• Journal of the Korean Institute of Landscape Architecture
• /
• v.48 no.5
• /
• pp.80-88
• /
• 2020

With the issuance of one-week fine dust emergency reduction measures in March 2019, the public's anxiety about fine dust is increasingly growing. In order to assess the application of air purifying plant-based bio-filters to public facilities, this study presented a method for measuring pollutant reduction effects by creating an indoor environment for continuous discharge of particle pollutants and conducted basic studies to verify whether indoor air quality has improved through the system. In this study conducted in a lecture room in spring, the background concentration was created by using mosquito repellent incense as a pollutant one hour before monitoring. Then, according to the schedule, the fine dust reduction capacity was monitored by irrigating for two hours and venting air for one hour. PM₁₀, PM_2.5, and temperature & humidity sensors were installed two meters front of the bio-filters, and velocity probes were installed at the center of the three air vents to conduct time-series monitoring. The average face velocity of three air vents set up in the bio-filter was 0.38±0.16 m/s. Total air-conditioning air volume was calculated at 776.89±320.16㎥/h by applying an air vent area of 0.29m×0.65m after deducing damper area. With the system in operation, average temperature and average relative humidity were maintained at 21.5-22.3℃, and 63.79-73.6%, respectively, which indicates that it satisfies temperature and humidity range of various conditions of preceding studies. When the effects of raising relatively humidity rapidly by operating system's air-conditioning function are used efficiently, it would be possible to reduce indoor fine dust and maintain appropriate relative humidity seasonally. Concentration of fine dust increased the same in all cycles before operating the bio-filter system. After operating the system, in cycle 1 blast section (C-1, β=-3.83, β=-2.45), particulate matters (PM₁₀) were lowered by up to 28.8% or 560.3㎍/㎥ and fine particulate matters (PM_2.5) were reduced by up to 28.0% or 350.0㎍/㎥. Then, the concentration of find dust (PM₁₀, PM_2.5) was reduced by up to 32.6% or 647.0㎍/㎥ and 32.4% or 401.3㎍/㎥ respectively through reduction in cycle 2 blast section (C-2, β=-5.50, β=-3.30) and up to 30.8% or 732.7㎍/㎥ and 31.0% or 459.3㎍/㎥ respectively through reduction in cycle 3 blast section (C-3, β=5.48, β=-3.51). By referring to standards and regulations related to the installation of vegetation bio-filters in public facilities, this study provided plans on how to set up objective performance evaluation environment. By doing so, it was possible to create monitoring infrastructure more objective than a regular lecture room environment and secure relatively reliable data.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.4
• /
• pp.1751-1758
• /
• 2012

Capillary blood sampling on the forearm reduces pain caused by skin puncture. The present study compared the blood glucose test results performed at different sampling sites of the forearm, finger, and vein to evaluate clinical validity of this alternative site blood sampling technique. Subjects numbered 555 including 61 diabetic patients participated to measure the glucose concentration on the finger ($G_F$) and the forearm ($G_A$) with a portable glucometer under overnight fasting state. Then, the venous glucose concentration ($G_V$) was measured in 514 subjects in less than 1 hour. The test results were analyzed by simple linear regression, intraclass correlation, and Passing-Bablok regression techniques. $G_A$ was highly correlated with $G_F$ or $G_V$ showing the correlation coefficients (r) of approximately 0.97 (P<0.0001) in the normal group. The patient group also resulted similarly high correlation with only slightly lower r value. The mean differences in glucose concentration were less than ${\pm}10mg/dL$ regardless of the sampling sites. Intraclass correlation coefficients were slightly smaller than r but very much similar in value in both groups. The 95% confidence intervals of the slope as well as the intercept in the Passing-Bablok regression analysis were < ${\pm}20%$ and < ${\pm}20mg/dL$, respectively, which were within the clinically acceptable ranges. These three statistical techniques introduced in the present study well demonstrated the consistency of $G_A$ with $G_F$ and $G_V$. Therefore, the forearm blood glucose test could be considered as clinically valid under fasting condition.

• Journal of Food Hygiene and Safety
• /
• v.27 no.3
• /
• pp.271-276
• /
• 2012

This study intented to standardize the method for total polysaccharide, which is a functional marker for aloe vera gel in Korea. We used four lyophilized raw materials and commercial aloe gel products, certified as Health Functional Food by Korea Food and Drug Administration, including powder, solution, jelly, tablet and capsule, to optimize the analytical condition of dialysis and phenol-sulfuric acid reaction in polysaccharide analysis. The optimal conditions for polysaccharide analysis included 1 L water for dialysis and change 3 times for 24hr against 25 mL prepared sample solution. Validation test showed lower than 5% of coefficient of variation(CV) in intra-, interday validation in lyophilized raw materials and 4 types of commercial products. In inter-person and inter-laboratory validation with 4 persons from 4 different laboratories, CV(%) were 5.50 and 6.64 respectively. The linearity of polysaccharide analysis was assessed using 5 serial concentration of lyophilized raw materials(0.1, 0.2, 0.3, 0.4, 0.5%(w/v)). The results showed $R^2{\geq}0.995$ of high linearity. In the commercial aloe vera gel products, the results of reproductivity showed lower than 7.08% and revealed that the standardized method from this study ensured high precision for polysaccharide analysis.

• Journal of Communication Design
• /
• v.68
• /
• pp.278-288
• /
• 2019

The purpose of this study is to analyze the effects of risk and convenience on purchase intention in the IOT market, and I want to analyze the moderating effect of emotional consumption value. In this study, two products were selected from three product groups. There are three major methods of research. First, theoretical considerations. Second, survey analysis. Reliability analysis and factor analysis were performed using descriptive statistics using SPSS. Third, we measured changes of EEG according to in - depth interview and indirect experience. As a result of the hypothesis of this study, it was confirmed that convenience of use of IoT product influences purchase intention. Risk was predicted to have a negative effect on purchase intentions, but not significant in this study. This implies that IoT products tend to be neglected in terms of monetary loss such as cost of purchase, cost of use, and disposal cost when purchasing. In-depth interviews and EEG analysis revealed that there is a desire to purchase and try out the IoT product due to the nature of the product, the novelty of new technology, and the vague idea that it will benefit my life. The aesthetic, symbolic, and pleasure factors, which are sub - elements of emotional consumption value, were found to have a great influence. This is consistent with previous research showing that emotional consumption value has a positive effect on purchase intention. In-depth interviews and EEG analyzes also yielded the same results. This study has revealed that emotional consumption value affects the intention to purchase IoT products. It seems that companies producing IoT products need to concentrate on marketing with more emotional consumption value.

• Geotechnical Engineering
• /
• v.7 no.3
• /
• pp.51-64
• /
• 1991

The reliable estimation of pile bearing capacity is essential for the improvement of the re- liability and the cost-effectiveness of the design. There have been numerous pile bearing capacity prediction methods proposed up to now, however, execpt for the estimation made from the result of the pile loading test, not one method is appropriate for the reliable prediction. Due to the considerable time and expenses required to carry out the pile loading test, the test has seldom been utilized. The development of Simple Pile Loading Test(SPLT) which utilizes the pile skin friction as the required reaction force to cause the pile tip settlement, provides a solution to perform more pile loading tests and consequently a more economical pile design is possible. The separate measurement of skin friction and tip resistance during the course of performing SPLT provides a better understanding of the pile behavior than the result of the conventional pile loading test where only the total resistance is measured. On the other hand, there are some points to be clarified in order to apply the test results of SPLT to practical problem. They are the direction of the applied load to mobilize the skin friction and the use of reduced sized sliding core. In this research, both the SPLT and the conventional pile loading test on 406mm diameter steel pipe pile have been performed. From the result, it would be safe to use the measured SPLT skin friction value directly in the design, since the value is somewhat lower than the value measured in the conventional test. It is further assumed that the tip resistance value of the reduced sized sliding core should properly be analysed by taking the incluonce of scale effect into consideration.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.47 no.3
• /
• pp.23-31
• /
• 2010

The increasing demands on low-power, and low-complexity video encoder have been motivating extensive research activities on distributed video coding (DVC) in which the encoder compresses frames without utilizing inter-frame statistical correlation. In DVC encoder, contrary to the conventional video encoder, an error control code compresses the video frames by representing the frames in the form of syndrome bits. In the meantime, the DVC decoder generates side information which is modeled as a noisy version of the original video frames, and a decoder of the error-control code corrects the errors in the side information with the syndrome bits. The noisy observation, i.e., the side information can be understood as the output of a virtual channel corresponding to the orignal video frames, and the conditional probability of the virtual channel model is assumed to follow a Laplacian distribution. Thus, performance improvement of DVC systems depends on performances of the error-control code and the optimal reconstruction step in the DVC decoder. In turn, the performances of two constituent blocks are directly related to a better estimation of the parameter of the correlation channel. In this paper, we propose an algorithm to estimate the parameter of the correlation channel and also a low-complexity version of the proposed algorithm. In particular, the proposed algorithm minimizes squared-error of the Laplacian probability distribution and the empirical observations. Finally, we show that the conventional algorithm can be improved by adopting a confidential window. The proposed algorithm results in PSNR gain up to 1.8 dB and 1.1 dB on Mother and Foreman video sequences, respectively.

• Applied Chemistry for Engineering
• /
• v.10 no.5
• /
• pp.718-725
• /
• 1999

In order to investigate the interaction characteristics of poly(dimethylsiloxane) (PDMS) with various solvents such as water, ethanol, and iso-propanol, Inverse Gas Chromatography(IGC) at finite concentration, which is a very fast, accurate, and thus promising technique in thermodynamic study of polymer systems, is employed. By measuring the specific retention volumes of the probes, the interaction parameters are calculated by means of the Flory-Huggins equation. From the results, the interaction parameters of the probes are, as expected due to the hydrophobicity of the polymer, found to be of large positive values (2$2.0{\times}10^{-3}mol/g$. For the linear PDMS, interpretation of the space distribution of molecules is performed by the Kirkwood-Buff-Zimm(KBZ) integrals, which give intuitive information about physical properties. From the KBZ integrals, water does not show the tendency of preferential solvation with the PDMS but formed self-cluster. The larger solvent molecules show a stronger tendency to distribute more randomly in the mixture.

• Analytical Science and Technology
• /
• v.28 no.6
• /
• pp.460-466
• /
• 2015

An isotope dilution liquid chromatography tandem mass spectrometry was developed as a primary method for the quantitative analysis of cholesterol in infant formula. Cholesterol-d₄ was used as an internal standard and spiked into the infant formula sample. In order to release cholesterol out of cholesteryl ester, which is cholesterol bound to fatty acids in infant formula, saponification was carried out. Saponification conditions were optimized with heating temperature, reaction time and the concentration of KOH. The optimum conditions were as follows; heating temperature was 70 ℃, reaction time was 180 min and the concentration of KOH was 0.8 mL of 8 M KOH for about 0.1 g infant formula sample. Extraction of cholesterol out of sample solution was carried out with hexane uisng liquid-liquid extraction. Chromatographic analysis was carried out using Phenomenex Kinetex C₁₈ column. Mobile phase was 0.1% acetic acid in methanol/water (v/v, 99/1) and flow rate was 0.3 mL/min. Cholesterol and cholesterol-d₄ were monitored at mass transfer m/z 369/259 and 373/263 respectively. Reproducibility of the method was evaluated to be 0.23% of the measurement result. The expanded uncertainty of the measurement result of cholesterol in infant formula was approximately 1.9% at a 95% confidence level. NIST standard reference material having certified values of cholesterol in infant formula, was analyzed in order to verify this method. The ID-LC/MS/MS results were well agreed with the certified values of NIST SRM within the uncertainty.

• Journal of Oral Medicine and Pain
• /
• v.30 no.3
• /
• pp.345-351
• /
• 2005

The purpose of this double-blind study was to evaluate clinical effects of botulinum toxin type A (BTX-A) injection on myofascial pain syndrome (MPS) involving upper trapezius and compare with those of lidocaine injection. 21 patients presenting with active TrP1 and/or TrP2 in the upper trapezius over 6 months were selected for this study. The subjects were randomly divided into two groups; one group injected with BTX-A (15 unit of $Botox^{(R)}$ / 0.3 ml per trigger point (TrP)) and the other group injected with 0.5% lidocaine (0.3 ml /TrP). The clinical effects were evaluated by VAS and PPT at baseline, 2, 4, 6 and 8 weeks after treatment. BTX-A group showed persistent decrease of VAS values and increase of PPT values following treatment. While there was no significant difference in VAS values between BTX-A and lidocaine groups (p=0.347), there was significant difference in PPT values after treatment between two groups (p=0.000). The subjects received BTX-A showed noticeable improvement in PPT values after treatment, suggesting more reliable effect of BTX-A injection compared with lidocaine injection. The results of this study support that the direct injection of BTX-A to a TrP is an effective and safe treatment for MPS involving upper trapezius.

• Clinical and Experimental Reproductive Medicine
• /
• v.36 no.4
• /
• pp.255-263
• /
• 2009

Objective: The objective of the study was to determine the diagnostic performance of transabdominal ultrasound by receiver operating characteristic (ROC) curve analysis, in order to evaluate the usefulness in establishing the diagnosis of polycystic ovary syndrome (PCOS). Methods: Questionnaires were given to 8,793 reproductive women reviewed at Ewha Womans University Mokdong hospital. Ultrasound examinations were performed in 701 women with a transabdominal transducer. Transabdominal ultrasounds were performed in 185 normal control women (normal menstruation without hyperandrogenism or PCO morphology) and 248 PCOS patients according to National Institutes of Health (NIH) PCOS diagnosis criteria. ROC curves were calculated for ovarian volume and follicle number. Results: In normal control group, the mean age were $23.64{\pm}4.26$ years old and the mean ovarian volume and follicle number were $6.03{\pm}1.89\;cm^3$ and $6.49{\pm}1.93$, respectively. The ovarian volume showed an area under the ROC curve (AURC) of 0.761. A ovarian volume decision threshold >$9\;cm^3$ had a sensitivity of 51.0% and a specificity of 91.4% for the diagnosis of PCOS. The follicle number showed an AURC of 0.733. A follicle number decision threshold ${\geq}9$ had a sensitivity of 54.9% and a specificity of 87.0% for the diagnosis of PCOS. A follicle number decision threshold ${\geq}10$ had a sensitivity of 53.2% and a specificity of 90.4%. A follicle number and a ovarian volume did not have a high diagnostic power for screening for PCOS. Conclusion: Our results suggest that transabdominal ultrasound assessment is not effective for the detection of PCOS in young women of reproductive age.