• Journal of Broadcast Engineering
• /
• v.16 no.1
• /
• pp.44-53
• /
• 2011

In this paper, we propose a 3D conversion algorithm of 2D video using depth layer partition method. In the proposed algorithm, we first set frame groups using cut detection algorithm. Each divided frame groups will reduce the possibility of error propagation in the process of motion estimation. Depth image generation is the core technique in 2D/3D conversion algorithm. Therefore, we use two depth map generation algorithms. In the first, segmentation and motion information are used, and in the other, edge directional histogram is used. After applying depth layer partition algorithm which separates objects(foreground) and the background from the original image, the extracted two depth maps are properly merged. Through experiments, we verify that the proposed algorithm generates reliable depth map and good conversion results.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.3
• /
• pp.86-94
• /
• 1990

This paper suggests a unified packet telecommunication network, which is designed by applying network design algorithm and distribution network design algorithm, Proposed local network design algorithm is based on MST topology, and it can satisfy the limited capacity and get a distribution effect of communication flow, With the result of the comparison with Kruskal and Esau-Willams algorithm, an increase of 2.7% in cost and a decrease of 44.8% in average delay time are shown. Starting with MST topology, proposed distribution network design algorithm gradually increases its reliability, and proposes a conclusive algorithm to determine a topology with minimum cost. In compared with Cut-Saturation algorithm in the aspect of end-to-end delay time and communication flow restricted condition, this proposed algorithm results in 1/7 cost down and about 2.5 times increases in Throughput.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.39 no.4
• /
• pp.10-18
• /
• 2002

Network topology design is a multiobjective problem with various design components. The components such as cost, message delay and reliability are important to gain the best performance. Recently, Genetic Algorithms(GAs) have been widely used as an optimization method for real-world problems such as combinatorial optimization, network topology design, and so on. This paper proposed a method of Multi-objective GA for Design of the network topology which is to minimize connection cost and message delay time. A common difficulty in multiobjective optimization is the existence of an objective conflict. We used the prufer number and cluster string for encoding, parato elimination method and niche-formation method for the fitness sharing method, and reformation elitism for the prevention of pre-convergence. From the simulation, the proposed method shows that the better candidates of network architecture can be found.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.8
• /
• pp.39-47
• /
• 1999

This paper describes on-line retrainable RBF network in order to control the coiling temperature for a hot coil strip at Pohang Iron & Steel Company(POSCO). The proposed neural network can be used for improving conventional rule-based lookup table, which generates a heat transmission coefficient. To cope with time-varying characteristics of hot coil process, additional synaptic weights for on-line retraining purposes are introduced to hidden-to-output weights of conventional RBF network. Those weights are locally adjusted to newly incoming test data while preserving old information trained with off-line past data. Hence the effect of catastrophic interference can be greatly alleviated with the proposed network. In addition, rejection scheme is introduced for reliability concerns. From the experimental results applied to the actual process, it is noticed that overall control performance represents about 2.2% increase compared to the conventional one.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.48 no.2
• /
• pp.53-64
• /
• 2011

In this paper, we propose a channel estimation of side information method based received motion vectors for distributed video coding. The proposed decoder estimates motion vectors of side information and transmits it to the encoder. As the proposed encoder generates side information which is the same to one in the decoder with received motion vectors, accuracy of side information of the decoder is assessed and it is transmitted to decoder. The proposed decoder can also estimate accurate crossover probability with received error information. As the proposed method conducts correct belief propagation, computational complexity of the channel decoder decreases and error correction capability is significantly improved with the smaller amount of parity bits. Experimental results show that the proposed algorithm is better in rate-distortion performance and it is faster than several conventional distributed video coding methods.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.4 s.316
• /
• pp.101-108
• /
• 2007

Parallel processing algorithms, coupled with advanced networking and distributed computing architectures, improve the overall computational performance, dependability, and versatility of a digital signal processing system In this paper, novel parallel algorithms are introduced and investigated for advanced sonar algorithm, conventional matched-field processing (CMFP). Based on a specific domain, each parallel algorithm decomposes the sequential workload in order to obtain scalable parallel speedup. Depending on the processing requirement of the algorithm, the computational performance of the parallel algorithm reveals different characteristics. The high-complexity algorithm, CMFP shows scalable parallel performance on the array of DSP processors. The impact on parallel performance due to workload balancing, communication scheme, algorithm complexity, processor speed, network performance, and testbed configuration is explored.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.10
• /
• pp.83-98
• /
• 2007

The handover between different radio access networks, especially where their coverage overlaps, suffers various complications since the different access networks provide different service characteristics. One way to reduce service interruptions and QoS (i.e., bandwidth, throughput, delay) degradations during the inter-technology handover is to reserve the required resource in advance. The resource reservation algorithm should minimize the handover latency and maximize the resource utilization based on the accurate estimation on mobile's location, velocity, movement pattern and service requirements. In this paper, we propose a resource reservation algorithm based on the mobile terminal velocity and the cell selection probability, which maximizes resource utilization ana reduces network overhead. We compare the proposed algorithm with PMS(Predictive Mobility Support) and VCDS(Velocity and Call Duration Support scheme) based on 3-layer network model under various scenarios.

• Computational Structural Engineering
• /
• v.7 no.1
• /
• pp.109-116
• /
• 1994

In this paper, various reliability analysis methods for calculating a probability of failure are investigated for their accuracy and efficiency. Crude Monte Carlo method is used as a basis for the comparison of various numerical results. For the sampling methods, Importance Sampling method and Directional Simulation method are considered for overcoming a drawback of Crude Monte Carlo method. For the approximate methods, conventional Rackwitz-Fiessler method. 3-parameter Chen-Lind method, and Rosenblatt transformation method are compared on the basis of First order reliability method. As a Second-order reliability method, Curvature-Fitting paraboloid method, Point-fitting paraboloid method, and Log-likelihood function method are explored in order to verify the accuracy of the reliability calculation results. These methods mentioned above would have some difficulty unless the limit state equation is expressed explicitly in terms of random design variables. Thus, there is a need to develop some general reliability methods for the case where an implicit limit state equation is given. For this purpose, Response surface method is used where the limit state equation is approximated by regression analysis of the response surface outcomes resulted from the structural analysis. From the application of these various reliability methods to three examples, it is found that Directional Simulation method and Response Surface method are very efficient and recommendable for the general reliability analysis problem cases.

• Journal of Energy Engineering
• /
• v.14 no.1
• /
• pp.46-53
• /
• 2005

This paper presents a new approach for determining an accurate incentive levels of Direct Load Control (DLC) program using probabilistic techniques. The economic analysis of DLC resources needs to identify the hourly-by-hourly expected energy-not-served resulting from the random outage characteristics of generators as well as to reflect the availability and duration of DLC resources, which results the computational explosion. Therefore, the conventional methods are based on the scenario approaches to reduce the computation time as well as to avoid the complexity of economic studies. In this paper, we have developed a new technique based on the sequential Monte Carlo simulation to evaluate the required expected load control amount in each hour and to decide the incentive level satisfying the economic constraints. In addition, we have applied the variance reduction technique to enhance the efficiency of the simulation. To show the efficiency and effectiveness of the suggested method, the numerical studies have been performed for the modified IEEE 24-bus reliability test system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.7
• /
• pp.605-618
• /
• 2012

In this study, the possibility of decision error is investigated to identify and improve the reliability of participants in the process of conducting the sound quality analysis for laser printers. So far, there is not a way to identify and express the possibility of individual participant quantitatively. Thus, the decision error model is proposed which is based on the expectation value between the perceived sounds. Through the experimental verification on the laser printers, it was found that the possibility of decision error is affected according to the normalized difference. The possibility of decision error has inversely proportional to the normalized difference between the perceived sounds. When the normalized difference becomes small value, the uncertainly between decisions is inversely increase, and then it is difficult to obtain the proper result in the process of the jury evaluation for laser printers. For this reason, in this study, the proposed decision error model is added in the previous step of the correlation verification. Comparing to the conventional process only using the correlation based method, after the reliability of each participant is verified, the correlation with the mean response of participants is verified. It was found that the participants who were recognized as having unusual preferences are actually identified as having the reliability problem. Based on the results of this study, the proposed decision error model will be helpful to identify and improve the reliability of participants in the following study for the sound quality analysis.