• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.1
• /
• pp.138-144
• /
• 2016

Titanium is resistant to general corrosion and in sea water because of the passivity layer film on the surface of material, but may be attacked by environments that cause breakdown of the protective oxide layer including hydrochloric, sulfuric and phosphoric acids. In this study, the Ti alloys were solution heat treatment 5hours at $1066^{\circ}C$ and $966^{\circ}C$, and followed by aging heat treated, 1, 4, 8 and 16 hours in $500^{\circ}C$, $600^{\circ}C$ and $650^{\circ}C$ respectively. The heat treated specimens were measured micro Vicker's hardness, and then accomplished electrochemical polarization test for comparing corrosion in 1N sulfuric acid solution. Additionally, micro structures were taken for corrosion tested specimens. The results showed that corrosion resistance was higher in solution heat treated alloy than base and age heat treated metal. Measured corrosion resistants were increased as increasing aging heat treatment time and temperature.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.6
• /
• pp.784-791
• /
• 2015

Polyethylene glycol (PEG) impregnation prevents a red pine disk from cross-sectional checking during drying. Percentage of PEG Retention (PPR) was measured by the experimental methods of aceton extraction and moisture conditioning in a saturated salt solution and the effect of acetylation on PEG impregnated wood was investigated. PPRs of the kiln-dried specimens were much higher than those of the air-dried by at least four times and within the kiln-dried specimens those of the sapwood were higher that those of the heartwood by two times. These results were confirmed by the moisture conditioning experiment. Acetylation increased the weights of the kiln-dried specimens much less than those of the air-dried. It was revealed that acetic anhydride solution eluted PEG-1000 in the specimens. It is concluded that kiln-drying is more effective than air-drying for the increase of PPR and that acetylation eliminates the difference between the kiln- and air-dried specimens.

• Composites Research
• /
• v.25 no.4
• /
• pp.117-125
• /
• 2012

Warpage of the film insert molded (FIM) part is caused by an asymmetric residual stress distribution. Asymmetric residual stress and temperature distribution is generated by the retarded heat transfer in the perpendicular direction to the attached film surface. Since warpage was not prevented by controlling injection molding conditions, glass fiber (GF) filled composites were employed as substrates for film insert molding to minimize the warpage. Distribution of short GFs was evaluated by using micro-CT equipment. Proper models for micro mechanics, anisotropic thermal expansion coefficients, and closure approximation should be selected in order to calculate fiber orientation tensor and warpage of the FIM part with the composite substrate. After six kinds of micro mechanics models, three models of the thermal expansion coefficient and five models of the closure approximation had been considered, the Mori-Tanaka model, the Rosen and Hashin model, and the third orthotropic closure approximation were selected in this study. The numerically predicted results on fiber orientation tensor and warpage were in good agreement with experimental results and effects of GF reinforcement on warpage of the FIM composite specimen were identified by the numerical results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.12
• /
• pp.1591-1597
• /
• 2012

Adherend samples were made from unsaturated polyester and woven and mat glass fibers by the hand layup and vacuum methods. The mechanical properties of the adhesive, composite adherends, and terminal-joint and secondary-joint specimens were determined experimentally. Combinations of the experiment results and the bonding theory were used in this study. The maximum and average shear stresses were calculated based on the maximum tensile force and geometry parameters of the joint specimens. The results of the maximum and average shear stresses were compared and evaluated for six joints. The results showed that the grinding and grind/acetone joint had the highest strength among three types of terminal-joints. Similarly, the mat-mat and mat-woven joints had the highest strength among three types of secondary-joints with the same value. Conversely, no treatment and woven-woven bonding had very low strength. In each case, failure occurred always at two ends and then moved toward the middle area of the overlap length.

• Korean Journal of Materials Research
• /
• v.9 no.9
• /
• pp.937-942
• /
• 1999

Fe계 합금의 적층결함에너지를 감소시키는 것으로 알려진 Mn이 Fe-20Cr-1C-Si 경면처리 합금의 변형유기 상변태거동과 상온 및 고온 마모저항성에 미치는 영향에 대하여 조사하였다. 15ksi의 접촉응력에 대하여 0~25wt.% Mn을 첨가한 시편은 모두 상온에서 마모손실량이 적은 우수한 마모저항성을 보였는데 Mn 첨가량이 5wt.% 이하인 시편의 경우 마모표면에서 ${\gamma}$$\longrightarrow$$\alpha$\`변형유기 상변태가 발생한 반면 15wt.% 이상 Mn을 첨가한 시편에서는 ${\gamma}$$\longrightarrow$$\varepsilon$변형유기 상변태가 발생하는 것으로 나타났다. 25$0^{\circ}C$까지 고온 마모시험결과 ${\gamma}$$\longrightarrow$$\alpha$\`변형유기 상변태가 발생한 5wt.% 이하 Mn 첨가시편은 Mn 첨가량이 증가할수록 마모손실량이 증가하는 것으로 보아 Mn 첨가는 ${\gamma}$$\longrightarrow$$\alpha$\`변형유기 상변태에 있어서 고온 마모저항성을 저하시키는 것으로 생각되며 이는 Mn이 ${\gamma}$$\longrightarrow$$\alpha$\`변형유기 상변태의 M(sub)d 온도를 감소시키기 때문으로 생각된다. 반면에 ${\gamma}$$\longrightarrow$$\varepsilon$변형유기 상변태가 일어난 15wt.% 이상 Mn 첨가 시편의 경우 Mn 첨가량 증가에 따른 고온 마모손실량의 차이가 없는 것으로 보아 ${\gamma}$$\longrightarrow$$\varepsilon$변형유기 상변태는 ${\gamma}$$\longrightarrow$$\alpha$\`변형유기 상변태에 비해 온도의 존성이 적은 것으로 생각된다.

• Journal of Conservation Science
• /
• v.33 no.5
• /
• pp.345-354
• /
• 2017

A mural was discovered in the Ssanggyesa temple located in Jindo island, during repair of the Daeungjeon Hall. A study was conducted to determine the binding medium used for preparing the mural. Pyrolysis/GC/MS and IR spectrometry were used to analyze a painting specimen. Direct approach and on-line methylation approach were attempted for the pyrolysis/GC/MS. In IR analysis, the spectra of the specimen were found to be different from those of Asian lacquer, yellow lacquer, animal glue, and acrylic emulsion resin. They were also not identical to the standard IR spectra of drying oils such as linseed oil. Pyrolysis/GC/MS results of the specimen were different from those of Asian lacquer, yellow lacquer, animal glue, and acrylic emulsion resin. In the mean time, palmitic acid, octadecanoic acid, nonanedioic acid, and octadecenoic acid, which are characteristic pyrolysis products of dried drying oil, were detected. In addition, the pyrolysis/GC/MS chromatograms of the specimen and dried drying oil were also very similar. Therefore, it was concluded that the painting was prepared using drying oil as a binding medium.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.4
• /
• pp.79-88
• /
• 2007

Concrete structures undergo degradation of durability performance and it generally propagates to the structural problems. Recently. a lot of materials for surface protection for concrete are developed, however, performance is not clearly improved due to the difficulties such as repair construction technique and quality of materials for repairing. In this study, liquid inorganic impregnant for concrete structures is developed and durability performance for impregnated concrete specimens is carried out. Furthermore, the performances of the concrete specimens with developed impregnant is also compared with those of the specimens with impregnant conventionally used. Additional CSH gel is formed through the reaction of calcium hydroxide ($Ca(OH)_2$) and impregnant with silicate. As a result of the reaction, impregnated concrete is evaluated to have more denser surface and resistance to deterioration. Finally it is experimentally verified that the concrete specimens with developed impregnant show better durability performance than normal specimens and those with conventional impregnant.

• Journal of the Korean Ceramic Society
• /
• v.39 no.12
• /
• pp.1149-1152
• /
• 2002

Indentation was used to analyze high pressure phases of silicon. Phase transformations on both loading time and loading rate were studied. Micro-raman spectroscopy was used to observe the indentation-induced transformations. As the loading time increased, Si-III and Si-XII disappeared and only a-Si was observed in (111) samples. As the loading time increased, the residual stress was removed by creation of cracks or dislocations. At 0.1 mm/min loading rate, pop-in . At 5 mm/min loading rate pop-in was observed in force/displacement curve of (111) sample, but pop-in was not observed in force/displacement curve of (100) sample. This result indicates that the loading rate affects the volume of phase transformation in silicon.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.269-269
• /
• 2011

티타늄-알루미늄(Titanium-Aluminum) 질화물(Nitride)은 고경도 난삭재의 고능률 절삭 분야에 사용되는 공구의 수명 향상을 위한 표면처리 소재로 각광을 받고 있다. 건식고속가공을 효과적으로 수행하기 위해서는 코팅막 재료가 가공 중 발생하는 고온에서도 견디는 우수한 내산화성을 지니면서 내마모, 내충격 특성등의 기계적 성질이 우수한 코팅을 필요로 하며 이러한 분야에 TiAlN을 적용하기 위한 많은 연구가 진행되고 있다. 본 연구에서는 아크(Cathodic Arc) 코팅을 시스템을 이용하여 N2 유량변화에 따라 TiAlN 박막을 제조하고 그 특성을 평가하였다. 아크 소스에 장착된 타겟은 120 $mm{\Phi}$, Ti : Al=50 : 50 at% 의 TiAl 타겟을 사용 하였고, 시편과 타겟 간의 거리는 약 30 cm이며, 시편은 SUS를 사용하였다. 시편을 진공용기에 장착하고 ~10-6 Torr까지 진공배기를 실시하고, Ar 가스를 진공용기 내로 공급하여 ~10-4 Torr에서 시편에 bias (Pulse : 400V)를 인가한 후 아크를 발생시켜 약 5분간 청정을 실시하였다. 플라즈마 청정이 끝나면 시편에 인가된 bias를 차단하고 N2 유량을 변화시키며 코팅을 실시하였다. 질소 유량이 증가함에 따라 색상은 회색에서 어두운 보라색으로 변화하였고 SEM 사진을 통해 Micro paticle 이 감소하는 것을 확인 할 수 있었으며 이는 질소유량이 증가 할수록 표면조도 또한 감소하는 분석결과와도 일치하였다. XRD 분석을 통해 질소 유량이 160 sccm 이상에서 TiAlN이 합성되는 것을 볼 수 있었고 질소 유량이 240 sccm일 때 가장 높은 경도를 보였다. 따라서 본 연구에서 얻어진 결과를 바탕으로 더욱 다양한 조건에서 TiAlN 코팅에 응용한다면 다양한 색상 구현과 내마모성 등에서 많은 장점을 얻을 수 있을 것으로 예상된다.

• Restorative Dentistry and Endodontics
• /
• v.27 no.3
• /
• pp.239-248
• /
• 2002

이 연구의 목적은 와동의 형태가 굴곡강도와 탄성계수 등 복합레진의 물리적 성질에 미치는 영향을 평가하는 것이다. 복합레진은 Clearfil$^{TM}$ AP-X(Kuraray, Japan)와 Esthet-X$^{TM}$(Dentsply, USA)가 이용되었으며, 상아질 접착제는 Clearfil$^{TM}$ SE Bond(Kuraray, Japan)와 Prime & Bond NT$^{TM}$(Dentsply, USA)를 사용하였다. 대조군의 시편은 split steel mold(25mm$\times$2mm$\times$2mm) 내에 상기 2종류의 복합레진을 충전하여 2개의 대조군 시편을 제작하였으며, 2.4 및 3.4의 C-factor를 부여하기 위한 유리 모형와동을 제작하고, 와동 내에 상기 2종류의 복합레진을 충전하기 전 유리와동의 내면은 sandblasting 처리하고 각각의 복합레진과 동일회사 제품의 상기 상아질 접착제로 처리한 후, 복합 레진을 각각 충전하여 4개의 실험군을 제작하였다. 제작된 실험군 시편은 저속 diamond saw로 충전된 복합레진 부위의 중심부를 통과하도록 절단하여 레진기둥(25mm$\times$2mm$\times$2mm)이 되도록 제작하였다. 제작된 시편을 37$^{\circ}C$의 증류수에 24시간 동안 보관 후, 만능시험기(EZ Test, Shimadzu, Japan)를 이용하여 분당 1mm의 crosshead speed로 3점 굴곡강도를 측정하였다. 또 Linometer(R&B, Korea)를 이용하여 복합레진의 중합수축량을 측정하였으며 굴곡강도측정 후 시편의 파단면은 주사전자현미경(S-2300, Hitachi, Japan)을 이용하여 관찰하였다. 실험결과의 통계분석은 95% 수준의 one-way ANOVA/Tukey's test를 이용하여 결과를 얻었다. 실험에 이용된 2종류 복합레진의 굴곡강도와 탄성계수는 C-factor치 증가에 따라 감소하였으며, 파단면 또한 C-factor의 증가에 따라 더 불규칙해지는 양상을 나타내었다. 본 실험의 결과 hybrid형 복합레진이 micro-hybrid형 복합레진에 비해 C-factor의 영향을 더 많이 받는 것으로 나타났으며, 와동의 C-factor증가가 굴곡강도나 탄성계수와 같은 복합레진의 물리적 성질을 저하시킨다는 것을 의미하였다.