• Journal of Korean Society of Steel Construction
• /
• v.15 no.4 s.65
• /
• pp.341-358
• /
• 2003

This paper proposed a general formulation of Life-Cycle Cost (LCC) models and LCC effective design system models of steel bridges suitable for practical implementation. An LCC model for the optimum design of steel bridges included initial cost and direct/indirect rehabilitation costs of a steel bridge as well as repair/replacement costs, loss of contents or fatality and injury losses, road user costs, and indirect socioeconomic losses. The new road user cost model and regional socioeconomic losses model were especially considered because of the traffic network. Illustrative design examples of an actual steel box girder and an orthotropic steel deck bridge were discussed to demonstrate the LCC effectiveness of the design of steel bridges. Based on the results of the numerical investigation, the LCC-effective optimum design of steel bridges based on the proposed LCC model was found to lead to a more rational, economical, and safer design compared with the initial cost-optimum design and the conventional code-based design.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.6
• /
• pp.197-202
• /
• 2016

In this paper, we propose optimal smart home security monitoring system. Proposeed optimal smart home security system using the three types of ultrasonic sensors were tested to obtain reliable data. and Using Raspberry Pi3, the smart home security system was implemented. In addition, It was verified through experiments optimal efficiency with a small amount compared to the conventional sensor of the home security system by the two ultrasonic sensors located in the optimal position. It was able to use two ultrasonic sensors to determine whether the intruder's highly efficient and reliable intrusion, and connect the servo motor at the bottom of the camera so you can shoot adjusted to the attacker's location to shoot the intruder's image. In addition, by using a Web server and stored the recorded image and two ultrasonic sensor data and provide a Web page for a user to monitor at all remote locations.

• Proceedings of the Korean Reliability Society Conference
• /
• 2002.06a
• /
• pp.111-111
• /
• 2002

당사 제품인 건설 중장비용 대형 용접 구조물에 대하여, 설계단계부터 구조해석 및 초도품에 대한 Rig Test, 실차 시험 등 여러 단계를 거쳐 내구성을 평가하고 있다. 그러나 용접품 특성상 수명 평가 및 예측이 용이하지 않아 특히 내구성 개선 또는 효율 증대를 위한 경량화 등의 필요에 따른 설계 변경시 시행착오를 거치는 경우가 많다. 이에 개발 일정의 지연, 시험 비용의 증대 등이 불가피하고, 보증 수명의 증대를 통한시장 확대 등에 있어서도 애로가 있다. 또한 기존 Rig Test의 경우도 실제 사용환경과의 차이 등으로 인해 필드에서의 사용 수명을 예측하는데 한계가 있다. 이에 당 센터에서는 통계적 분석을 통한 사용 조건의 DB 구축과 제품 품질 DB의 구축 및 통합을 통하여 제관품의 특성을 반영한 용접 구조물의 가속 수명 평가법의 신뢰도 향상과 시장 목표에 부합하는 최적 설계 달성을 위한 독자적 Tool을 개발하고 있으며, 이에 대한 첫 번째 과제로 기확보 데이터에 대한 상관관계를 분석하였다.

• Journal of the Korea Convergence Society
• /
• v.9 no.7
• /
• pp.223-230
• /
• 2018

In the case of a one-shot logistic equipment system that has been stored for a long time, reliability changes with the passage of time. Therefore, when the time comes to use, the storage reliability of the product is an important quality characteristic, and the existing studies have focused on the research for calculating the optimal period inspection cycle to improve the storage reliability. In this study, we analyzed the influence of the two factors on the storage reliability at the convergence point by analyzing the design reliability as well as the periodic inspection cycle. To do this, we applied the existing Martinez storage reliability model to the missile, a representative product of a one-shot system, and analyzed the quantitative effects of the design reliability and the periodic inspection cycle. From the results of the analysis, it was confirmed that the maintenance of the periodic inspection cycle is more important for the improvement of the storage reliability than the design reliability in the design reliability category of the current product.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.2
• /
• pp.95-107
• /
• 2002

A reliability analysis on sliding of monolithic vertical caisson of composite breakwaters is extensively carried out in order to make the basis for the applicability of reliability-based design method. The required width of caisson of composite breakwaters is determined by the deterministic design method including the effect of impulsive breaking waves as a function of water depth, also studied interactively with the results of reliability analyses. It is found that the safety factor applied in current design may be a little over-weighted magnitude for the sliding of caisson. The reliability index/failure probability is also seen to slowly decrease as the water depth increases for a given wave condition and a safety factor. In addition, optimal safety factor can roughly be evaluated by using the concept of target reliability index for several incident waves. The variations of optimal safety factor may be resulted from the different wave conditions. Finally, it may be concluded from the sensitivity studies that the reliability index may be more depended on the incident wave angles and the wave periodsrather than on the bottom slopes and the thickness of rubble mound.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.4
• /
• pp.123-133
• /
• 1992

확률이론을 이용한 구조물 신뢰성에 관한 연구가 최근 급속히 발달함과 동시에 구조물의 저하능력과 작용하중들의 확률적 특성들에 대한 인식이 제고됨에 따라 여러나라에서 확률이론에 근거한 설계규준이 개발되고 있다. 작용하중이나 구조저항력의 확률적 특성을 보이고 있기 때문에 외국의 설계규준을 직접 도입하는 것은 여러 가지 문제점이 있으며, 따라서 국내현실에 적합한 설계규준에 대한 연구가 필요하다. 본 연구에서는 국내 철근콘크리트 구조물의 합리적인 설계규준을 제시하기 위하여 국내에서 수집\ulcorner분석된 구조부재강도 및 작용하중의 확률적 모형을 이용하여 현행 설계규준에 내포된 신뢰도를 검정하고 나아가 최적하중계수를 분석하였다.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1995.04a
• /
• pp.678-681
• /
• 1995

가속수명시험은 매우 신뢰성이 높은 제품의 수명분포에 대한 정보를 빨리 얻기 위해 사용된다. 이때, 빠른 시간안에 정보를 얻기 위해 제품의 사용조건보다 높은 스트레스 즉 온도, 압력, 전압, 진동등을 사용하여 시험을 하게 되는데 최대 시험 스트레스는 미리 실험자에 의해 선택되게 된다. 그러나 주어진 최대 시험 스트레스가 스트레스의 한계범위를 벗어나는 경우에는 사용조건과 다른 고장구조가 발생할 수 있고, 이로 인하여 편의가 큰 신뢰수명의 추정치를 얻을 수 있다. 기존의 논문에서는 실험자의 경험 또는 사전시험을 통해 미리 설정된 최대 시험 스트레스하에서 제품수명의 표준편차를 최소화하기 위한 최적가속수명시험 설계방법을 제시하였다. 그러나 본 논문에서는 와이불 분포에서 1) 사용조건에서의 수명추정치의 분산 .leq. k, 2) 스트레스의 범위를 벗어나지 않는 최대 시험 스트레스의 최소값을 구하는 설계방법을 제시하고, 또한 구한 스트레스에서의 수명 및 최소 시험 스트레스에서 시험되어야 할 제품의 수를 추정한다. 이때, 사용전압에서의 수명을 계산하기 위하여 inverse power law 모형을 도입하였으며, type I censoring 방법을 사용하여 수명 데이타들은 모든 제품이 고장나기 전에 분석될 수 있도록 하였다.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.6
• /
• pp.107-113
• /
• 2004

This paper presents the pillar section optimization technique considering the reliability of the vehicle body structure consisted of complicated thin-walled panels. The response surface method is utilized to obtain the response surface models that describe the approximate performance functions representing the system characteristics on the section properties of the pillar and on the mass and the natural frequencies of the vehicle B.I.W. The reliability-based design optimization on the pillar sections Is performed and compared with the conventional deterministic optimization. The FORM is applied for the reliability analysis of the vehicle body structure. The developed optimization system is applied to the pillar section design considering the fundamental natural frequencies of passenger car body structure. By applying the proposed RBDO technique, it can be possible to optimize the pillar sections considering the reliability that engineers require.

• Computational Structural Engineering
• /
• v.5 no.2
• /
• pp.93-104
• /
• 1992

The final objective of optimization methods is to find global optimum accurately and efficiently. The optmization processes by simulated annealing and genetic algorithm which have stochastic search process are examined and are applied to several mathematical models and truss, beam structures. Then the robustnesses of these two methods are studied and compared with the results of deterministic optimization methods from the viewpoints of reliability and running time in obtaining the global optimum.

• Computational Structural Engineering
• /
• v.10 no.4
• /
• pp.349-358
• /
• 1997

The present paper describes an investigation into the application of the genetic algorithm (GA) in the optimum design of composite laminated structure. Stochastic processes generate an initial population of designs and then apply principles of natural selection/survival of the fittest to improve the designs. The five test functions are used to verify the robustness and reliability of the GA, and as a numerical example, minimum weight of a cantilever composite laminated beam with a mix of continuous, integer and discrete design variables is obtained by using the GA with exterior penalty function method. The design problem has constraints on strength, displacements, and natural frequencies, and is formulated to a multidimensional nonlinear form. From the results, it is found that the GA search technique is very effective to find the good optimum solution as well as has higher robustness.