• Explosives and Blasting
• /
• v.31 no.1
• /
• pp.1-10
• /
• 2013

In blasting demolition, a method would be chosen among many depends on shape and system of a structure and its surround. To demolish using explosives a structure, which is asymmetric and with high aspect ratio, pre-weakening, explosive locations, detonating delay, and surround conditions are needed to be considered in front to design blasting demolition plan. In this study, to over turn asymmetric and high aspect ratio structure in safe, a simulation using a software named Extreme Loadings for Structures, ELS, had performed. In results, it is achieved optimized pre-weakening shapes and locations, which prevent kick back motion of the structure when it collapse, by analyzing moment distribution caused by pre-weakening. And of structural collapse and by minimizing asymmetric structure's torsional moment. Also, after the demolition, simulation results are also compared with actual collapse behavior. In results, it is confirmed the accuracy of collapse behaviour simulation results, and in blasting demolition, kick back motion can be controled by adjusting pre-weakening shape and location, and the torsional moment of an asymmetric structure also can be solved by optimizing detonation locations and its time intervals.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.7
• /
• pp.31-38
• /
• 2013

After debris flow caused damage during recent years, many scholars and engineers have thrown their effort into analyzing risk from debris flow in Korea. But it is hard to predict damage by debris flow taken place in wide area. Recently, SINMAP program is widely well used to estimate the amount of debris flow and its' range. In order to make frequent use of it, the most important thing is selection of accurate input parameters. In-situ experiments, which are avaliable in the mountain, is to be suggested to get dependable input parameters for SINMAP. Those are permeability, cohesion, density, friction angle and thickness in SINMAP. To get those, test pit, block sampling, in-situ density test, auger boring, permeability test on ground surface, borehole shear test and dynamic cone test and so forth were selected. In addition, the reliability of the results will be increased through comparing with those by laboratory tests. Hence, the experiments are hard to enter the sites without temporary road and, if possible, licensing and many times are needed, too. Small size experiments are indeed necessary to get accurate parameters.

• Journal of the Korea Society of Computer and Information
• /
• v.12 no.3
• /
• pp.165-175
• /
• 2007

The mobile agent executes a given task by which the agent code moves to the server directly. Therefore, node migration method becomes an important factor which impact on the whole performance of distributed system. In this paper, we propose an adaptive migration path technique of mobile agent using the metadata of naming agent. In this proposed technique, node selection for migration depends on the content of referenced metadata, and the reliability of migrated information is determined by the metadata updating method and cooperative operations of individual agents in multi-agents system. For these, we design the metadata using by the number of hit documents, hit ratio, node processing time and network delay time, and describe the methods for creating, using and updating metadata for which determine the adaptive node migration path of mobile agent according to the cooperation of individual agents and number of hit documents using by designed metadata. And results of evaluated performance for proposed adaptive migration path technique through the proper experiment and analysis gain rate of high effective information earning, because of high hit ratio(72%) about of fathered documents by case of applying metadata move to the 13 nodes. But, in case of non-applying metadata is hit ratio(46%) of gathered documents and rate of effective information earning about of 26 nodes is 36.8%.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.1
• /
• pp.86-95
• /
• 2014

Productivity improvement of a shipbuilding company depends on how efficiently its limited resources are managed and utilized. Recently, research on modeling and simulation (M&S) to support shipyard production management system has been being under study. The production management based on M&S rejects decision making on experience, and it can establish productivity improvement method based on quantitative and specific data. In this paper, M&S is applied to the long-term plan as a part of the production planning in shipyards. To this end, the long-term plan processes and related management systems are analyzed. Based on the analysis, a simulation model and an application system using commercial simulation software are suggested. And basic structure of the suggested system is based on web technology such as Rich Internet Application, web services protocol for compatibility with existing shipyard enterprise systems. Utilizing the results of this study, it is expected that shipyard production planners can settle down work flow, in which one can establishes the production plan, simulates the plan, and analyzes the results, enabling a more reliable production plans.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.2
• /
• pp.137-143
• /
• 2020

The CM247LC, a Ni-based superalloy material used for gas turbine hot gas path parts, is casted using directionally solidified technology to analyze the mechanical properties and microstructures through HIP (Hot Isostatic Pressing) and post-heat treatment, and to derive optimal HIP treatment conditions. The CM247LC material is being researched in various ways as an alternative material for prototyping gas turbine blades. In particular, the blade rotating part is exposed and operated in a high temperature and high-pressure environment, and when damaged, it may cause huge economic losses. Therefore, in order to use the CM247LC material as prototyping materials for gas turbine blades, the reliability of the microstructure and mechanical properties must be verified. In this study, after casting rod test specimens using CM247LC material by directionally solidified technology, after that the specimens were performed by HIP treatment and post-heat treatment to test two HIP conditions designed by KEPCO to derive the possibility of prototyping of CM247LC material and optimization of HIP treatment conditions. Additionally, the properties of CM247LC material were compared to the GTD111DS material using for 1,300℃ class gas turbine blades.

• Applied Biological Chemistry
• /
• v.42 no.1
• /
• pp.58-62
• /
• 1999

Method to access qualities of brown sauce and optimize its cooking conditions was studied by sensory evaluation and response surface methodology. Cooks of an hotel, sauce experts, were selected as sensory panelists, and the brown sauce cooking conditions practically used in an hotel were adopted to prepare sauce samples for the sensory test. The cooking conditions were designed with two factors, i.e., one factor of roux contents with three levels and the other factor of cooking times with three levels, which were known as most important in sauce cooking. Sensory acceptance evaluation with intensity 7 grades was applied for several sauce attributes such as color, flavour, viscosity, taste and overall. Ability of each panel to perceive the differences between the brown sauces prepared under different cooking conditions was judged, and only data of the 9 panelists proved as reliable among the 12 panelists were reflected. The acceptances by different cooking conditions were found to be in the order of 11 > 9 > 13% roux contents and 8 > 9 > 7 hr cooking times. Response surface methodology was treated with second-order model on the sensory data and the optimum cooking conditions with the highest acceptances were $10.3{\sim}10.8%$ roux content and 8 hr cooking time.

• Journal of the Korea Concrete Institute
• /
• v.22 no.1
• /
• pp.123-130
• /
• 2010

In this study, mixed recycled coarse aggregate (RCA) was produced by mixing RCA from waste concrete in order to evaluate a new method of RCA production. Bond strength between reinforcing bars and RCA concrete was qualitatively evaluated as a part of continuous studies to establish design code of reinforced concrete structural members using recycled aggregate. For practical application, specimens were manufactured with the ready mix RCA concrete. Parameters investigated include: concrete compressive strength (i.e 21, 27 and 40 MPa), replacement levels (i.e 0, 30, 60 and 100%), bar position (i.e vertical and horizontal) and bar location (75 and 225 mm). For the pull-out test, each specimen was in the form of a cube, with each side of 150 mm in length and a deformed bar, 16 mm in diameter, was embedded in the center of each specimen. From the test results, the most of HT type specimen with compressive strength of 21 and 27 MPa showed lower bond strength than the ones provided in CEB-FIP and considered in reinforcement location factor ($\alpha\;=\;1.3$). It was reasoned that bonded area of top bar specimen was reduced at the soffit of reinforcement because of bleed water of fresh concrete. Therefore the reinforcement location factor in current KCI design code should be reviewed and modified.

• Journal of Oral Medicine and Pain
• /
• v.30 no.2
• /
• pp.257-268
• /
• 2005

It is recently suggested in Korea that Resource-Based Relative Value Scale (RBRVS) is an alternative plan of Korean Dental Fee Schedule which has been operated on a fee-for-service basis since the introduction of the national health insurance program in 1977. RBRVS applicable to diagnosis and treatment for temporomandibular disorders (TMD), a common cause of orofacial pain, is needed to be estimated in Korea and the establishment of the standard terminology of dental procedures for TMD should be preceded. The purposes of this study were to develop a new classification system of health care service items for TMD and to investigate time needed for each item, which enables RBRVS to be estimated prior to establishment the payment system of health care services for TMD. The dental service items for TMD in this study were categorized through Delphi process which 10 TMD specialists were participated in and the time needed for each service item was investigated by work sampling and time study method with a stopwatch. The results of this study demonstrated the new classification system of dental services for TMD comprising 151 service items and exhibited the average time for each items ranging from 7.22 min for cold laser therapy to 171.71 min for direct fabrication of anterior repositioning splint. Conclusively, it is suggested that the classification system for TMD developed in this study, considering specific characteristics on basis of resources for health care service of dental procedures, should be helpful to estimate payment level for each service item.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.33-39
• /
• 2020

In this paper, we propose the design technique of the vehicle's load weight measuring system using tire pressure, which is one of the physical elements of tires. The proposed technique consists of four processes: noise correction by load and vibration, gas flow correction, data mixer and weight conversion. Noise correction by load and vibration eliminates noise that increases the tire's internal pressure due to external shocks and vibrations produced by the vehicle while it is in motion. In the gas flow correction process, the noise of the internal pressure of the tire is increased due to the temperature rise of the ground with respect to the data obtained through the noise correction process due to the load and vibration. In the data mixer process, the load and pressure on the tolerances the empty, median and the full load are classified according to the change in pressure of the tire that is delivered perpendicular to the tire in the event of cargo. In the weight conversion process, weight is expressed by weight through weight conversion algorithms using noise correction results by load and vibration and gas flow correction. The weight conversion algorithm calculates the weight conversion factor, which is the slope of the linear function with respect to the load and pressure change, and converts the weight. In order to evaluate the accuracy of the loading weight measurement system of the vehicle using the tire pneumatic system technique proposed in this paper, we propose the design technique of the vehicle's load weight measuring system using tire pressure, which is one of the physical elements of tires.. Noise correction results by load and vibration and gas flow data correction results showed reliable results. In addition, repeated weight precision test showed better weight accuracy than the standard value of 90% of domestic companies.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.8B
• /
• pp.637-646
• /
• 2012

Recently, Wireless Sensor Networks (WSNs) are used in many applications. When sensor nodes are deployed on special areas, where humans have any difficulties to get in, the nodes form network topology themselves. By using the sensor nodes, users are able to obtain environmental information. Due to the lack of the battery capability, sensor nodes should be efficiently managed with energy consumption in WSNs. In specific applications (e.g. in intrusion detections), intruders tend to occur unexpectedly. For the energy efficiency in the applications, an appropriate algorithm is strongly required. In this paper, we propose tree-based routing algorithm for the specific applications, which based on the intrusion detection. In addition, In order to decrease traffic density, the proposed algorithm provides enhanced method considering link cost and load balance, and it establishes efficient links amongst the sensor nodes. Simultaneously, by using the proposed scheme, parent and child nodes are (re-)defined. Furthermore, efficient routing table management facilitates to improve energy efficiency especially in the limited power source. In order to apply a realistic military environment, in this paper, we design three scenarios according to an intruder's moving direction; (1) the intruder is passing along a path where sensor nodes have been already deployed. (2) the intruders are crossing the path. (3) the intruders, who are moving as (1)'s scenario, are certainly deviating from the middle of the path. In conclusion, through the simulation results, we obtain the performance results in terms of latency and energy consumption, and analyze them. Finally, we validate our algorithm is highly able to adapt on such the application environments.