-in-cell method which blends Eulerian grids and Lagrangian particle is utilized to solve simplified hall-effect thruster. Since this study individually tracks not only neutrons and ions but also electrons, message passing interface(mpi) scheme is adopted for parallel computer cluster. Helical movement of an electron cloud in constant magnetic field is validated comparing with an exact solution. A plasma in radial magnetic field and axial electric field in a reaction cylinder is established. Electrons do double helix movement and are well anchored in a cylinder. Ionization of neutrons by impact with high-speed electrons generates ion particles. They are accelerated by axial electric field, which forms a plume of a plasma-effect thruster.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.4
• /
• pp.34-39
• /
• 2006

The flow forming has been used to produce long thin walled tube parts, with reduced forming force and enhanced mechanical for a good finished part, compared with other method formed parts. Especially, the flow forming is suitable for making high precision thin walled cylinders, such as rocket motor cases, combustion chamber, hydraulic cylinders and high-pressure vessels and so on. In this paper, finite element analysis of three-roller forward and backward flow forming for combustion chamber is carried out to study effects of forming depth and feed rate on forming force. The axial and radial forming forces of forward flow forming on several forming depth and feed rate conditions are compared with those of backward flow forming.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.5
• /
• pp.430-435
• /
• 2013

This study is investigation of the characteristics for acoustic emission signal generated by destruction on glass fiber bundles and specimen that was machined composite materials surrounding the outside of GFRP cylinder. The Amplitude of acoustic emission signal gets bigger as the cutting angle of knife increases. Accordingly, the number of hits in destruction of composite materials specimen have more in longitudinal direction (longitudinal direction to the glass fiber) than in hoop direction (horizontal direction to the glass fiber) while the amplitude of signals were bigger in hoop direction than longitudinal direction. It was found out that the amplitude of the glass fiber breakage is more than 40 dB and that the amplitude of signal for matrix crack was less than 40 dB because matrix crack signal was not observed when threshold value is 40 dB and matrix crack signal suddenly appered when threshold value is 32 dB. The slope of the amplitude is related to the acoustic emission source and the slope of the amplitude of the horizontal and vertical directions are 0.16 and 0.08. In particular, The slope of the amplitude of longitudinal direction breakage appear similar to the glass fiber breakage and therefore Acoustic emission source of longitudinal direction breakage is estimated the glass fiber breakage.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.2
• /
• pp.127-133
• /
• 2011

The following Technology Report was written with respect to recent offshore technology development. This report was prepared with the purpose of suggesting recent offshore technology and upcoming visions by describing the principles of an offshore drilling operation, the NL Tensioner Cylinder Package R & D, and the general technology related to three offshore patent areas, as major contents.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.435-439
• /
• 2002

In the pneumatic system, pneumatic cylinder is wildly used to factory automation. In general, Pneumatic cylinder problems are occured with colliding to stroke end part at which piston collide to end-cap, head cap and tube when piston is loading. This appearances have a short life of cylinder and is due to system destruction. This study examines the dynamic characteristics of pneumatic cushioning cylinder and cushion sleeve design. At head part cushion chamber for the vertical experimental, The decisions of cushioning effect and the results of the experimental research are obtained to the followings: i) The cushioning effects could acqure to the reserch, if the compressible energy is more than kinetic ones. ii) The collision of piston and head cover could acqure to the research, if the kinetic energy is more than compressible iii) If the load increase to the rolling car, the cushion region pressures would increase and the dynamic force.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.745-745
• /
• 2012

원자력발전소에서 비상디젤발전기는 노심의 안전성을 지키는 매우 중요한 역할을 담당하고 있다. 이를 위해 디젤발전기는 신뢰성능 높게 유지하도록 규제요건이 마련되어 있다. 디젤발전기의 엔진 상태를 주기적으로 감시하고 평가하기 위해서는 엔진 상태 신호 분석 기술이 필요하다. 엔진 상태 신호 분석에는 연소분석과 진동 및 초음파 측정 및 분석기술이 중요한 비중을 차지한다. 연소 분석은 디젤 엔진의 개별 실린더에 대한 연소 성능에 대한 정보를 제공한다. 진동 및 초음파 분석은 이벤트 타이밍과 기계적 상태에 대한 정보를 알려준다. 이들 신호는 정상적인 부하로 운전하는 디젤엔진의 가동에 영향을 미치지 않고 수집할 수 있다. 엔진 상태 신호 분석을 이용하는 주요 동기는 전통적으로 장비 제작자의 권고에 따라 수행되는 분해-검사 유지 보수 프로그램을 일부 대체하고 예측정비를 통해 신뢰도를 유지하기 위함이다. 상태 진단정비는 엔진 상태 신호분석을 주로 이용하여 엔진의 신뢰도와 이용률을 증가시킬 수 있다. 본 논문에서는 국내외서 경험한 엔진상태신호 측정 및 분석 사례를 기술하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.380-384
• /
• 1992

The position control of a pneumatic cylinder suing low cost on-off valves is studied. The valve control band(VCB) was proposed toget fast response and toprevent solenoid valves from unnecessary switching at the beginning of response. A learning algorithm was used to compensate the nonlinearity and complexity in mathematical modelling of pheumatic on-off controlled positioning systems. In this algorithm, the desired performance index and modified learning rate, were proposed to improvespeed and convergence of learning control. It is shown experimentally that the proposed algorithm is robust to changes of system parameters: the setting time less than 1.0 sec and the error bound of .+-. 0.1 mm can be obtained. The effects of supply pressure, size of switching valves and the effect of multiple valves are discussed, and computer simulation onthe dynamic performances of the pneumatic system is also presented.